Integra DTR-4.6 Speaker Level Calibration, Repeat so that the volume, Test tone from each

Page 38

DTR-4.6.book Page 38 Thursday, September 22, 2005 1:45 PM

First Time Setup—Continued

4 Use the Up and Down [ ]/[ ]

buttons to select “a. Unit,” and

then use the Left and Right []/[ ] buttons to select:

feet: Select if you want to enter distances in feet. Can be set from 1 to 30 feet in 0.5-foot steps.

meters: Select if you want to enter distances in meters. Can be set from 0.3 to 9 meters in 0.15-meter steps.

5 Use the Up and Down [ ]/[ ] buttons to select each speaker and then use the Left and Right []/[ ] buttons to specify the distance.

Specify the distance from the speaker to your listening position.

6

Repeat step 5 for all speakers.

 

7

Press the [Setup] button.

 

 

Setup closes.

Note:

This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button.

Speaker Level Calibration

With these settings, you can adjust the level of each speaker while listening to the test tone so that the volume of each speaker is the same at the listening position.

Note:

• The speakers cannot be calibrated while the output of the AV receiver is muted or a pair of headphones is connected.

1

Press the [Receiver] Remote

 

 

Mode button, followed by the

 

[Setup] button.

 

The main menu appears onscreen.

38

2 Use the Up and Down []/[ ] buttons to select “3. Speaker Setup,” and then press [Enter]. The Speaker Setup menu appears.

3

Use the Up and Down [

]/[

]

 

buttons to select “Level Calibra-

 

tion,” and then press [Enter].

 

 

The Level Calibration menu appears

 

and the pink noise test tone is output by

 

the front left speaker.

 

 

 

 

3-3.Level Calibration

 

 

 

------------------------

 

 

 

a.Left

:

0dB

 

 

 

b.Center

:

0dB

 

 

 

c.Right

:

0dB

 

 

 

d.Surround R

:

0dB

 

 

 

e.Surround L

:

0dB

 

 

 

f.Subwoofer

:

0dB

 

 

 

Note:

 

 

 

 

 

Speakers that you set to No or None on

 

the Speaker Config menu (page 36)

 

cannot be adjusted.

 

 

 

 

4

Use the Up and Down [

]/[

]

buttons to select each speaker, and use the Left and Right

[]/[ ] buttons to set the vol- ume.

The level can be adjusted from –12 to +12 dB in 1 dB steps (–15 to +12 dB for the subwoofer).

5

Repeat step 4 so that the volume

 

 

of the test tone from each

 

speaker is the same.

 

If you’re using a handheld sound level

 

meter, adjust the level of each speaker

 

so it reads 75 dB SPL at the listening

 

position, measured with C-weighting

 

and slow reading.

 

 

6

Press the [Setup] button.

 

 

Setup closes.

 

 

Note:

The speaker levels can also be changed by using the dedicated buttons on the remote controller. Press the [Test Tone] button to output the test tone. Use the [CH Sel] button to select each speaker, and use the [Level–] and [Level+] buttons to adjust the level.

Image 38
Contents DTR-4.6 Important Safety Instructions AvisPrecautions PowerSpeaker cable labels Supplied AccessoriesMake sure you have the following accessories Contents Features Using the Remote Controller Before Using the AV receiverInstalling the Batteries Getting to Know the AV Receiver Front PanelGetting to Know the AV Receiver DisplayXM antenna Rear PanelComponent Video in 1, 2, IR in A/B and OUTVideo 1 IN/OUT and Video 2 IN/OUT These terminal posts are for connecting speakers in ZoneThis jack is for connecting a powered subwoofer FRONT, CENTER, and Surround SpeakersReceiver/Tape Mode Remote ControllerAbout the Remote Controller Modes Remote Controller DVD Mode CD, MD, and CDR Modes HDD Mode Connecting Your Speakers Enjoying Home TheaterConnecting Your Speakers Connecting Your SpeakersStrip about 5/8 Speaker Connection PrecautionsConnecting the Speaker Cables Connecting the Indoor FM Antenna Connecting AntennaConnecting the AM Loop Antenna Attach the FM antenna, as shownConnecting an Outdoor AM Antenna Connecting AntennaConnecting an Outdoor FM Antenna Using a TV/FM Antenna SplitterOptical Digital Jacks Connecting Your ComponentsAbout AV Connections AV Connection Color CodingWhich Connections Should I Use? Connecting Your ComponentsConnecting Audio and Video Signals to the AV Receiver Video Connection FormatsAudio Connection Connecting a TV or ProjectorVideo Connection HintConnecting a DVD player Or the otherHooking Up the Multichannel DVD Input Connecting a VCR or DVD Recorder for Playback DVD recorderConnecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc CD player Connecting a CD PlayerStep Phono preamp Connecting a TurntableTurntable without a Built-in Phono Preamp Connecting a Cassette, CDR, MiniDisc, or DAT Recorder Remote Control Connecting ComponentsAuto Power On/Standby Direct ChangeConnecting the Power Cord Connecting the Power Cords of Other ComponentsConnecting the RS232 Port Standby indicator lights upTurning On and Standby Do the speaker setup-this is essentialTurning On the AV Receiver Smooth Operation in a Few Easy StepsSpeaker Setup menu appears First Time SetupSpeaker Setup Main menu appears onscreenCrossover First Time SetupSubwoofer Mode Speaker DistanceTest tone from each Repeat so that the volumeSpeaker Level Calibration Speaker is the sameInput selector Default assignment Component Video SetupLowed by the Setup button Press the Receiver button, folInput, and then press Enter Digital Audio Input SetupButtons to select 2. Digital Digital Input menu appearsChanging the Input Display Playing Your AV Components Select a listening mode and enjoySee Using the Listening Modes on Basic AV Receiver OperationListening to AM/FM Stations Tuning into AM/FM Radio StationsListening to the Radio Displaying AM/FM Radio InformationListening to XM Satellite Radio Connecting the XM AntennaListening to the Radio Signing Up for XM Satellite RadioSelecting XM Radio Channels Channel Search modeChannels cannot be selected while Indicator Use the Up and Down Buttons to select a channelNel Displaying XM Radio InformationButtons to select a chan Displaying XM Information on Your TVPositioning the XM Antenna XM Radio MessagesDeleting Presets Presetting AM/FM StationsSelecting Presets XM ChannelsMultichannel DVD Input Settings Using the Multichannel DVD InputUsing the Multichannel DVD Input Subwoofer SensitivityCommon Functions Adjusting Speaker LevelsSetting the Display Brightness Muting the AV ReceiverCommon Functions Using the Sleep TimerUsing Headphones Displaying Source InformationSelecting the Listening Modes Using the Listening ModesSelecting with the Remote Controller Selecting on the AV ReceiverUsing the Listening Modes DSPAbout the Listening Modes Use this mode with any stereo or TV, DVD, VHSUse this mode with any stereo movie e.g., TV, DVD, VHS Onkyo Original DSP ModesRecording the Input Source RecordingRecording Audio and Video from Separate Sources Submenu Main menu Onscreen Setup MenusAbout the Onscreen Setup Menus Using the Cine Filter Function Adjusting the Listening ModesAudio Adjust Menu Adjust, and then press EnterPL II and Neo6 Settings PL II Music 2 ch only Adjusting the Listening ModesTone Control Settings Neo6 MusicLFE Level Setting Dolby Digital SettingsMono/Multiplex Settings MultiplexMode Preset, and then press Default Listening ModesListening Mode Preset menu Appears Use the Up and Down Buttons to select 5. ListeningDelay Advanced SetupInput Setup Volume Setup Advanced SetupIntelliVolume PreferencesLock Setup OSD Setup12V Trigger A/B/C Setup OSD PositionChanging the AV Receiver’s Remote ID Changing the Remote Controller’s IDRemote IDs Opt or coax, and then press Digital Input Signal FormatsThat’s assigned to a digital input Using Only Speakers in Zone Connecting ZoneUsing Another Amp in Zone ZonePowered Zone 2 Setting Zone 2 Out SettingControlling Zone 2 from the AV Receiver Using ZoneControlling Zone 2 with the Remote Controller To adjust On the remote controller, pressZone 2 Remote Mode but Ton, and then use the LevelDelay Using the 12V Triggers in Zone 2 and the Main RoomRepeat this step as necessary for each setting 12V Trigger Setting for Each Input SourceUsing a Multiroom Kit with Other Components Using a Multiroom Kit with a CabinetUsing a Multiroom Kit with Zone Entering Remote Control Codes Controlling Other ComponentsResetting the Remote Mode Buttons Resetting the Remote ControllerRemote Control Codes for Integra Components Connected via Controlling Other ComponentsPrev CH On, Standby, TVCH +/-, TV CH + TV InputLearning Commands from Other Remote Controllers Running Macros Using MacrosMaking Macros Deleting MacrosTroubleshooting Troubleshooting Sound changes when I connect my head- phones Remote controller doesn’t workCan’t learn commands from another remote controller Can’t control other componentsGeneral SpecificationAmplifier Section Video Section

DTR-4.6 specifications

The Integra DTR-4.6 is an advanced multi-channel A/V receiver, designed to deliver an immersive audio and video experience. Renowned for its high-quality construction and cutting-edge technology, this receiver stands out in today’s competitive home theater market.

One of the main features of the DTR-4.6 is its powerful amplification system. It offers a robust 100 watts of power per channel across seven channels, ensuring that even the most demanding audio tracks are handled effortlessly. The receiver is equipped with Integra's proprietary technology which allows for dynamic power distribution, providing listeners with an impactful audio experience without distortion.

In terms of connectivity, the DTR-4.6 boasts a comprehensive range of options. It includes multiple HDMI inputs that support 4K video pass-through, allowing users to connect their latest devices effortlessly. Additionally, the receiver features various analog and digital inputs, ensuring compatibility with a wide range of audio sources, including CD players, turntables, and streaming devices.

For those who prioritize high-resolution audio, the DTR-4.6 supports several advanced formats, including Dolby Atmos and DTS:X. These immersive audio technologies allow sound to move above and around the listener, creating an unparalleled 3D sound experience that enhances movies, games, and music. Furthermore, the receiver features Advanced MultEQ XT room correction technology, which helps optimize sound quality by analyzing the room's acoustics and making real-time adjustments.

Another notable characteristic of the DTR-4.6 is its user-friendly interface. The intuitive on-screen setup and configuration guide make it easy to get started, even for those who may not be tech-savvy. The receiver comes with a convenient remote control, and users can also control it via a mobile app, adding a layer of convenience for modern homeowners.

Finally, the design of the DTR-4.6 is both sleek and functional. Its understated aesthetic, coupled with a solid build, ensures it serves as an attractive centerpiece in any home theater setup. The integration of high-quality components further solidifies its reputation as a durable and reliable choice for audiophiles and home cinema enthusiasts alike.

In conclusion, the Integra DTR-4.6 stands as a testament to the brand's commitment to audio excellence, offering a powerful combination of features, cutting-edge technology, and user-centric design that elevates the home entertainment experience to new heights.