Yeoman YMMB manual Seasonal use, Troubleshooting tips, Smoke Control kit

Page 11

USER INSTRUCTIONS

15.Seasonal use

15.1Clean and service the appliance if it is not used during the warmer periods of the year, as detailed in the Maintenance and Servicing section.

15.2Set the air controls to 50% to keep the appliance ventilated and stop the build-up of any moisture inside.

15.3Before re-lighting the appliance:

Remove the baffle.

Clear any debris that may have accumulated.

Check the flue is clear of any blockages.

16.Troubleshooting tips

16.1Stove glass blackening

This has four possible causes:

1.Incorrect use of Airwash

See User Instructions, Sections 1, 4 and 5 for the correct use of the air controls.

2.Burning unseasoned wood

See User Instructions, Section 3 to identify when wood is ready for burning.

3.Stove operated at too low a temperature

A stove pipe thermometer can identify this problem (Stovax part no 3046). The ideal working temperature range is 130°C - 250°C (270°F - 480°F). Failing to close down the Primary Air Control once the appliance has heated up to this range may cause the appliance to exceed the ideal temperature range and to over-fire. Over-firing can cause permanent damage to the appliance and invalidates your warranty. Burn with the Airwash Control fully open for approximately 20 minutes to cure this.

The problem may be caused by damping down the appliance during periods of extended burning.

4.Problems with the flue, in particular insufficient air pull. If the flue is not working efficiently the glass can blacken. A flue which has too much downdraft may be too short, needs lining, or has too many bends. This can also cause blackening of the stove glass. Contact the installer or a flue specialist for advice.

16.2Riddling Mechanism Jamming

This occurs when ash builds up under the riddling grate preventing movement. To rectify:

Lift out the riddling mechanism (see Installation Instructions, Section 5) and remove all ash.

Replace riddling mechanism when cleaning is complete.

De-ash and clean the inside of the appliance regularly to avoid build up of ash and subsequent jamming of mechanism.

16.3Glass cracking

Do not over tighten the screws on the glass clamp when replacing the glass. This causes stress and the intense temperature changes can cause the glass to crack. For replacement glass contact your local Yeoman retailer.

16.4Appliance is producing tar

This can be identified by:

A very strong pungent smell shortly after the appliance is lit and heats up.

Glass blackening.

Thick, brown, sticky tar oozing from the pipe joints.

This is caused by burning damp wood and running the appliance at too low a temperature.

Use well seasoned wood and operate the appliance within the ideal temperature range.

Tar is a major cause of chimney fires. If the appliance experiences problems with tar build up consult a chimney sweep before continued use of the appliance.

16.5In the unlikely event of a problem that cannot be solved by these tips contact your installer or retailer for help.

17.SMOKE Control kit

17.1This appliance can be modified to burn wood in a smoke control zone. For more details on the Smoke Control Kit for this appliance contact your retailer.

NOTE: These appliances have been independently tested to PD6434 and approved by DEFRA as an exempted appliance, allowing it to burn wood in Smoke Control areas when fitted with a Smoke Control Kit.

11

Image 11
Contents Models Ymmb Yeoman CL Milner BrickInstallation Instructions Ymmb Appliance Commissioning Checklist User InstructionsInstallation Technical Specification PRE-INSTALLATIONEssential Information Must be completed Appliance Commissioning ChecklistInstallation Engineer Retailer appliance was purchased fromTriple Air Systems For Air Controls see DiagramUser Instructions General PointsDo not touch the paint during the first period of use Using the Appliance for the First TimeIf necessary seek expert advice Use a protected gloved hand to operateWood Logs Recommended FuelsLighting The appliance Burning Solid fuel Air Wash AdjustDo not close the Secondary Air control when burning wood Running The applianceBurning tips Chimney fire ASH RemovalExtended burning OVER-FIRINGCare of stove General CleaningCleaning Glass Chimney SweepingSmoke Control kit Troubleshooting tipsSeasonal use Packing list TECHNICAL SPECIFICATIONStandard features CL Milner Brick103 369 243 282 104 379 156 281 593 520 CL Inset DimensionsSite Requirements Additional Flue or ChimneyMax. Draught = 2.0mm Wg Min. Draught = 1.0mm Wg U.K Flue PlateHearth and appliance. Consult a structural engineer Minimum dimensions HearthFor advice before proceeding Flue Outlet Positions555-560mm Milner Brick OpeningFire surround clearances OpeningModel PRE-INSTALLATION ChecksFlue VentilationFitting Appliances on a boat Ø16mm rope Slide stove into position Installation InstructionsInstalling the Appliance Legal requirementsDo not use appliance without the log guard in position Removal of the doorRemoval of the LOG Guard Removal of the baffleDo not modify the baffle system Lift and rotate the centre grate see Diagram Centre grateRemoval of the Grate Removal of Cast Iron FIREbricks Removal of Cleanburn ChamberCo alarms BS EN 50292 and from the alarm manufacturers instructionsRecord serial number in Appliance Commissioning CommissioningCommissioning Annual Service Fitting a NEW Door Glass Fitting and Removal of BaffleFitting and Removal of the Grate Fitting and Removal of Cast Iron FirebricksJoint Fitting a new door sealBlack face Glass rope Seal Do not over tighten the clamp as this could break the glassHetas Approved Chimney Sweeps Adjusting Door Catch & HingesTo adjust the door hinge plate assembly Do not undo the catch more than 3-4mmSpare Parts Outer Door 10TH Service Service RecordsPage Division of Stovax

YMMB specifications

Yeoman YMMB, short for Yeoman Yet Another Model Builder, is an advanced tool in the realm of web development, particularly known for its capabilities in scaffolding projects and automating repetitive tasks. It serves as a robust generator framework, streamlined to enhance developer productivity by allowing them to focus on coding rather than setting up boilerplate code. Yeoman YMMB is designed for building modern web applications and provides a seamless workflow that integrates various technologies and development practices.

One of the main features of Yeoman YMMB is its powerful scaffolding ability. Developers can easily create a new project structure with just a few commands, generating the essential files and directories needed to kickstart a web application. This feature not only saves time but also ensures that developers adhere to best practices and standards in web development. The intelligent generators available with Yeoman YMMB can create everything from single-page applications to entire web ecosystems.

Yeoman YMMB leverages several modern web technologies that have become industry standards. For instance, it supports popular front-end frameworks like React, Angular, and Vue.js, making it a versatile choice for developers working on diverse projects. Additionally, it comes with built-in support for various CSS preprocessors such as Sass and Less, enhancing the styling process and allowing for more maintainable stylesheets.

Another characteristic of Yeoman YMMB is its emphasis on modularity. The generator ecosystem enables developers to create and share custom generators that can be tailored to specific project requirements. This feature fosters a collaborative environment, as developers can build upon each other’s work, thereby speeding up the development process.

In terms of configuration, Yeoman YMMB offers a flexible setup, allowing developers to integrate with task runners like Gulp and Grunt. This integration enables automation of tasks such as minification, linting, and testing, streamlining the development workflow. With these automation tools, developers can focus more on writing code and less on managing the build process.

Moreover, Yeoman YMMB is community-driven, meaning it benefits from continuous updates and improvements based on user contributions. The active community provides extensive documentation and a plethora of plugins, each designed to enhance functionality and features. Through this collaboration, Yeoman YMMB remains relevant and up-to-date with the latest trends in web development.

In summary, Yeoman YMMB is an essential tool for web developers who seek efficiency and modernization in their workflow. Its scaffolding capabilities, support for modern technologies, modularity, and community-driven enhancements make it a valuable asset in building contemporary web applications.