Integra DTR-5.2 appendix

Page 43

Programming the commands of remote controllers for other devices into the remote controller

4.Press and hold down the button (that corresponds to the command you are programming) on the remote controller of the other device until the SEND/LEARN lamp on the remote controller flashes twice.

After flashing twice, the SEND/LEARN indicator will light again.

5.Repeat Steps 3 and 4 to transfer all the commands you desire from the other remote controller and program them to buttons on the remote controller under the same MODE.

Repeat Steps 2 through 4 to program commands to a different MODE (e.g., when programming from a different remote controller).

6.Press the MODE button that you pressed in step 2 to complete the programming.

7.Operate the newly programmed buttons to make sure the learning function was performed properly.

Notes:

•The remote controller codes for Integra/Onkyo compact disc players, cassette tape decks, DVD players, and mini disc recorder have already been programmed into buttons on the remote controller. You may, however, use these buttons to program the codes for other remote controllers. If you wish to restore the Integra/Onkyo preset codes after you program new codes, you must first erase the new codes (see page 44).

•The remote controller has 408 memory slots (8 modes ⋅ 51 buttons). Some remote controllers may have more commands that can be remembered by the remote controller. In such cases, it will be necessary for you to determine which commands are more important than others.

•If no button is pressed for more than 30 seconds during the programming, or if you perform an invalid operation during programming, the SEND/LEARN indicator flashes three times quickly, and the remote controller exits the programming mode. Resume from Step 2.

•If a failure occurs during programming, the SEND/LEARN indicator flashes three times quickly, and the remote controller exits the programming mode. Resume from Step 3.

•If a failure occurs five times in row during programming, the remote controller exits the programming mode. Resume from Step 3.

•If you try to program beyond the learning capacity of the remote controller, the SEND/LEARN indicator flashes six times quickly, and the remote controller exits the programming mode. Try programming under a different MODE button.

•When you want to program a command to a button to which you have already programmed a command, simply follow the same procedure given and programming for that button will be overwritten.

•The remote controller uses infrared rays to send its commands, as do most other remote controllers. Though most remote controller codes can be memorized by the remote controller, be aware that some remote controllers use a system that is quite different from the remote controller and therefore may not be able to be programmed.

•Some remote controllers have a single button that performs multiple functions (for example, the function may change each time the button is pressed). If this is the case, each function must be programmed to a separate button on the remote controller.

•Once you have transferred the commands from the other remote controller, refer to the instruction manual that came with that product for instructions on how to operate that product.

•Make sure both the remote controller and the other remote controller have new batteries. If either of them has batteries that are low, you may not be able to program the commands of the other remote controller properly into the remote controller.

See page 48 for how to erase the memorized commands from all buttons.

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents DTR-5.2 Avis Important SafeguardsPrecautions Supplied accessories FeaturesInstalling the remote controller batteries Before using this unitUsing the remote controller Front panel display Sleep indicatorFront panel facilities Front panelFront panel facilities Remote controller Remote controller Connections Coax Coaxial OPT Optical No settingAC Inlet Connections Connecting your audio componentsConnecting a turntable Phono Connecting a compact disc player CDConnecting a video cassette recorder Video Connecting your video componentsFlow of the video signals is as follows Connecting a DVD player DVDPower cord supplied To an AC wall outlet Connecting a television monitor or projector12V Trigger terminal Direct change function Power on/ready functionPower off function Connect to devices with z terminalsIR OUT Other componentConnecting a subwoofer Connecting speakersStandard speaker placement Connecting the speaker cableConnecting speakers Connecting speakersConnecting the power Assembling the AM loop antenna Connecting antennasConnecting the AM antenna cable Connecting the included antennasDirectional linkage Connecting antennasConnecting an FM outdoor antenna Connecting an AM outdoor antennaSpeaker Configuration Speaker setupReturn Setup Enter Speaker Distance Speaker setupLevel Calibration FM AM Listening to a stereo radio station FM modeTuning into a radio station Listening to Radio BroadcastsErasing a preset radio station Presetting a radio station Selecting a preset radio stationListening to Radio Broadcasts Enjoying music or videos with the DTR-5.2 Selecting a listening modeBasic operation Enjoying music or videos with the DTR-5.2 Temporarily changing the speaker output levels Changing the audio modeEnjoying the multichannel input Listening modes Using listening modeListening Mode Preset Input SetupAudio Setup Audio Setup procedureInput Setup Controller to set 12V Trigger IntelliVolume12V Trigger Turn the jog dial or pressPreference Volume SetupHeadphones Level Late Night SetupRecording an audio source RecordingPress the desired operation button Using remote controllerCalling up a preset radio station Controlling an Integra/Onkyo cassette tape deckControlling an Integra/Onkyo CD player Using remote controllerPress the CD Mode button Disc Stdby CD ModeControlling an Integra/Onkyo DVD player Press the DVD Mode buttonREC/R Record SAT, CABLE, VCR, and TV Mode buttonsPress the MD Mode button Controlling an Integra/Onkyo MD recorderLearning a pre-programming code When entering the code of Integra/Onkyo DVD playersSEND/LEARN indicator Learning a pre-programming codePre-programmong codes Learning a pre-programming codeCable Mode Cable Mode Operating your programmed remote controllerDVD Mode DVD Player Mode SAT Mode Satellite Tuner ModePress the VCR Mode button Operating your programmed remote controllerVCR Mode VCR Mode TV Mode TV ModeLight Programming procedureMode Direct Mode Macro SEND/LEARNPage SEND/LEARN indicator Mode buttons Erasing the programmed command from one buttonErasing all the commands programmed under a Mode button Press and release the same Mode button againRunning a Macro function Using a Macro functionPress the Mode Macro button to complete the programming Programming a Macro functionProgramming the Direct Macro function Using a Macro functionRunning a Direct Macro function Erasing a direct macro from the Direct Macro button Erasing a macro from the Mode Macro buttonPress the Mode Macro button again Direct Macro Mode buttonsOperation Erasing all commands and macros that have been programmedMacro mode programming memo Press the Enter buttonTuner Section Remote ControllerGeneral Troubleshooting guide Video and Audio Troubleshooting guideIf one of the messages shown below appears Onkyo U.S.A. Corporation

DTR-5.2 specifications

The Integra DTR-5.2 is a notable A/V receiver that combines high-performance audio capabilities with versatile connectivity options, making it a preferred choice for home theater enthusiasts. It is designed to deliver a rich, immersive audio experience, while also supporting the latest in video technologies.

At the heart of the DTR-5.2 is its advanced audio processing capabilities. It features Dolby Atmos and DTS:X support, allowing users to experience three-dimensional soundscapes that immerse them in their favorite movies and music. With these formats, sound moves in all directions, enhancing the realism of the audio experience, especially in large home theater setups.

Another significant feature of the DTR-5.2 is its ability to decode various audio formats, including high-resolution audio from sources like Blu-ray discs and streaming services. The receiver supports formats like DSD, FLAC, and ALAC, ensuring that audiophiles can enjoy their music at the highest quality possible. The integration of technologies like zone 2 or zone 3 functionality allows for multi-room audio setups, providing flexibility in how and where music can be enjoyed in the home.

The DTR-5.2 also offers extensive connectivity options. It comes equipped with multiple HDMI inputs and one output, supporting 4K Ultra HD video and HDR (High Dynamic Range) for a stunning viewing experience. It includes features like Audio Return Channel (ARC), which simplifies the connection between the receiver and compatible TVs, streamlining the setup process.

With its user-friendly interface, the Integra DTR-5.2 allows for effortless navigation and adjustments to settings. The included remote control is intuitive, giving users quick access to settings and presets. Additionally, the receiver is compatible with various control systems, which can be particularly beneficial for sophisticated home automation setups.

In terms of build quality, the DTR-5.2 is designed to last. It features a robust chassis that minimizes interference and optimizes performance. The multi-channel amplifier can provide powerful sound, ensuring that even the most demanding audio demands are met.

Overall, the Integra DTR-5.2 stands out for its combination of cutting-edge audio technologies, user-friendly features, and robust build quality, making it a strong contender for anyone looking to elevate their home entertainment experience.
Top Page Image Contents