Integra DTR-4.6 instruction manual Using the 12V Triggers in Zone 2 and the Main Room, Delay

Page 70

DTR-4.6.book Page 70 Thursday, September 22, 2005 1:45 PM

Zone 2—Continued

Using the 12V Triggers in Zone 2 and the Main Room

When the AV receiver’s 12 V TRIGGER OUT A/B/C jack is connected to the 12 V trigger input on a con- nected component, you can specify whether or not a 12- volt trigger signal is output when that component is selected as the source for the main room, Zone 2, or either.

Hookup

• Use a miniplug cable to connect the AV receiver’s 12 V TRIGGER OUT A, B, or C jack to the 12 V trig- ger input on the connected component.

1

Press the [Receiver] Remote

 

 

Mode button, followed by the

 

[Setup] button.

 

The main menu appears onscreen.

2

Use the Up and Down [ ]/[ ]

buttons to select “7. Preference,” and then press [Enter].

The Preference menu appears.

3 Use the Up and Down []/[ ] buttons to select “12V Trigger Setup” A, B, or C, and then press [Enter].

4 Use the Up and Down []/[ ] buttons to select “Delay” or an input source, and use the Left and Right []/[ ] buttons to change the setting.

Repeat this step as necessary for each setting.

5

Press the [Setup] button.

 

 

Setup closes.

■Delay

When several components are turned on simultaneously via the 12-volt triggers, depending on the type of compo- nents, a large amount of current may be drawn momen- tarily. To prevent this, you can delay the trigger signals output by the AV receiver. In addition, by delaying the trigger signal for your power amplifier so that it’s the last component to be turned on, you can avoid the “thump” noise that’s sometimes heard when a source component is turned on.

The delay setting determines how long after the input source is changed on the AV receiver the trigger signal is output. It can be set to 0 sec, 1 sec, 2 sec, or 3 sec. When set to 0 sec, the trigger signal is output as soon as the input source is changed.

■12V Trigger Setting for Each Input Source

By default, all input sources on the 12V Trigger A Setup menu are set to Main, those on the 12V Trigger B Setup menu are set to Main/Zone 2, and those on the 12V Trig- ger C Setup menu are set to Zone2.

Off: No trigger signal is output.

Main: Select this if you want to output a 12-volt trig- ger signal when a connected component is selected as the source for the main room.

Zone2: Select this if you want to output a 12-volt trig- ger signal when a connected component is selected as the source for Zone 2.

Main/Zone2: Select this if you want to output a 12-volt trigger signal when a connected component is selected as the source for either the main room or Zone 2.

70

Page 69 Page 71
Image 70
Page 69 Page 71
Contents DTR-4.6 Important Safety Instructions AvisPrecautions PowerMake sure you have the following accessories Supplied AccessoriesSpeaker cable labels Contents Features Installing the Batteries Before Using the AV receiverUsing the Remote Controller Getting to Know the AV Receiver Front PanelGetting to Know the AV Receiver DisplayXM antenna Rear PanelComponent Video in 1, 2, IR in A/B and OUTVideo 1 IN/OUT and Video 2 IN/OUT These terminal posts are for connecting speakers in ZoneThis jack is for connecting a powered subwoofer FRONT, CENTER, and Surround SpeakersAbout the Remote Controller Modes Remote ControllerReceiver/Tape Mode Remote Controller DVD Mode CD, MD, and CDR Modes HDD Mode Connecting Your Speakers Enjoying Home TheaterConnecting Your Speakers Connecting Your SpeakersConnecting the Speaker Cables Speaker Connection PrecautionsStrip about 5/8 Connecting the Indoor FM Antenna Connecting AntennaConnecting the AM Loop Antenna Attach the FM antenna, as shownConnecting an Outdoor AM Antenna Connecting AntennaConnecting an Outdoor FM Antenna Using a TV/FM Antenna SplitterOptical Digital Jacks Connecting Your ComponentsAbout AV Connections AV Connection Color CodingWhich Connections Should I Use? Connecting Your ComponentsConnecting Audio and Video Signals to the AV Receiver Video Connection FormatsAudio Connection Connecting a TV or ProjectorVideo Connection HintConnecting a DVD player Or the otherHooking Up the Multichannel DVD Input Connecting a VCR or DVD Recorder for Playback DVD recorderConnecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Step Connecting a CD PlayerCD player Turntable without a Built-in Phono Preamp Connecting a TurntablePhono preamp Connecting a Cassette, CDR, MiniDisc, or DAT Recorder Remote Control Connecting ComponentsAuto Power On/Standby Direct ChangeConnecting the Power Cord Connecting the Power Cords of Other ComponentsConnecting the RS232 Port Standby indicator lights upTurning On and Standby Do the speaker setup-this is essentialTurning On the AV Receiver Smooth Operation in a Few Easy StepsSpeaker Setup menu appears First Time SetupSpeaker Setup Main menu appears onscreenCrossover First Time SetupSubwoofer Mode Speaker DistanceTest tone from each Repeat so that the volumeSpeaker Level Calibration Speaker is the sameInput selector Default assignment Component Video SetupLowed by the Setup button Press the Receiver button, folInput, and then press Enter Digital Audio Input SetupButtons to select 2. Digital Digital Input menu appearsChanging the Input Display Playing Your AV Components Select a listening mode and enjoySee Using the Listening Modes on Basic AV Receiver OperationListening to AM/FM Stations Tuning into AM/FM Radio StationsListening to the Radio Displaying AM/FM Radio InformationListening to XM Satellite Radio Connecting the XM AntennaListening to the Radio Signing Up for XM Satellite RadioSelecting XM Radio Channels Channel Search modeChannels cannot be selected while Indicator Use the Up and Down Buttons to select a channelNel Displaying XM Radio InformationButtons to select a chan Displaying XM Information on Your TVPositioning the XM Antenna XM Radio MessagesDeleting Presets Presetting AM/FM StationsSelecting Presets XM ChannelsMultichannel DVD Input Settings Using the Multichannel DVD InputUsing the Multichannel DVD Input Subwoofer SensitivityCommon Functions Adjusting Speaker LevelsSetting the Display Brightness Muting the AV ReceiverCommon Functions Using the Sleep TimerUsing Headphones Displaying Source InformationSelecting the Listening Modes Using the Listening ModesSelecting with the Remote Controller Selecting on the AV ReceiverUsing the Listening Modes DSPAbout the Listening Modes Use this mode with any stereo or TV, DVD, VHSUse this mode with any stereo movie e.g., TV, DVD, VHS Onkyo Original DSP ModesRecording Audio and Video from Separate Sources RecordingRecording the Input Source About the Onscreen Setup Menus Onscreen Setup MenusSubmenu Main menu Using the Cine Filter Function Adjusting the Listening ModesAudio Adjust Menu Adjust, and then press EnterPL II and Neo6 Settings PL II Music 2 ch only Adjusting the Listening ModesTone Control Settings Neo6 MusicLFE Level Setting Dolby Digital SettingsMono/Multiplex Settings MultiplexMode Preset, and then press Default Listening ModesListening Mode Preset menu Appears Use the Up and Down Buttons to select 5. ListeningInput Setup Advanced SetupDelay Volume Setup Advanced SetupIntelliVolume PreferencesLock Setup OSD Setup12V Trigger A/B/C Setup OSD PositionRemote IDs Changing the Remote Controller’s IDChanging the AV Receiver’s Remote ID That’s assigned to a digital input Digital Input Signal FormatsOpt or coax, and then press Using Only Speakers in Zone Connecting ZoneUsing Another Amp in Zone ZonePowered Zone 2 Setting Zone 2 Out SettingControlling Zone 2 with the Remote Controller Using ZoneControlling Zone 2 from the AV Receiver To adjust On the remote controller, pressZone 2 Remote Mode but Ton, and then use the LevelDelay Using the 12V Triggers in Zone 2 and the Main RoomRepeat this step as necessary for each setting 12V Trigger Setting for Each Input SourceUsing a Multiroom Kit with Zone Using a Multiroom Kit with a CabinetUsing a Multiroom Kit with Other Components Entering Remote Control Codes Controlling Other ComponentsResetting the Remote Mode Buttons Resetting the Remote ControllerRemote Control Codes for Integra Components Connected via Controlling Other ComponentsPrev CH On, Standby, TVCH +/-, TV CH + TV InputLearning Commands from Other Remote Controllers Running Macros Using MacrosMaking Macros Deleting MacrosTroubleshooting Troubleshooting Sound changes when I connect my head- phones Remote controller doesn’t workCan’t learn commands from another remote controller Can’t control other componentsGeneral SpecificationAmplifier Section Video Section

DTR-4.6 specifications

The Integra DTR-4.6 is an advanced multi-channel A/V receiver, designed to deliver an immersive audio and video experience. Renowned for its high-quality construction and cutting-edge technology, this receiver stands out in today’s competitive home theater market.

One of the main features of the DTR-4.6 is its powerful amplification system. It offers a robust 100 watts of power per channel across seven channels, ensuring that even the most demanding audio tracks are handled effortlessly. The receiver is equipped with Integra's proprietary technology which allows for dynamic power distribution, providing listeners with an impactful audio experience without distortion.

In terms of connectivity, the DTR-4.6 boasts a comprehensive range of options. It includes multiple HDMI inputs that support 4K video pass-through, allowing users to connect their latest devices effortlessly. Additionally, the receiver features various analog and digital inputs, ensuring compatibility with a wide range of audio sources, including CD players, turntables, and streaming devices.

For those who prioritize high-resolution audio, the DTR-4.6 supports several advanced formats, including Dolby Atmos and DTS:X. These immersive audio technologies allow sound to move above and around the listener, creating an unparalleled 3D sound experience that enhances movies, games, and music. Furthermore, the receiver features Advanced MultEQ XT room correction technology, which helps optimize sound quality by analyzing the room's acoustics and making real-time adjustments.

Another notable characteristic of the DTR-4.6 is its user-friendly interface. The intuitive on-screen setup and configuration guide make it easy to get started, even for those who may not be tech-savvy. The receiver comes with a convenient remote control, and users can also control it via a mobile app, adding a layer of convenience for modern homeowners.

Finally, the design of the DTR-4.6 is both sleek and functional. Its understated aesthetic, coupled with a solid build, ensures it serves as an attractive centerpiece in any home theater setup. The integration of high-quality components further solidifies its reputation as a durable and reliable choice for audiophiles and home cinema enthusiasts alike.

In conclusion, the Integra DTR-4.6 stands as a testament to the brand's commitment to audio excellence, offering a powerful combination of features, cutting-edge technology, and user-centric design that elevates the home entertainment experience to new heights.
Top Page Image Contents