Integra DTR-4.6 instruction manual Troubleshooting

Page 77

DTR-4.6.book Page 77 Thursday, September 22, 2005 1:45 PM

Troubleshooting

If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact the dealer from whom you purchased.

Power

Can’t turn on the AV receiver

•Make sure that the power cord is plugged into the wall outlet properly.

•Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again.

The AV receiver turns off as soon as it’s turned on

•The amp protection circuit has been activated. Remove the power cord from the wall outlet immedi- ately. Disconnect all speaker cables and input sources, and leave the AV receiver with its power cord discon- nected for 1 hour. After that, reconnect the power cord and set the volume to maximum. If the AV receiver stays on, set the volume to minimum, disconnect the power cord, and reconnect your speakers and input sources. If the AV receiver turns off when you set the volume to maximum, disconnect the power cord, and contact the dealer from whom you purchased.

Audio

There’s no sound or it’s very quiet

•Make sure that the digital input source is selected properly (page 40).

•Make sure that all audio connecting plugs are pushed in all the way (page 22).

•Make sure that the polarity of the speaker cables is correct, and that the bare wire is in contact with metal part of each speaker terminal (page 19)

•Make sure that the speaker cables are not shorting.

•Check the volume (page 42). The AV receiver is designed for home theater enjoyment and has a wide volume range for precise adjustment.

•If the MUTING indicator is shown on the display, press the remote controller’s [Muting] button to unmute the AV receiver (page 50).

•While a pair of headphones is connected to the Phones jack, no sound is output by the speakers (page 51).

•Check the digital audio output settings on the con- nected device. On some games consoles, such as those that can play DVDs, the default setting is off.

•With some DVD-Video discs, you need to select an audio format from a menu.

•If your turntable doesn’t have a built-in phono preamp, you must connect one between it and the AV receiver. If your turntable uses an MC cartridge, you must con- nect an MC head amp, or an MC transformer

(page 31).

•Check the speaker settings (pages 36–38).

•The input signal format is set to PCM or DTS. Set it to Auto (page 65).

Only the front speakers produce sound

•When the Stereo listening mode is selected, only the front speakers and subwoofer produce sound.

•In the Mono listening mode, only the front speakers output sound when the Output Sp setting is set to Front (page 59).

•Make sure the speakers are conﬁgured correctly (pages 36, 37).

Only the center speaker produces sound

•If you use the Pro Logic II Movie or Pro Logic II Music listening mode with a mono source, such as an AM radio station or mono TV program, the sound is concentrated in the center speaker.

•In the Mono listening mode, only the center speaker outputs sound when the Output Sp setting is set to Center (page 59).

•Make sure the speakers are conﬁgured correctly (pages 36, 37).

The surround speakers produce no sound

•When the Stereo or Mono listening mode is selected, the surround speakers produce no sound.

•Depending on the source and current listening mode, not much sound may be produced by the surround speakers. Try selecting another listening mode.

•Make sure the speakers are conﬁgured correctly (pages 36, 37).

•When the ZONE 2 SPEAKERS terminals are used, playback in the main room is reduced to stereo (page 66).

The center speaker produces no sound

•When the Stereo listening mode is selected, the center speaker produces no sound.

•In the Mono listening mode, only the front speakers output sound when the Output Sp setting is set to Front (page 59).

•Make sure the speakers are conﬁgured correctly (pages 36, 37).

The subwoofer produces no sound

•When you play source material that contains no infor- mation in the LFE channel, the subwoofer produces no sound.

•Make sure the speakers are conﬁgured correctly (pages 36, 37).

77

Image 77

Contents DTR-4.6 Avis Important Safety InstructionsPower PrecautionsSpeaker cable labels Supplied AccessoriesMake sure you have the following accessories Contents Features Using the Remote Controller Before Using the AV receiverInstalling the Batteries Front Panel Getting to Know the AV ReceiverDisplay Getting to Know the AV ReceiverComponent Video in 1, 2, Rear PanelXM antenna IR in A/B and OUTThis jack is for connecting a powered subwoofer These terminal posts are for connecting speakers in ZoneVideo 1 IN/OUT and Video 2 IN/OUT FRONT, CENTER, and Surround SpeakersReceiver/Tape Mode Remote ControllerAbout the Remote Controller Modes Remote Controller DVD Mode CD, MD, and CDR Modes HDD Mode Enjoying Home Theater Connecting Your SpeakersConnecting Your Speakers Connecting Your SpeakersStrip about 5/8 Speaker Connection PrecautionsConnecting the Speaker Cables Connecting the AM Loop Antenna Connecting AntennaConnecting the Indoor FM Antenna Attach the FM antenna, as shownConnecting an Outdoor FM Antenna Connecting AntennaConnecting an Outdoor AM Antenna Using a TV/FM Antenna SplitterAbout AV Connections Connecting Your ComponentsOptical Digital Jacks AV Connection Color CodingConnecting Audio and Video Signals to the AV Receiver Connecting Your ComponentsWhich Connections Should I Use? Video Connection FormatsVideo Connection Connecting a TV or ProjectorAudio Connection HintOr the other Connecting a DVD playerHooking Up the Multichannel DVD Input DVD recorder Connecting a VCR or DVD Recorder for PlaybackConnecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc CD player Connecting a CD PlayerStep Phono preamp Connecting a TurntableTurntable without a Built-in Phono Preamp Connecting a Cassette, CDR, MiniDisc, or DAT Recorder Auto Power On/Standby Connecting ComponentsRemote Control Direct ChangeConnecting the RS232 Port Connecting the Power Cords of Other ComponentsConnecting the Power Cord Standby indicator lights upTurning On the AV Receiver Do the speaker setup-this is essentialTurning On and Standby Smooth Operation in a Few Easy StepsSpeaker Setup First Time SetupSpeaker Setup menu appears Main menu appears onscreenSubwoofer Mode First Time SetupCrossover Speaker DistanceSpeaker Level Calibration Repeat so that the volumeTest tone from each Speaker is the sameLowed by the Setup button Component Video SetupInput selector Default assignment Press the Receiver button, folButtons to select 2. Digital Digital Audio Input SetupInput, and then press Enter Digital Input menu appearsChanging the Input Display See Using the Listening Modes on Select a listening mode and enjoyPlaying Your AV Components Basic AV Receiver OperationListening to the Radio Tuning into AM/FM Radio StationsListening to AM/FM Stations Displaying AM/FM Radio InformationListening to the Radio Connecting the XM AntennaListening to XM Satellite Radio Signing Up for XM Satellite RadioChannels cannot be selected while Indicator Channel Search modeSelecting XM Radio Channels Use the Up and Down Buttons to select a channelButtons to select a chan Displaying XM Radio InformationNel Displaying XM Information on Your TVXM Radio Messages Positioning the XM AntennaSelecting Presets Presetting AM/FM StationsDeleting Presets XM ChannelsUsing the Multichannel DVD Input Using the Multichannel DVD InputMultichannel DVD Input Settings Subwoofer SensitivitySetting the Display Brightness Adjusting Speaker LevelsCommon Functions Muting the AV ReceiverUsing Headphones Using the Sleep TimerCommon Functions Displaying Source InformationSelecting with the Remote Controller Using the Listening ModesSelecting the Listening Modes Selecting on the AV ReceiverDSP Using the Listening ModesUse this mode with any stereo movie e.g., TV, DVD, VHS Use this mode with any stereo or TV, DVD, VHSAbout the Listening Modes Onkyo Original DSP ModesRecording the Input Source RecordingRecording Audio and Video from Separate Sources Submenu Main menu Onscreen Setup MenusAbout the Onscreen Setup Menus Audio Adjust Menu Adjusting the Listening ModesUsing the Cine Filter Function Adjust, and then press EnterTone Control Settings Adjusting the Listening ModesPL II and Neo6 Settings PL II Music 2 ch only Neo6 MusicMono/Multiplex Settings Dolby Digital SettingsLFE Level Setting MultiplexListening Mode Preset menu Appears Default Listening ModesMode Preset, and then press Use the Up and Down Buttons to select 5. ListeningDelay Advanced SetupInput Setup IntelliVolume Advanced SetupVolume Setup Preferences12V Trigger A/B/C Setup OSD SetupLock Setup OSD PositionChanging the AV Receiver’s Remote ID Changing the Remote Controller’s IDRemote IDs Opt or coax, and then press Digital Input Signal FormatsThat’s assigned to a digital input Using Another Amp in Zone Connecting ZoneUsing Only Speakers in Zone ZoneZone 2 Out Setting Powered Zone 2 SettingControlling Zone 2 from the AV Receiver Using ZoneControlling Zone 2 with the Remote Controller Zone 2 Remote Mode but On the remote controller, pressTo adjust Ton, and then use the LevelRepeat this step as necessary for each setting Using the 12V Triggers in Zone 2 and the Main RoomDelay 12V Trigger Setting for Each Input SourceUsing a Multiroom Kit with Other Components Using a Multiroom Kit with a CabinetUsing a Multiroom Kit with Zone Controlling Other Components Entering Remote Control CodesRemote Control Codes for Integra Components Connected via Resetting the Remote ControllerResetting the Remote Mode Buttons Controlling Other ComponentsCH +/-, TV CH + On, Standby, TVPrev CH TV InputLearning Commands from Other Remote Controllers Making Macros Using MacrosRunning Macros Deleting MacrosTroubleshooting Troubleshooting Can’t learn commands from another remote controller Remote controller doesn’t workSound changes when I connect my head- phones Can’t control other componentsAmpliﬁer Section SpeciﬁcationGeneral Video Section

DTR-4.6 specifications

The Integra DTR-4.6 is an advanced multi-channel A/V receiver, designed to deliver an immersive audio and video experience. Renowned for its high-quality construction and cutting-edge technology, this receiver stands out in today’s competitive home theater market.

One of the main features of the DTR-4.6 is its powerful amplification system. It offers a robust 100 watts of power per channel across seven channels, ensuring that even the most demanding audio tracks are handled effortlessly. The receiver is equipped with Integra's proprietary technology which allows for dynamic power distribution, providing listeners with an impactful audio experience without distortion.

In terms of connectivity, the DTR-4.6 boasts a comprehensive range of options. It includes multiple HDMI inputs that support 4K video pass-through, allowing users to connect their latest devices effortlessly. Additionally, the receiver features various analog and digital inputs, ensuring compatibility with a wide range of audio sources, including CD players, turntables, and streaming devices.

For those who prioritize high-resolution audio, the DTR-4.6 supports several advanced formats, including Dolby Atmos and DTS:X. These immersive audio technologies allow sound to move above and around the listener, creating an unparalleled 3D sound experience that enhances movies, games, and music. Furthermore, the receiver features Advanced MultEQ XT room correction technology, which helps optimize sound quality by analyzing the room's acoustics and making real-time adjustments.

Another notable characteristic of the DTR-4.6 is its user-friendly interface. The intuitive on-screen setup and configuration guide make it easy to get started, even for those who may not be tech-savvy. The receiver comes with a convenient remote control, and users can also control it via a mobile app, adding a layer of convenience for modern homeowners.

Finally, the design of the DTR-4.6 is both sleek and functional. Its understated aesthetic, coupled with a solid build, ensures it serves as an attractive centerpiece in any home theater setup. The integration of high-quality components further solidifies its reputation as a durable and reliable choice for audiophiles and home cinema enthusiasts alike.

In conclusion, the Integra DTR-4.6 stands as a testament to the brand's commitment to audio excellence, offering a powerful combination of features, cutting-edge technology, and user-centric design that elevates the home entertainment experience to new heights.