Spectra Watermakers MPC-5000 owner manual HS LF-1 Poor Product Quality

Page 41

HS LF-1 POOR PRODUCT QUALITY

With any product water quality issue, you need to check the calibration of the salinity tester that you are using before proceeding.

Membranes are not an exact science and two identical systems can have a different product quality result. World health standards deem water of up to 1000 PPM of total dissolved solids acceptable for drinking consumption. We consider any thing below 700 PPM acceptable but not ideal, and anything below 500 PPM excellent. Factors that could affect water quality are addressed below.

LOW SYSTEM FLOW OR PRESSURE will equate to lower product quality (higher PPM). A 200-C system running at 70 psi will deliver product water in the 400- 500 PPM range, while the 380-C systems with twice the flow and operating at 100 psi into the same size membrane, will produce 200-300 PPM water. Ventura 150 systems, which have a higher feed to output pressure ratio (See MISC-4 nominal pressures), as well as a higher feed flow/membrane area ratio, will produce water in the 150-200 PPM range. These improvements in product quality come at the expense of energy efficiency.

DAMAGE TO THE MEMBRANE by chlorine contamination. Flushing the system with chlorinated water will irreparably damage the membrane. Charcoal filters are used to absorb any chlorine which might be present in flush water. They must be of proper specification to be suitable. There is no test for chlorine damage except the process of elimination of other causes.

DIRTY OR SCALED membranes. A dirty (foreign material), scaled (mineral deposits), or contaminated (bacterial growth) membrane can result in poor water quality and abnor- mal operating pressures. If operating pressures are above normal, then cleaning is indi- cated. If the system pressures are within operating normal range, cleaning may have little result. Cleaning is no better for a membrane than it is for your clothes. Avoid cleaning as a diagnostic tool.

MECHANICAL LEAKAGE within the membrane pressure vessel. This is an unlikely but possible cause of poor water quality with old style Codeline pressure vessels (white) that we have used in the past. The Spectra pressure vessel has a double O-ring arrange- ment that includes a telltale hole between them so that any salt water leaking past an O-ring will drip into the boat and not go into the product water.

If system flow (product plus brine) is 1.5 GPM or above on one pump, the membrane is clean, the product flows are consistent with the system flow and the water quality is still not accept- able, then replacement of the membrane is indicated. See “HS-LF2 Flow Check” for instruc- tions on checking flow rates

7/6/14

41

Image 41
Contents Page Page Table of Contents Page Water to get safely into your next port Introduction to the Ventura 150 MPCVentura MPC Shipping List Getting StartedWiring Installation BasicsRead the directions Thru-hullsSea Strainer, Mount with Ventura 150 MPC PlumbingFeed Pump Relocation Product to tank Product Water PlumbingBody Nut Dissemble fitting components Tubing Max Product Tube Fitting AssemblyMembrane Pressure Vessel Relocation Correct torque is specification is 85 foot pounds Spectra High Pressure Tube Fitting AssemblyTotal length for a pair of wires MPC-5000 WiringClark Pump Harness Tank Switch Installation and Operation Page Ventura MPC New System Start-Up and Testing Page Salinity MPC Display ModesVentura MPC Dry Testing With Artificial Ocean Ventura MPC Operation Normal operation Automatic Store Cycle Flush Cycle AdjustmentManual Automatic Operation Manual OperationSystem Storage or Pickling Long Term Storage ProceduresClean Up Ventura MPC Storage ProcedureWinterizing Seawater Strainer Maintenance GeneralPrefilters Oil Water Separator OptionalMembranes Membrane CleaningDo not Close the pressure relief valve Cleaning ProcedureSpectra Watermakers recommended spare parts Suggested Spares Ventura MPCVentura MPC Troubleshooting Procedures Error Messages Accumulator Pressure OP-2 BAD Smelling Product Water OP-3 Chemicals OP-4 Fresh Water Flush PF-3 PREFILTERS- ShurFlo SF-1 Shurflo Pump WON’T RUN SF-2 Adjust Shurflo Pressure Switch HS LF-1 Poor Product Quality HS LF-2 Flow TEST/ Shurflo Brane Operation Manual Brane Power Harness Do not Disconnect Or Splice ANY High Voltage Wiring Part Numbers PL-TEE-1/2FN Part NumbersPL-CKV-1/4M-F PL-NLT-1/2HP EL-FP-FPHS Clark Pump Front View Reversing Valve End Blocks Parts Center BlockCylinder Assembly

MPC-5000 specifications

The Spectra Watermakers MPC-5000 is a highly efficient water desalination system designed for a variety of applications, including marine, off-grid, and emergency situations. Known for its reliability and innovative technology, the MPC-5000 stands out as one of the leading solutions for producing fresh water from saltwater.

One of the main features of the MPC-5000 is its impressive production capacity. Capable of producing up to 5,000 gallons of fresh water per day, this system is well-suited for larger vessels or facilities with significant water needs. This robust output makes it an ideal choice for yachts, research vessels, and even small communities in remote areas.

The MPC-5000 utilizes advanced reverse osmosis technology, a process that efficiently separates salt and impurities from seawater. This technique not only ensures high-quality drinking water but also operates at lower energy consumption compared to traditional desalination methods. By employing a state-of-the-art energy recovery device, the MPC-5000 maximizes energy efficiency, significantly reducing operational costs and environmental impact.

In terms of build quality, the MPC-5000 is constructed with marine-grade materials to withstand harsh conditions, making it durable and reliable for long-term use. Its compact design allows easy installation on various platforms, and the system can be operated either through AC or DC power sources, providing flexibility for diverse applications.

The onboard controls of the MPC-5000 are user-friendly, featuring a digital display that provides real-time data on system performance, water production rates, and maintenance alerts. This intuitive interface simplifies operation and monitoring, ensuring users can quickly identify and address any issues.

Another noteworthy characteristic is its low maintenance requirement. The MPC-5000 is designed for easy serviceability, allowing users to conduct routine maintenance with minimal downtime. The integrated filtration system and user-replaceable membrane further enhance its appeal, offering convenience without sacrificing performance.

In conclusion, the Spectra Watermakers MPC-5000 is a standout solution in the water desalination market. With its impressive production capacity, advanced technology, durable construction, and user-friendly design, it meets the water needs of various users while ensuring efficient and reliable operation. Whether for marine use, emergencies, or off-grid living, the MPC-5000 represents a smart investment in sustainable water sourcing.