Integra DTR-4.6 instruction manual Troubleshooting

Page 78

DTR-4.6.book Page 78 Thursday, September 22, 2005 1:45 PM

Troubleshooting—Continued

The Zone 2 speakers produce no sound

The Zone 2 speakers only output sources that are con- nected to an analog input. Check to see if the source is connected to an analog input.

There’s no sound with a certain signal format

Check the digital audio output setting on the con- nected device. On some games consoles, such as those that can play DVDs, the default setting is off.

With some DVD-Video discs, you need to select an audio output format from a menu.

Can’t get 5.1-channel playback

When the ZONE 2 SPEAKERS terminals are used, playback in the main room is reduced to stereo play- back.

The volume cannot be set to +18 dB (99)

After the volume level of each speaker has been adjusted (pages 38, 50), the maximum possible vol- ume setting be reduced.

Noise can be heard

Using cable ties to bundle audio cables with power cords, speaker cables, and so on may degrade the audio performance, so don’t do it.

An audio cable may be picking up interference. Try repositioning your cables.

The Late Night function doesn’t work

Make sure the source material is Dolby Digital (page 59).

The multichannel DVD input doesn’t work

Check the multichannel DVD input connections (page 26).

To select the multichannel DVD input, press the [Multi CH] input selector button.

Check the audio output settings on your DVD player.

About DTS signals

When playing DTS program material, using the pause, fast forward, or fast reverse function on your player may produce a short audible noise. This is not a mal- function.

When DTS program material ends and the DTS bit- stream stops, the AV receiver remains in DTS listen- ing mode and the DTS indicator remains on. This is to prevent noise when you use the pause, fast forward, or fast reverse function on your player. If you switch your player from DTS to PCM, because the AV receiver does not switch formats immediately, you may not hear any sound, in which case you should stop your player for about 3 seconds, and then resume playback.

With some CD players, you won’t be able to playback DTS material properly even though your player is con- nected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed (e.g., output level, sampling rate, or frequency response changed) and the AV receiver doesn’t recog- nize it as a genuine DTS signal. In such cases, you may hear noise.

Video

There’s no picture

Make sure that all video connecting plugs are pushed in all the way (page 22).

Make sure that each video component is properly con- nected.

If a video component is connected to a component video input, your TV must be connected to the COM- PONENT VIDEO OUT (page 23).

On your TV, make sure that the video input to which the AV receiver is connected is selected.

To watch a composite video or S-Video source on a TV that’s connected to the COMPONENT VIDEO OUT, select Video in the “Component Video Setup” on page 39.

The onscreen menus don’t appear

On your TV, make sure that the video input to which the AV receiver is connected is selected.

The picture is distorted

With some TVs and projectors, the onscreen setup menus may not appear when the Scan Mode setting is set to Non-Interlaced. In this case, select this setting again by using the AV receiver’s display, and select Interlaced (page 63).

The immediate display does not appear

The immediate display does not appear on a TV that’s connected to the COMPONENT VIDEO OUT.

Tuner

Reception is noisy, stereo FM reception suffers from hiss, or the FM STEREO indicator doesn’t appear

Relocate your antenna.

Move the AV receiver away from your TV or com- puter.

Listen to the station in mono (page 43).

When listening to an AM station, operating the remote controller may cause noise.

Passing cars and airplanes can cause interference.

Concrete walls weaken radio signals.

If nothing improves the reception, install an outdoor antenna.

Can’t select XM radio channels

 

• Channels cannot be selected while the

indica-

tor is flashing, as tuning is in progress.

 

78

Image 78
Contents DTR-4.6 Important Safety Instructions AvisPrecautions PowerSupplied Accessories Make sure you have the following accessoriesSpeaker cable labels Contents Features Before Using the AV receiver Installing the BatteriesUsing the Remote Controller Getting to Know the AV Receiver Front PanelGetting to Know the AV Receiver DisplayXM antenna Rear PanelComponent Video in 1, 2, IR in A/B and OUTVideo 1 IN/OUT and Video 2 IN/OUT These terminal posts are for connecting speakers in ZoneThis jack is for connecting a powered subwoofer FRONT, CENTER, and Surround SpeakersRemote Controller About the Remote Controller ModesReceiver/Tape Mode Remote Controller DVD Mode CD, MD, and CDR Modes HDD Mode Connecting Your Speakers Enjoying Home TheaterConnecting Your Speakers Connecting Your SpeakersSpeaker Connection Precautions Connecting the Speaker CablesStrip about 5/8 Connecting the Indoor FM Antenna Connecting AntennaConnecting the AM Loop Antenna Attach the FM antenna, as shownConnecting an Outdoor AM Antenna Connecting AntennaConnecting an Outdoor FM Antenna Using a TV/FM Antenna SplitterOptical Digital Jacks Connecting Your ComponentsAbout AV Connections AV Connection Color CodingWhich Connections Should I Use? Connecting Your ComponentsConnecting Audio and Video Signals to the AV Receiver Video Connection FormatsAudio Connection Connecting a TV or ProjectorVideo Connection HintConnecting a DVD player Or the otherHooking Up the Multichannel DVD Input Connecting a VCR or DVD Recorder for Playback DVD recorderConnecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Connecting a CD Player StepCD player Connecting a Turntable Turntable without a Built-in Phono PreampPhono preamp Connecting a Cassette, CDR, MiniDisc, or DAT Recorder Remote Control Connecting ComponentsAuto Power On/Standby Direct ChangeConnecting the Power Cord Connecting the Power Cords of Other ComponentsConnecting the RS232 Port Standby indicator lights upTurning On and Standby Do the speaker setup-this is essentialTurning On the AV Receiver Smooth Operation in a Few Easy StepsSpeaker Setup menu appears First Time SetupSpeaker Setup Main menu appears onscreenCrossover First Time SetupSubwoofer Mode Speaker DistanceTest tone from each Repeat so that the volumeSpeaker Level Calibration Speaker is the sameInput selector Default assignment Component Video SetupLowed by the Setup button Press the Receiver button, folInput, and then press Enter Digital Audio Input SetupButtons to select 2. Digital Digital Input menu appearsChanging the Input Display Playing Your AV Components Select a listening mode and enjoySee Using the Listening Modes on Basic AV Receiver OperationListening to AM/FM Stations Tuning into AM/FM Radio StationsListening to the Radio Displaying AM/FM Radio InformationListening to XM Satellite Radio Connecting the XM AntennaListening to the Radio Signing Up for XM Satellite RadioSelecting XM Radio Channels Channel Search modeChannels cannot be selected while Indicator Use the Up and Down Buttons to select a channelNel Displaying XM Radio InformationButtons to select a chan Displaying XM Information on Your TVPositioning the XM Antenna XM Radio MessagesDeleting Presets Presetting AM/FM StationsSelecting Presets XM ChannelsMultichannel DVD Input Settings Using the Multichannel DVD InputUsing the Multichannel DVD Input Subwoofer SensitivityCommon Functions Adjusting Speaker LevelsSetting the Display Brightness Muting the AV ReceiverCommon Functions Using the Sleep TimerUsing Headphones Displaying Source InformationSelecting the Listening Modes Using the Listening ModesSelecting with the Remote Controller Selecting on the AV ReceiverUsing the Listening Modes DSPAbout the Listening Modes Use this mode with any stereo or TV, DVD, VHSUse this mode with any stereo movie e.g., TV, DVD, VHS Onkyo Original DSP ModesRecording Recording Audio and Video from Separate SourcesRecording the Input Source Onscreen Setup Menus About the Onscreen Setup MenusSubmenu Main menu Using the Cine Filter Function Adjusting the Listening ModesAudio Adjust Menu Adjust, and then press EnterPL II and Neo6 Settings PL II Music 2 ch only Adjusting the Listening ModesTone Control Settings Neo6 MusicLFE Level Setting Dolby Digital SettingsMono/Multiplex Settings MultiplexMode Preset, and then press Default Listening ModesListening Mode Preset menu Appears Use the Up and Down Buttons to select 5. ListeningAdvanced Setup Input SetupDelay Volume Setup Advanced SetupIntelliVolume PreferencesLock Setup OSD Setup12V Trigger A/B/C Setup OSD PositionChanging the Remote Controller’s ID Remote IDsChanging the AV Receiver’s Remote ID Digital Input Signal Formats That’s assigned to a digital inputOpt or coax, and then press Using Only Speakers in Zone Connecting ZoneUsing Another Amp in Zone ZonePowered Zone 2 Setting Zone 2 Out SettingUsing Zone Controlling Zone 2 with the Remote ControllerControlling Zone 2 from the AV Receiver To adjust On the remote controller, pressZone 2 Remote Mode but Ton, and then use the LevelDelay Using the 12V Triggers in Zone 2 and the Main RoomRepeat this step as necessary for each setting 12V Trigger Setting for Each Input SourceUsing a Multiroom Kit with a Cabinet Using a Multiroom Kit with ZoneUsing a Multiroom Kit with Other Components Entering Remote Control Codes Controlling Other ComponentsResetting the Remote Mode Buttons Resetting the Remote ControllerRemote Control Codes for Integra Components Connected via Controlling Other ComponentsPrev CH On, Standby, TVCH +/-, TV CH + TV InputLearning Commands from Other Remote Controllers Running Macros Using MacrosMaking Macros Deleting MacrosTroubleshooting Troubleshooting Sound changes when I connect my head- phones Remote controller doesn’t workCan’t learn commands from another remote controller Can’t control other componentsGeneral SpecificationAmplifier Section Video Section

DTR-4.6 specifications

The Integra DTR-4.6 is an advanced multi-channel A/V receiver, designed to deliver an immersive audio and video experience. Renowned for its high-quality construction and cutting-edge technology, this receiver stands out in today’s competitive home theater market.

One of the main features of the DTR-4.6 is its powerful amplification system. It offers a robust 100 watts of power per channel across seven channels, ensuring that even the most demanding audio tracks are handled effortlessly. The receiver is equipped with Integra's proprietary technology which allows for dynamic power distribution, providing listeners with an impactful audio experience without distortion.

In terms of connectivity, the DTR-4.6 boasts a comprehensive range of options. It includes multiple HDMI inputs that support 4K video pass-through, allowing users to connect their latest devices effortlessly. Additionally, the receiver features various analog and digital inputs, ensuring compatibility with a wide range of audio sources, including CD players, turntables, and streaming devices.

For those who prioritize high-resolution audio, the DTR-4.6 supports several advanced formats, including Dolby Atmos and DTS:X. These immersive audio technologies allow sound to move above and around the listener, creating an unparalleled 3D sound experience that enhances movies, games, and music. Furthermore, the receiver features Advanced MultEQ XT room correction technology, which helps optimize sound quality by analyzing the room's acoustics and making real-time adjustments.

Another notable characteristic of the DTR-4.6 is its user-friendly interface. The intuitive on-screen setup and configuration guide make it easy to get started, even for those who may not be tech-savvy. The receiver comes with a convenient remote control, and users can also control it via a mobile app, adding a layer of convenience for modern homeowners.

Finally, the design of the DTR-4.6 is both sleek and functional. Its understated aesthetic, coupled with a solid build, ensures it serves as an attractive centerpiece in any home theater setup. The integration of high-quality components further solidifies its reputation as a durable and reliable choice for audiophiles and home cinema enthusiasts alike.

In conclusion, the Integra DTR-4.6 stands as a testament to the brand's commitment to audio excellence, offering a powerful combination of features, cutting-edge technology, and user-centric design that elevates the home entertainment experience to new heights.