Spectra Watermakers MPC-5000 owner manual Spectra High Pressure Tube Fitting Assembly

Page 13

Spectra High Pressure Tube Fitting Assembly

Use ONLY Dayco Imperial Nylo-Seal 88-NSR-1/2 tubing for high pressure connections.

Carefully fit and measure the tubing before cutting with a sharp razor knife or hose cutter and remove any burrs. Minimum tubing bend radius is 6”. Route tubing away from excessive heat sources and secure from vibration and chafe. Have at least one shallow bend in the tube assembly after it is installed.

Refer to figure 1. If a fitting has been dissembled, reassemble as illustrated. The notch on the ferrule must engage the inside of the nut properly for the nut to seat down fully. Once the tube is inserted the ferrule and nut will naturally align.

Refer to figure 2. Insert tube fully into the fitting, it should go in 0.9”. Tighten the nut finger tight while moving the tube around to prevent binding. One thread should be showing under the nut. Secure the tube so it won’t back out when tightening.

Refer to figure 3. Use 13/16” wrench to hold a straight body fitting or a 3/4” wrench for a 90º body, and a 7/8” wrench for the nut. Hold the body, recheck the tube insertion, then tighten the nut 1-1/4 turns. Use the index mark on the nut as a guide. The threads should be completely covered by the nut.

Make sure these fittings are tight on initial assembly or they will fail!

The correct torque is specification is 85 foot pounds

Figure 1.

Figure 2.

Index mark

Straight thread

Straight or 90 deg.

 

 

3/8" pipe thread

NutFerruleBody

Nut finger tight with 1 thread showing

Cut tube square

Black high pressure tubing

Tighten 1-2/3 turns (10 flats of the

 

nut) with a7/8" wrench after finger tight.

 

Use index mark as guide

No threads showing

Figure 3.

Insert tube 0.9" until it stops

IMPORTANT!

 

 

Hold fitting body with

a

 

wrench when tightening

13

Image 13
Contents Page Page Table of Contents Page Water to get safely into your next port Introduction to the Ventura 150 MPCVentura MPC Shipping List Getting StartedWiring Installation BasicsRead the directions Thru-hullsSea Strainer, Mount with Ventura 150 MPC PlumbingFeed Pump Relocation Product to tank Product Water PlumbingBody Nut Dissemble fitting components Tubing Max Product Tube Fitting AssemblyMembrane Pressure Vessel Relocation Correct torque is specification is 85 foot pounds Spectra High Pressure Tube Fitting AssemblyTotal length for a pair of wires MPC-5000 WiringClark Pump Harness Tank Switch Installation and Operation Page Ventura MPC New System Start-Up and Testing Page Salinity MPC Display ModesVentura MPC Dry Testing With Artificial Ocean Ventura MPC Operation Normal operation Automatic Store Cycle Flush Cycle AdjustmentManual Automatic Operation Manual OperationSystem Storage or Pickling Long Term Storage ProceduresClean Up Ventura MPC Storage ProcedureWinterizing Seawater Strainer Maintenance GeneralPrefilters Oil Water Separator OptionalMembranes Membrane CleaningDo not Close the pressure relief valve Cleaning ProcedureSpectra Watermakers recommended spare parts Suggested Spares Ventura MPCVentura MPC Troubleshooting Procedures Error Messages Accumulator Pressure OP-2 BAD Smelling Product Water OP-3 Chemicals OP-4 Fresh Water Flush PF-3 PREFILTERS- ShurFlo SF-1 Shurflo Pump WON’T RUN SF-2 Adjust Shurflo Pressure Switch HS LF-1 Poor Product Quality HS LF-2 Flow TEST/ Shurflo Brane Operation Manual Brane Power Harness Do not Disconnect Or Splice ANY High Voltage Wiring Part Numbers PL-TEE-1/2FN Part NumbersPL-CKV-1/4M-F PL-NLT-1/2HP EL-FP-FPHS Clark Pump Front View Reversing Valve End Blocks Parts Center BlockCylinder Assembly

MPC-5000 specifications

The Spectra Watermakers MPC-5000 is a highly efficient water desalination system designed for a variety of applications, including marine, off-grid, and emergency situations. Known for its reliability and innovative technology, the MPC-5000 stands out as one of the leading solutions for producing fresh water from saltwater.

One of the main features of the MPC-5000 is its impressive production capacity. Capable of producing up to 5,000 gallons of fresh water per day, this system is well-suited for larger vessels or facilities with significant water needs. This robust output makes it an ideal choice for yachts, research vessels, and even small communities in remote areas.

The MPC-5000 utilizes advanced reverse osmosis technology, a process that efficiently separates salt and impurities from seawater. This technique not only ensures high-quality drinking water but also operates at lower energy consumption compared to traditional desalination methods. By employing a state-of-the-art energy recovery device, the MPC-5000 maximizes energy efficiency, significantly reducing operational costs and environmental impact.

In terms of build quality, the MPC-5000 is constructed with marine-grade materials to withstand harsh conditions, making it durable and reliable for long-term use. Its compact design allows easy installation on various platforms, and the system can be operated either through AC or DC power sources, providing flexibility for diverse applications.

The onboard controls of the MPC-5000 are user-friendly, featuring a digital display that provides real-time data on system performance, water production rates, and maintenance alerts. This intuitive interface simplifies operation and monitoring, ensuring users can quickly identify and address any issues.

Another noteworthy characteristic is its low maintenance requirement. The MPC-5000 is designed for easy serviceability, allowing users to conduct routine maintenance with minimal downtime. The integrated filtration system and user-replaceable membrane further enhance its appeal, offering convenience without sacrificing performance.

In conclusion, the Spectra Watermakers MPC-5000 is a standout solution in the water desalination market. With its impressive production capacity, advanced technology, durable construction, and user-friendly design, it meets the water needs of various users while ensuring efficient and reliable operation. Whether for marine use, emergencies, or off-grid living, the MPC-5000 represents a smart investment in sustainable water sourcing.