Winix Air Cleaner manual Using the Remote Control

Page 10

REMOTE CONTROL

*5000B does not come with remote a control.

PREPARATION

• Press and slide the back cover of the remote to remove.

• Insert batteries as shown.

• Close the back cover.

BATTERY USE

The batteries for the remote control are for initial use only. Change the batteries when necessary.

When replacing the batteries, replace both at once with 2 new AA batteries.

Incorrect battery usage may cause battery fluid leakage and/or damage.

When not using the remote control for an extended period of time, remove the batteries.

Avoid dropping or damaging the remote control. Keep remote control away from direct sunlight or heaters.

USING THE REMOTE CONTROL

Proper conditions

Operate the remote control facing the air cleaner.

Operate within 20 feet of the air cleaner.

Poor conditions that may impair operation

Any location where there is inverter lighting equipment or electronic spontaneous lighting equipment.

When objects or furniture are located between remote and air cleaner.

When air cleaner unit is located in direct sunlight.

In areas where fluorescent lighting is flickering due to worn out bulbs.

POWER

Use the POWER button to turn the power on and off. A short "beep" will sound when you turn the unit on or off. Once the unit is on, it will automatically switch into Automatic operation. Turn the unit to manual control by pressing one of the FAN CONTROL buttons.

TIMER

This button is used to set the timer. Press the button repeatedly to set the unit to run for 2 or 4 hours or to cancel. Each time you press the button, it will advance to the next pre-set amount of time. The indicator light on the unit will show the remaining amount of time. The unit will stop operating when the set amount of time runs out.

FAN CONTROL

UP

Use this button to switch from Automatic operation and increase the fan speed level.

DOWN

Use this button to decrease the fan speed level.

TURBO

Use this button to switch from Automatic operation and begin the maximum amount of room cleaning and air movement.

AUTO/SLEEP

When unit is first turned on it automatically defaults to auto mode.

Pressing AUTO/SLEEP button once activates Energy Saving mode. (Fan speed will not increase past level three.)

Pressing AUTO/SLEEP button a second time activates Sleep mode. (Fan speed will not increase past level one.)

PLASMA ON/OFF

Use this button to turn the PlasmaWaveTM generator on or off.

9

Image 10
Contents Page Page Package Contents Table of ContentsWarranty Safety InstructionsProduct Specifications Important Instructions for Using Your AIR CleanerAIR Cleaner Features MULTI-STAGE CleaningWashable Carbon Filter 5000 & 5000S AIR Cleaner SET-UPPlasmaWave All FAN Speed Indicator Shows current fan speed setting Display Panel 5000 and 5000SDisplay Panel 5000B Automatic Operation Sleep ModeOperation Manual OperationRemote Control Using the Remote ControlFAN Control Replacement Procedure Care and MaintenanceFilter Cassette Replacement Filter Cleaning 5000 and 5000SDust Sensor Cleaning 5000 and 5000S Solutions to Common Problems TroubleshootingProblem Possible Solution Page Contenido DEL Paquete ÍndiceGarantía Instrucciones DE SeguridadEspecificaciones DEL Producto No manipular el enchufe con las manos mojadasCaracterísticas DEL Purificador DE Aire Montaje DEL Purificador DE Aire Pantalla 5000 y 5000S EL Indicador DE Velocidad Pantalla 5000BCambiar EL Medidor Modo Automático OOperación Manual OperaciónOperación Automática Detectores DE Polvo Y OloresAparato DE Control Remoto Botón Power Botón Turbo Botón AUTO/SLEEP Botón Timer Botones Reemplazo del marco del filtro Cuidado Y MantenimientoLimpieza Procedimiento del recambioLimpieza del detector de polvo 5000 y 5000S Marco DEL FiltroSolución de problemas comunes Resolución DE ProblemasProblema Posible Solución Servicio AL Cliente Asegúrese de mencionar el número del modelo