Integra DTR-4.6 Adjusting the Listening Modes, Tone Control Settings, Neo6 Music

Page 58

DTR-4.6.book Page 58 Thursday, September 22, 2005 1:45 PM

Adjusting the Listening Modes—Continued

Tone Control Settings

You can adjust the bass and treble for the front speakers. The tone control circuits are bypassed in the Direct lis- tening mode.

■Bass

You can boost or cut low-frequency sounds output by the front speakers from –10 dB to +10 dB in 1 dB steps.

■Treble

You can boost or cut high-frequency sounds output by the front speakers from –10 dB to +10 dB in 1 dB steps.

Setting the Bass and Treble on the AV Receiver:

Note:

The AV receiver’s Tone buttons cannot be used in the Direct listening mode.

1 2

1

Press the AV receiver’s [Tone]

 

 

button repeatedly to select either

 

Bass or Treble.

2

Use the Tone [–]/[+] buttons to

 

 

adjust.

PL II and Neo:6 Settings

PL II Music (2 ch only)

These settings only apply to 2-channel (stereo) sources.

■Panorama

With this setting, you can broaden the width of the front stereo image when using the Pro Logic II Music listen- ing mode.

On: Panorama function on.

Off: Panorama function off (default).

■Dimension

With this setting, you can move the sound field forward or backward when using the Pro Logic II Music listening mode. The default value is 3. Higher settings move the sound field forward. Lower settings move it backward. It can be adjusted from 0 to 6.

If the stereo image feels too wide, or there’s too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like it’s in mono, or there’s not enough surround sound, move it backward.

■Center Width

With this setting, you can adjust the width of the sound from the center speaker when using the Pro Logic II Music listening mode. Normally if you’re using a center speaker, the center channel sound is output by only the center speaker. (If you’re not using a center speaker, the center channel sound will be distributed to the front left and right speakers to create a phantom center). This set- ting adjusts the front left, right, and center mix, allowing you to adjust the weight of the center channel sound. It can be adjusted from 0 to 7 (default value is 3).

Neo:6 Music

■Center Image

The DTS Neo:6 Music listening mode creates 5.1-chan- nel surround sound from 2-channel (stereo) sources. With this setting, you can specify by how much the front left and right channel output is attenuated in order to cre- ate the center channel. It can be adjusted from 0 to 5 (default value is 3). This setting is unavailable if no sur- round speakers are connected.

When set to 0, the front left and right channel output is attenuated by half (–6 dB), giving the impression that the sound is located centrally. This setting works well when the listening position is considerably off center. When set to 5, the front left and right channels are not attenu- ated, maintaining the original stereo balance.

58

Page 57 Page 59
Image 58
Page 57 Page 59
Contents DTR-4.6 Important Safety Instructions AvisPrecautions PowerMake sure you have the following accessories Supplied AccessoriesSpeaker cable labels Contents Features Installing the Batteries Before Using the AV receiverUsing the Remote Controller Getting to Know the AV Receiver Front PanelGetting to Know the AV Receiver DisplayXM antenna Rear PanelComponent Video in 1, 2, IR in A/B and OUTVideo 1 IN/OUT and Video 2 IN/OUT These terminal posts are for connecting speakers in ZoneThis jack is for connecting a powered subwoofer FRONT, CENTER, and Surround SpeakersAbout the Remote Controller Modes Remote ControllerReceiver/Tape Mode Remote Controller DVD Mode CD, MD, and CDR Modes HDD Mode Connecting Your Speakers Enjoying Home TheaterConnecting Your Speakers Connecting Your SpeakersConnecting the Speaker Cables Speaker Connection PrecautionsStrip about 5/8 Connecting the Indoor FM Antenna Connecting AntennaConnecting the AM Loop Antenna Attach the FM antenna, as shownConnecting an Outdoor AM Antenna Connecting AntennaConnecting an Outdoor FM Antenna Using a TV/FM Antenna SplitterOptical Digital Jacks Connecting Your ComponentsAbout AV Connections AV Connection Color CodingWhich Connections Should I Use? Connecting Your ComponentsConnecting Audio and Video Signals to the AV Receiver Video Connection FormatsAudio Connection Connecting a TV or ProjectorVideo Connection HintConnecting a DVD player Or the otherHooking Up the Multichannel DVD Input Connecting a VCR or DVD Recorder for Playback DVD recorderConnecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Step Connecting a CD PlayerCD player Turntable without a Built-in Phono Preamp Connecting a TurntablePhono preamp Connecting a Cassette, CDR, MiniDisc, or DAT Recorder Remote Control Connecting ComponentsAuto Power On/Standby Direct ChangeConnecting the Power Cord Connecting the Power Cords of Other ComponentsConnecting the RS232 Port Standby indicator lights upTurning On and Standby Do the speaker setup-this is essentialTurning On the AV Receiver Smooth Operation in a Few Easy StepsSpeaker Setup menu appears First Time SetupSpeaker Setup Main menu appears onscreenCrossover First Time SetupSubwoofer Mode Speaker DistanceTest tone from each Repeat so that the volumeSpeaker Level Calibration Speaker is the sameInput selector Default assignment Component Video SetupLowed by the Setup button Press the Receiver button, folInput, and then press Enter Digital Audio Input SetupButtons to select 2. Digital Digital Input menu appearsChanging the Input Display Playing Your AV Components Select a listening mode and enjoySee Using the Listening Modes on Basic AV Receiver OperationListening to AM/FM Stations Tuning into AM/FM Radio StationsListening to the Radio Displaying AM/FM Radio InformationListening to XM Satellite Radio Connecting the XM AntennaListening to the Radio Signing Up for XM Satellite RadioSelecting XM Radio Channels Channel Search modeChannels cannot be selected while Indicator Use the Up and Down Buttons to select a channelNel Displaying XM Radio InformationButtons to select a chan Displaying XM Information on Your TVPositioning the XM Antenna XM Radio MessagesDeleting Presets Presetting AM/FM StationsSelecting Presets XM ChannelsMultichannel DVD Input Settings Using the Multichannel DVD InputUsing the Multichannel DVD Input Subwoofer SensitivityCommon Functions Adjusting Speaker LevelsSetting the Display Brightness Muting the AV ReceiverCommon Functions Using the Sleep TimerUsing Headphones Displaying Source InformationSelecting the Listening Modes Using the Listening ModesSelecting with the Remote Controller Selecting on the AV ReceiverUsing the Listening Modes DSPAbout the Listening Modes Use this mode with any stereo or TV, DVD, VHSUse this mode with any stereo movie e.g., TV, DVD, VHS Onkyo Original DSP ModesRecording Audio and Video from Separate Sources RecordingRecording the Input Source About the Onscreen Setup Menus Onscreen Setup MenusSubmenu Main menu Using the Cine Filter Function Adjusting the Listening ModesAudio Adjust Menu Adjust, and then press EnterPL II and Neo6 Settings PL II Music 2 ch only Adjusting the Listening ModesTone Control Settings Neo6 MusicLFE Level Setting Dolby Digital SettingsMono/Multiplex Settings MultiplexMode Preset, and then press Default Listening ModesListening Mode Preset menu Appears Use the Up and Down Buttons to select 5. ListeningInput Setup Advanced SetupDelay Volume Setup Advanced SetupIntelliVolume PreferencesLock Setup OSD Setup12V Trigger A/B/C Setup OSD PositionRemote IDs Changing the Remote Controller’s IDChanging the AV Receiver’s Remote ID That’s assigned to a digital input Digital Input Signal FormatsOpt or coax, and then press Using Only Speakers in Zone Connecting ZoneUsing Another Amp in Zone ZonePowered Zone 2 Setting Zone 2 Out SettingControlling Zone 2 with the Remote Controller Using ZoneControlling Zone 2 from the AV Receiver To adjust On the remote controller, pressZone 2 Remote Mode but Ton, and then use the LevelDelay Using the 12V Triggers in Zone 2 and the Main RoomRepeat this step as necessary for each setting 12V Trigger Setting for Each Input SourceUsing a Multiroom Kit with Zone Using a Multiroom Kit with a CabinetUsing a Multiroom Kit with Other Components Entering Remote Control Codes Controlling Other ComponentsResetting the Remote Mode Buttons Resetting the Remote ControllerRemote Control Codes for Integra Components Connected via Controlling Other ComponentsPrev CH On, Standby, TVCH +/-, TV CH + TV InputLearning Commands from Other Remote Controllers Running Macros Using MacrosMaking Macros Deleting MacrosTroubleshooting Troubleshooting Sound changes when I connect my head- phones Remote controller doesn’t workCan’t learn commands from another remote controller Can’t control other componentsGeneral SpecificationAmplifier Section Video Section

DTR-4.6 specifications

The Integra DTR-4.6 is an advanced multi-channel A/V receiver, designed to deliver an immersive audio and video experience. Renowned for its high-quality construction and cutting-edge technology, this receiver stands out in today’s competitive home theater market.

One of the main features of the DTR-4.6 is its powerful amplification system. It offers a robust 100 watts of power per channel across seven channels, ensuring that even the most demanding audio tracks are handled effortlessly. The receiver is equipped with Integra's proprietary technology which allows for dynamic power distribution, providing listeners with an impactful audio experience without distortion.

In terms of connectivity, the DTR-4.6 boasts a comprehensive range of options. It includes multiple HDMI inputs that support 4K video pass-through, allowing users to connect their latest devices effortlessly. Additionally, the receiver features various analog and digital inputs, ensuring compatibility with a wide range of audio sources, including CD players, turntables, and streaming devices.

For those who prioritize high-resolution audio, the DTR-4.6 supports several advanced formats, including Dolby Atmos and DTS:X. These immersive audio technologies allow sound to move above and around the listener, creating an unparalleled 3D sound experience that enhances movies, games, and music. Furthermore, the receiver features Advanced MultEQ XT room correction technology, which helps optimize sound quality by analyzing the room's acoustics and making real-time adjustments.

Another notable characteristic of the DTR-4.6 is its user-friendly interface. The intuitive on-screen setup and configuration guide make it easy to get started, even for those who may not be tech-savvy. The receiver comes with a convenient remote control, and users can also control it via a mobile app, adding a layer of convenience for modern homeowners.

Finally, the design of the DTR-4.6 is both sleek and functional. Its understated aesthetic, coupled with a solid build, ensures it serves as an attractive centerpiece in any home theater setup. The integration of high-quality components further solidifies its reputation as a durable and reliable choice for audiophiles and home cinema enthusiasts alike.

In conclusion, the Integra DTR-4.6 stands as a testament to the brand's commitment to audio excellence, offering a powerful combination of features, cutting-edge technology, and user-centric design that elevates the home entertainment experience to new heights.
Top Page Image Contents