Yeoman YMMB manual Running The appliance, Burning Solid fuel, Burning Wood, Air Wash Adjust

Page 7

USER INSTRUCTIONS

8

Air Inlets

Log Guard

5.5When in use, burning the appliance at a high temperature for a short period also reduces tars and creosotes.

Warning: Do not operate the appliance with the Primary Air Control open for long periods of time as this could cause over- firing and may cause permanent damage.

5.6Burning Solid fuel:

—Set air controls (see diagram below).

PR9033

—Close the door.

Do not leave the door open as this could over-fire and damage the appliance.

5. Running The appliance

5.1 Burning Wood:

—Close the Primary Air control and use the Airwash to

Air Wash: 50% Open

Primary Air: 100% Open

PR9031

Secondary Air:

Fully Closed

PR9032

control the temperature (see Diagram 9).

9

Air Wash:

Adjust

PR9030

—Wood burns best on a bed of ash (approx. 25mm (1") deep).

—Rake the embers evenly over the firebed and open the Airwash control fully for a few minutes before re-fuelling.

—Do not close the Secondary Air control when burning wood.

5.2Burn new logs at a high temperature for a few minutes before adjusting the Airwash control. Refuel little and often for clean, efficient burning.

5.3Experience establishes settings to suit personal preferences.

5.4Do not burn large amounts of fuel with the Airwash control closed for long periods of time. This reduces the glass cleaning effect and causes tars and creosotes to build-up in the appliance and flue system.

5.7De-ash the firebed before re-fuelling (see User Instructions, Section 7).

Open the Primary Air Control fully to establish a glowing bed before adding new fuel.

Burn new fuel at a high temperature for a few minutes before adjusting the Primary Air Control to the desired setting.

Refuel little and often for clean, efficient burning.

5.8Experience establishes settings to suit personal preference.

5.9Do not burn large amounts of fuel with the Primary Air Control on a low combustion setting for long periods of time. This reduces the glass cleaning effect of the Airwash and causes tars and creosotes to build-up in the appliance and flue system.

5.10When in use, burning the appliance at a high temperature for a short period reduces tars and creosotes.

5.11Only anthracite or smokeless fuels suitable for use in closed appliances must be burned in this appliance.

5.12Do not burn bituminous coal, ‘petro-coke’ or other petroleum based fuels as this invalidates the product guarantee.

5.13Do not load fuel above the log guard and the Secondary Air Inlets at the back of the firebox (see Diagram 8).

—Do not refuel when a large amount of flame is present in the firebox as this could cause smoke or flames to spill into the room.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Models Ymmb Yeoman CL Milner BrickInstallation Instructions Ymmb Appliance Commissioning Checklist User InstructionsInstallation Technical Specification PRE-INSTALLATIONEssential Information Must be completed Appliance Commissioning ChecklistInstallation Engineer Retailer appliance was purchased fromTriple Air Systems For Air Controls see DiagramUser Instructions General PointsDo not touch the paint during the first period of use Using the Appliance for the First TimeIf necessary seek expert advice Use a protected gloved hand to operateLighting The appliance Recommended FuelsWood Logs Burning Solid fuel Air Wash AdjustDo not close the Secondary Air control when burning wood Running The applianceBurning tips Chimney fire ASH RemovalExtended burning OVER-FIRINGCare of stove General CleaningCleaning Glass Chimney SweepingSeasonal use Troubleshooting tipsSmoke Control kit Packing list TECHNICAL SPECIFICATIONStandard features CL Milner BrickSite Requirements CL Inset Dimensions103 369 243 282 104 379 156 281 593 520 Additional Flue or ChimneyMax. Draught = 2.0mm Wg Min. Draught = 1.0mm Wg U.K Flue PlateHearth and appliance. Consult a structural engineer Minimum dimensions HearthFor advice before proceeding Flue Outlet Positions555-560mm Milner Brick OpeningFire surround clearances OpeningModel PRE-INSTALLATION ChecksFlue VentilationFitting Appliances on a boat Ø16mm rope Slide stove into position Installation InstructionsInstalling the Appliance Legal requirementsDo not use appliance without the log guard in position Removal of the doorRemoval of the LOG Guard Removal of the baffleRemoval of the Grate Lift and rotate the centre grate see Diagram Centre grateDo not modify the baffle system Removal of Cast Iron FIREbricks Removal of Cleanburn ChamberCo alarms BS EN 50292 and from the alarm manufacturers instructionsCommissioning CommissioningRecord serial number in Appliance Commissioning Annual Service Fitting a NEW Door Glass Fitting and Removal of BaffleFitting and Removal of the Grate Fitting and Removal of Cast Iron FirebricksJoint Fitting a new door sealBlack face Glass rope Seal Do not over tighten the clamp as this could break the glassHetas Approved Chimney Sweeps Adjusting Door Catch & HingesTo adjust the door hinge plate assembly Do not undo the catch more than 3-4mmSpare Parts Outer Door 10TH Service Service RecordsPage Division of Stovax

YMMB specifications

Yeoman YMMB, short for Yeoman Yet Another Model Builder, is an advanced tool in the realm of web development, particularly known for its capabilities in scaffolding projects and automating repetitive tasks. It serves as a robust generator framework, streamlined to enhance developer productivity by allowing them to focus on coding rather than setting up boilerplate code. Yeoman YMMB is designed for building modern web applications and provides a seamless workflow that integrates various technologies and development practices.

One of the main features of Yeoman YMMB is its powerful scaffolding ability. Developers can easily create a new project structure with just a few commands, generating the essential files and directories needed to kickstart a web application. This feature not only saves time but also ensures that developers adhere to best practices and standards in web development. The intelligent generators available with Yeoman YMMB can create everything from single-page applications to entire web ecosystems.

Yeoman YMMB leverages several modern web technologies that have become industry standards. For instance, it supports popular front-end frameworks like React, Angular, and Vue.js, making it a versatile choice for developers working on diverse projects. Additionally, it comes with built-in support for various CSS preprocessors such as Sass and Less, enhancing the styling process and allowing for more maintainable stylesheets.

Another characteristic of Yeoman YMMB is its emphasis on modularity. The generator ecosystem enables developers to create and share custom generators that can be tailored to specific project requirements. This feature fosters a collaborative environment, as developers can build upon each other’s work, thereby speeding up the development process.

In terms of configuration, Yeoman YMMB offers a flexible setup, allowing developers to integrate with task runners like Gulp and Grunt. This integration enables automation of tasks such as minification, linting, and testing, streamlining the development workflow. With these automation tools, developers can focus more on writing code and less on managing the build process.

Moreover, Yeoman YMMB is community-driven, meaning it benefits from continuous updates and improvements based on user contributions. The active community provides extensive documentation and a plethora of plugins, each designed to enhance functionality and features. Through this collaboration, Yeoman YMMB remains relevant and up-to-date with the latest trends in web development.

In summary, Yeoman YMMB is an essential tool for web developers who seek efficiency and modernization in their workflow. Its scaffolding capabilities, support for modern technologies, modularity, and community-driven enhancements make it a valuable asset in building contemporary web applications.
Top Page Image Contents