Goldstar LS242CE owner manual Remote Control Operations, Controls

Page 13

Operating Instruction

RemoteControlOperations

Controls

Signal transmitter

5

 

 

1

6

 

 

 

 

 

 

3

4

 

 

 

2

 

CANCEL

10

 

 

7

OFF

SET

9

ON

12

11

 

AUTO CLEAN

8

 

 

17

13

 

 

18

 

 

14

 

 

 

15

 

 

16

Flip-up door (opened)

Operation Mode

Cooling Operation

Auto Operation or Auto Changeover

Healthy Dehumidification Operation

Heating Operation

• Cooling Model(), Heat Pump Model( )

1. START/STOP BUTTON

Operation starts when this button is pressed and stops when the button is pressed again.

2. OPERATION MODE SELECTION BUTTON Used to select the operation mode.

3. ROOM TEMPERATURE SETTING BUTTONS

Used to select the room temperature.

4. INDOOR FAN SPEED SELECTOR Used to select fan speed in four steps low, medium, high and CHAOS.

5. JET COOL

Used to start or stop the speed cooling.(speed cooling operates super high fan speed in cooling mode.)

6. CHAOS SWING BUTTON

Used to stop or start louver movement and set the desired up/down airflow direction.

7.ON/OFF TIMER BUTTONS

Used to set the time of starting and stopping operation. (See page 22)

8.TIME SETTING BUTTONS

Used to adjust the time. (See page 22)

9.TIMER SET/CANCEL BUTTON

Used to set the timer when the desired time is obtained and to cancel the Timer operation. (See page 22)

10.SLEEP MODE AUTO BUTTON

Used to set Sleep Mode Auto operation. (See page 22)

11.AIR CIRCULATION BUTTON

Used to circulate the room air without cooling or heating. (See page 23)

12.ROOM TEMPERATURE CHECKING BUTTON

Used to check the room temperature.

13.NEO PLASMA(OPTIONAL) Used to start or stop the plasma- purification function. (See page 20)

14.HORIZONTAL AIRFLOW DIRECTION CONTROL BUTTON (OPTIONAL) Used to set the desired horizontal airflow direction.

15.RESET BUTTON

Used prior to resetting time.

16.2nd F Button

Used prior to using modes printed in blue at the bottom of buttons. (See page 21)

17.AUTO CLEAN (OPTIONAL) Used to set Auto Clean mode.

18.˚C TO ˚F SWITCHING BUTTON

Used to switch temperature reading from Centigrade to Fahrenheit.

ENGLISH

Owner’s Manual 13

Image 13
Contents Room Air Conditioner Table of Contents Be sure not to do Be sure to follow the instruction Safety PrecautionsThere is risk of fire or electric shock There is risk of electric shockCould cause personal injury Personal injury Explosion, or injury Damage to the product EdgesShock Oxygen deficiency could occur There is risk of fire or product failureThere is risk of explosion or fire There is risk of electrical shockThere is risk of fire or electrical shock It may cause a problem for your neighborsBad connection may cause water leakage To avoid vibration or water leakageThis could damage your health Avoid personal injuryProduct There is risk of personal injuryThere is risk of fire or explosion Be careful and avoid personal injuryThey may burn or explode Prior To Operation ServicePreparing For Operation UsageFeatures Symbols Used In This ManualIntroduction IndoorElectrical Safety Operating Instruction Controls Remote Control OperationsGentle Breeze by the Chaos logic Cooling operationDuring Auto Operation Auto operation OptionalDuring Auto Changeover Operation Auto changeover operationOptionalHealthy dehumidification operation Fan speed mode is shiftedDuring Healthy Dehumidification Operation Temperature can be set within a range Close the door of the remote controllerRemote controller still closed. You can Heating operation Heat pump model onlyJet cool operation NEO Plasma Air Purifying Operation only NEO Plasma purification operationOptionalButton is pressed again 2nd F operationSleep mode Additional FeaturesSetting the time Delay start/Pre-set stopVertical Airflow Direction Control Adjust the left/right airflow direction by handForced operation Auto clean OptionalTest operation 22C71.6F 23C73.4F 24C75.2FTo enable function To disable functionAuto restart Helpful informationIndoor Unit Maintenance And ServiceAir conditioner is operating normally when Outdoor UnitAir conditioner may be operating abnormally when TroubleshootingAir conditioner does not start Air conditioner does not cool as it shouldNo A20434H