Integra DTR-8.2 instruction manual From connecting block, Other component

Page 25

Operating components not reached by the remote controller signals (IR IN/OUT)

The following equipment (sold separately) is essential for operation:

•Onkyo’s Multi-Room System kits (IR Remote Controller Extension System), or

•Multiroom A/V distribution and control systems from Niles® and Xantech® to name a few

If the remote controller signal does not reach the DTR-8.2 remote sensor

If the DTR-8.2 is located inside a cabinet or other enclosure where the infrared rays from the remote controller cannot enter, then operation with the remote controller will not be possible. In such a case, it will be necessary to install a remote sensor at a location outside of the cabinet for the infrared rays from the controller to reach.

With this connection, select “Main” for the Hardware Setup → IR IN Setup → Position setting in the Setup menu (see page 31).

Make connection as shown below. Do not plug the equipment into the power source until the connection is complete.

from connecting block

Mini plug cable

I R

IN

OUT

DTR-8.2

If the remote controller signal does not reach other components

IR IN

DTR-8.2

Connecting

IR Receiver

block

 

In this situation, you will need to use a commercially available IR emitter. Connect the mini plug of the IR emitter to the IR OUT terminal on the DTR-8.2 and then place the IR emitter on the remote sensor of the component or facing it. When the IR emitter is connected, only the signal input to the IR IN terminal is output to the IR OUT terminal. The signal input from the remote sensor on the front of the DTR-8.2 will not be output to the IR OUT terminal.

In the cabinet

Remote Controller

Connecting block

IR IN

IR Receiver

DTR-8.2

: Signal flow

The IR IN input allows you to control the DTR-8.2 from the remote zone (Zone 2) with the remote controller even though the remote zone is physically separated. The diagram below shows how to make the proper connections for the remote zone.

With this connection, select “Zone 2” for the Hardware Setup → IR IN Setup → Position setting in the Setup menu (see page 31).

To IR IN

IR Receiver

DTR-8.2

Connecting block

Remote controller

Main room

Zone 2 room

: Signal flow

IR OUT

IR Emitter

Remote Controller

other component

: Signal flow

other component

: Signal flow

 

 

Remote control

 

 

sensor

I R

 

 

IN

 

Emitter

OUT

Mini plug

Mini plug cable

 

DTR-8.2

IR Emitter

 

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents DTR-8.2 Avis Important SafeguardsPrecautions Contents Contents Supplied accessories FeaturesUsing the remote controller Before using this unitInsert batteries Front panel Front panel facilitiesFront door Front panel displayFront panel facilities Preset / buttons Tuning / buttonsEnter button Return buttonRemote controller Remote controller Zone Digital INPUT/OUTPUT coaxial and optical Rear panel facilitiesImproper connection Inserted completely Coaxial cableRear panel facilities Power amplifier3 4 RCA typePower off function Power on/ready function12V Trigger A/B/ZONE 2 terminal Direct change functionDecoder Video jackConnecting a turntable PH Connecting your audio componentsConnecting a compact disc player CD ConnectionsFlow of the video signals is as follows Connecting your video componentsConnecting a DVD player DVD Signal flow Audio connection cable Left white Right redConnecting a video cassette recorder Video Connecting a television monitor or projector Connecting video camera, etc. VideoIdeal speaker configuration Connecting speakersMinimum speaker configuration for surround sound playback Speaker placementConnecting speakers Connecting speakersConnecting the speaker cable Connecting a subwooferWhen using the Surr BACK/ZONE 2 Speakers terminals Connecting the remote zone Zone 2 speakersWhen using the Zone 2 OUT terminals When using the Surr BACK/ZONE 2 PRE OUT terminalsOther component From connecting blockConnecting the AM antenna cable Connecting antennasConnecting the included antennas Assembling the AM loop antennaConnecting an FM outdoor antenna Connecting antennasConnecting an AM outdoor antenna Directional linkageConnecting the power Basic Menu Setup menusAdvanced Menu Navigating through the Setup menu Setup menusWhen using the buttons on the front panel Press the Setup buttonHardware Setup menu Hardware SetupIR in Setup sub-menu Speaker Impedance sub-menuSpeaker Setup menu Speaker SetupSpeaker Config sub-menu Speaker Distance sub-menu Speaker SetupCalibrating the speaker levels Level Calibration sub-menuLeft RightBass Peak Level Limiter Bass Peak Level Bass Peak Level Manager* sub-menuPeak Level Input Setup menu Input SetupDigital Setup sub-menu Initial settings for each input sourceMultichannel Setup sub-menu Input SetupDigital Input Digital FormatLast Valid enables the source last selected The source that Video Setup sub-menuVideo Component VideoIntelli Volume Intelli Volume sub-menuCharacter Input sub-menu Character DisplayRelationship between input source and listening mode Listening Mode Preset sub-menuListening Modes Input source signalsTrigger Setup sub-menu Audio Adjust Setup menu Audio AdjustAudio Adjust Surr Mode Analog/PCM Surround SetupSurr Mode D.F.2ch Pro Logic II Music DimensionDecoder THX SetupTHX Surround EX Dolby D Front EffectPreference Volume Setup sub-menuPreference menu OSD Setup sub-menu Headphones Level Setup sub-menuPreference OSD Position sub-menuListening to a stereo radio station FM mode Tuning into a radio stationFM Mode Press either the AM or FM input Source button TuningSelecting a preset radio station Presetting a radio stationErasing a preset radio station Listening to Radio BroadcastsListening with headphones Adjusting the bass and trebleEnjoying music or videos with the DTR-8.2 Temporarily turning off the soundDirect Setup Pure Audio Enter Return Changing the listening modeRemote controller only Enjoying music or videos with the DTR-8.2Using the sleep time remote controller only Switching the displayAdjusting the brightness of the front display Temporarily changing the speaker output levelsUsing the tone control Changing the audio modeEnjoying the multichannel output Direct/Pure AudioEntering names for input sources and tuner stations Setup Enter ReturnTo delete an entered name Selecting an input source using the remote controller Playing music using the buttons on the DTR-8.2Adjusting the volume for the remote zone Enjoying music in the remote zoneRec Out Recording a sourceStart recording at the recording component as desired Recording a source Quick Start Using the remote controllerInsert batteries Operate your components Touch the screen to startModes Quick referenceDirect-access buttons Intelligent Remote ControllerIntroduction Left and Right buttons IntroductionTouchscreen buttons Which Buttons Can Be Programmed?AA batteries Charging the Remote ControllerOptional recharging dock Introduction Getting Started Activate the remote controllerDefine the Brand of Your Device Defining brands by selecting Getting StartedSelect Yes to define the brand of the device to operate Tap NextSelect a code set from the list Select your brand from the listTap Search Defining brands by searchingVia the Home menu Select a DeviceVia the Device menu Using the Left and Right button Adjust the SettingsUsing touchscreen buttons Using the direct-access buttonsSecond setup panel First setup panelThird setup panel Introduction Getting the Maximum out of itProgramming Buttons Working with ModesGetting the Maximum out of it Programming direct-access and Left/Right ButtonsProgramming control panel buttons Programming device itemsLabeling a button Labeling Buttons and Menu ItemsLabeling a menu item Edit the labelAdding devices Adding and Moving DevicesMoving menu items Restore Delete and restoreTap the item you want to restore DeleteEditing macros Recording Macros and Setting TimersRecording macros Editing timers Setting timersOrganizing macros and timers into groups Changing the remote controller’s RF IR Settings Using the remote controller with Radio FrequencySwitch to RF IR mode by using the Mode button Tap RFChoosing Another Channel System requirements ChadEditWith ChadEdit you can General Problems TroubleshootingProgramming Problems Recharging ProblemsHow do I program source switching? Can I program a button to execute more than one command?How do I reset the Remote controller? How do I revert to the original configuration?Overview of Symbols Specifications Troubleshooting guide Video and Audio Troubleshooting guideIf one of the messages shown below appears Amplifier Section Tuner Section

DTR-8.2 specifications

The Integra DTR-8.2 is a high-performance A/V receiver that stands at the crossroads of functionality and sophistication, designed for the discerning audiophile and home theater enthusiast. This powerful receiver offers a robust suite of features and technologies that enhance the listening experience while seamlessly integrating into modern home entertainment setups.

One of the standout features of the DTR-8.2 is its advanced power amplification. With a 9.2 channel configuration, it delivers a potent output, ensuring that every movie, concert, or gaming session is filled with immersive sound. The receiver is equipped with high-current amplification and features a robust power supply, which works in tandem to deliver clear, dynamic audio even at high volumes.

In terms of audio processing, the DTR-8.2 supports Dolby Atmos and DTS:X, two cutting-edge technologies that create a three-dimensional sound environment. This immersive audio experience is further enhanced by its support for various high-resolution audio formats, allowing music lovers to enjoy studio-quality playback of their favorite tracks.

The receiver also features integrated network capabilities, with built-in Wi-Fi and Ethernet connectivity. This allows users to access a wide range of streaming services, including popular platforms like Spotify, Amazon Music, and Tidal. With Chromecast built-in, AirPlay 2, and DTS Play-Fi support, streaming high-quality audio from various devices has never been easier.

Another noteworthy characteristic of the DTR-8.2 is its comprehensive HDMI connectivity. It includes multiple HDMI inputs and outputs that support 4K/60Hz video, HDR10, Dolby Vision, and HDCP 2.2, making it compatible with the latest video formats and ensuring that users are future-proofed against evolving technology.

The Integra DTR-8.2 also incorporates room calibration technology, namely MCACC (Multi-Channel Acoustic Calibration System), which fine-tunes audio output to suit the specific acoustics of the listening space. This ensures that every listener receives an optimal sound experience, regardless of the room's layout.

In conclusion, the Integra DTR-8.2 is a multifaceted A/V receiver that combines cutting-edge audio and video technologies with user-friendly features. Its combination of power, versatility, and high-tech integrations makes it an ideal centerpiece for any home theater system, catering to those who seek both quality and performance in their audio-visual experiences.
Top Page Image Contents