Integra DTR-5.5 Component Video in 1, 2, 3 28, 30, RS232, 12V Trigger OUT A/B/C 73, Ir In/Out

DTR-6.5,5.5_En.book Page 11 Wednesday, July 28, 2004 9:07 AM

Front & Rear Panels—Continued

DTR-5.5

1 B CDE 6 G H9 J K

L		M	N
ZONE 2 SPEAKERS	SURROUND BACK	SURROUND SPEAKERS
	SPEAKERS

RS232

COMPONENT VIDEO

IN 3	IN 2	IN 1	OUT
Y				VIDEO 3	VIDEO 2
				IN	OUT	IN
PB
PR
	IN	OUT	IN	IN	OUT	IN
	L
	R
	CD	TAPE		VIDEO 3	VIDEO 2
	Q R S T

	IN3	IN2	IN1	OUT	DIGITAL
					COAXIAL
OPTICAL					IN 2	IN 1
VIDEO 1		DVD	MONITOR			PRE OUT
OUT	IN	IN	OUT
			V
						SUB
						WOOFER
			S

OUT	IN	FRONT	SURR	CENTER	L ZONE 2
					OUT

		SUB	R
	DVD	WOOFER
VIDEO 1

U V W

	L
L
R
	R
	L
	CENTER SPEAKER
	R
	FRONT SPEAKERS
REMOTE
CONTROL
XY	Z

For detailed information, see the pages in parentheses.

ACOMPONENT VIDEO IN 1, 2, 3 (28, 30, 32)

These component video inputs can be used to con- nect AV components with component video outputs, such as DVD players.

BAM ANTENNA (24)

These push terminals are for connecting an AM antenna.

CCOMPONENT VIDEO OUT (27)

This component video output can be used to con- nect a TV or projector with a component video input.

DFM ANTENNA (24)

This jack is for connecting an FM antenna.

ERS232 (38)

This port is for connecting the AV receiver to home automation equipment and external controllers.

F12V TRIGGER OUT A/B/C (73, 78)

These jacks can be connected to the 12-volt trigger inputs on other components. These trigger outputs can each be assigned to an input so that when that input is selected, a 12-volt trigger signal is output.

GIR IN/OUT (78)

These jacks are for connecting the remote sensors included with multiroom kits (sold separately).

HA-BUS

A-BUS is a simple, efficient, elegant audio distribu- tion system. The wiring installation time is signifi- cantly reduced as only a single CAT-5 wire is run to each location. A-BUS is easy to use, reliable, affordable, and most of all, far better sounding than conventional auto former based volume controls.

ZONE 2 OUT: Use CAT-5 (eight conductor twisted) cable to connect directly from the receiver’s A-BUS RI45 Hub to an A-BUS keypad.

Warning:

DO NOT connect A-BUS output to any computer or network connections (i.e. ethernet). it will cause damage to the computer or network components as 24-volt power runs on this same cable to power the amplifier stages of the amplifier module.

IR OUT: Another feature of the A-BUS system is the ability to control source equipment in another room where the A-BUS module is installed. If you wish to control another source from the receiver at the A-BUS keypad by remote control, connect A-BUS or another brands’s IR emitter on the receiver’s 40 K terminal. Then place the emitter on the remote receiver on the front panel.

Typically, the emitter will work when you connect with a 40 K connector. If it does not work, try a 56 K connector.

DC IN: Connect A-Bus power supply. Do not use any other AC Adapter on this connector as it may cause severe damage to the receiver.

IMONITOR OUT (27)

The S-Video or composite video jack should be connected to a video input on your TV or projector.

11