Yeoman YMMB manual ASH Removal, Extended burning, Over-Firing, Chimney fire, Multi-fuel

Page 9

USER INSTRUCTIONS

7. ASH REMOVAL

Do not allow ash to build up in the appliance as it will not burn properly and may cause damage.

7.1Wood

—Open doors and using gloves remove ashpan with the tool provided (see Diagram 10).

—Remove ash and place into a Yeoman Ash Caddy (Yeoman Part No. 4227) or other suitable container.

Do not place hot ash in any container made from plastic or any other combustible material.

—De-ash at least once a week or when ashpan is full.

10

Ashpan

PR9033

7.2Multi-fuel:

—De-ash the appliance before filling with new fuel. Do not allow ash to build up on the underside of the grate as this can cause premature failure.

—Riddle (see Diagram 11).

11

Riddling

Handle

PR9035

—Remove ash and place into a Yeoman Ash Caddy (Yeoman Part No. 4227) or other suitable container.

Do not place hot ash in any container made from plastic or any other combustible material.

—De-ash at least once a week or when ashpan is full.

8.EXTENDED burning

8.1It is possible to get the appliance to burn for extended periods of time. In order to do this:

—De-ash prior to final refuelling.

—Set air controls to low combustion settings.

This will gradually blacken the glass but it will clear when operated at a high temperature for a short period.

—Use smokeless fuel or small, thick logs.

9.OVER-FIRING

9.1Do not over-fill with fuel or run at high temperatures for long periods or over-firing can occur. If the flue pipe, flue collar or top plate glow red the appliance is over-firing. Close the air controls to reduce the temperature.

9.2Over-firing can cause permanent damage to the appliance and invalidate the product warranty.

Warning: Do not operate the appliance with the Primary Air Control open for long periods of time as this could cause over- firing and may cause permanent damage.

10.Chimney fire

10.1If a chimney fire occurs:

—Shut all air controls immediately.

—Evacuate the building.

—Call the fire brigade.

—Do not re-enter the building until it is confirmed safe.

10.2Do not use the appliance after a chimney fire until:

a)It has been inspected by a registered installer* who has confirmed the appliance is safe to use.

b)The chimney system has been inspected and swept by a chimney sweep, confirming the system is structurally sound and free from obstruction**.

c)It is repaired as required before re-use. Use only genuine Yeoman replacement parts to keep your appliance in safe, efficient working order.

*Registered on the Competent Persons Scheme (GB only)/ INFO (Republic of Ireland only) see page 25 for details.

**This should be done by a HETAS Approved Chimney Sweep (UK only)/INFO registered (Republic of Ireland only) see page 26, who will issue you with a certificate.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Models Ymmb Yeoman CL Milner BrickInstallation Technical Specification Ymmb Appliance Commissioning Checklist User InstructionsPRE-INSTALLATION Installation InstructionsInstallation Engineer Appliance Commissioning ChecklistRetailer appliance was purchased from Essential Information Must be completedUser Instructions For Air Controls see DiagramGeneral Points Triple Air SystemsIf necessary seek expert advice Using the Appliance for the First TimeUse a protected gloved hand to operate Do not touch the paint during the first period of useRecommended Fuels Lighting The applianceWood Logs Do not close the Secondary Air control when burning wood Air Wash AdjustRunning The appliance Burning Solid fuelBurning tips Extended burning ASH RemovalOVER-FIRING Chimney fireCleaning Glass General CleaningChimney Sweeping Care of stoveTroubleshooting tips Seasonal useSmoke Control kit Standard features TECHNICAL SPECIFICATIONCL Milner Brick Packing listCL Inset Dimensions Site Requirements103 369 243 282 104 379 156 281 593 520 Max. Draught = 2.0mm Wg Min. Draught = 1.0mm Wg U.K Flue or ChimneyFlue Plate AdditionalFor advice before proceeding Minimum dimensions HearthFlue Outlet Positions Hearth and appliance. Consult a structural engineerFire surround clearances Milner Brick OpeningOpening 555-560mmFlue PRE-INSTALLATION ChecksVentilation ModelFitting Appliances on a boat Installing the Appliance Installation InstructionsLegal requirements Ø16mm rope Slide stove into positionRemoval of the LOG Guard Removal of the doorRemoval of the baffle Do not use appliance without the log guard in positionLift and rotate the centre grate see Diagram Centre grate Removal of the GrateDo not modify the baffle system Co alarms Removal of Cleanburn ChamberBS EN 50292 and from the alarm manufacturers instructions Removal of Cast Iron FIREbricksCommissioning CommissioningRecord serial number in Appliance Commissioning Annual Service Fitting and Removal of the Grate Fitting and Removal of BaffleFitting and Removal of Cast Iron Firebricks Fitting a NEW Door GlassBlack face Glass rope Seal Fitting a new door sealDo not over tighten the clamp as this could break the glass JointTo adjust the door hinge plate assembly Adjusting Door Catch & HingesDo not undo the catch more than 3-4mm Hetas Approved Chimney SweepsSpare Parts Outer Door 10TH Service Service RecordsPage Division of Stovax

YMMB specifications

Yeoman YMMB, short for Yeoman Yet Another Model Builder, is an advanced tool in the realm of web development, particularly known for its capabilities in scaffolding projects and automating repetitive tasks. It serves as a robust generator framework, streamlined to enhance developer productivity by allowing them to focus on coding rather than setting up boilerplate code. Yeoman YMMB is designed for building modern web applications and provides a seamless workflow that integrates various technologies and development practices.

One of the main features of Yeoman YMMB is its powerful scaffolding ability. Developers can easily create a new project structure with just a few commands, generating the essential files and directories needed to kickstart a web application. This feature not only saves time but also ensures that developers adhere to best practices and standards in web development. The intelligent generators available with Yeoman YMMB can create everything from single-page applications to entire web ecosystems.

Yeoman YMMB leverages several modern web technologies that have become industry standards. For instance, it supports popular front-end frameworks like React, Angular, and Vue.js, making it a versatile choice for developers working on diverse projects. Additionally, it comes with built-in support for various CSS preprocessors such as Sass and Less, enhancing the styling process and allowing for more maintainable stylesheets.

Another characteristic of Yeoman YMMB is its emphasis on modularity. The generator ecosystem enables developers to create and share custom generators that can be tailored to specific project requirements. This feature fosters a collaborative environment, as developers can build upon each other’s work, thereby speeding up the development process.

In terms of configuration, Yeoman YMMB offers a flexible setup, allowing developers to integrate with task runners like Gulp and Grunt. This integration enables automation of tasks such as minification, linting, and testing, streamlining the development workflow. With these automation tools, developers can focus more on writing code and less on managing the build process.

Moreover, Yeoman YMMB is community-driven, meaning it benefits from continuous updates and improvements based on user contributions. The active community provides extensive documentation and a plethora of plugins, each designed to enhance functionality and features. Through this collaboration, Yeoman YMMB remains relevant and up-to-date with the latest trends in web development.

In summary, Yeoman YMMB is an essential tool for web developers who seek efficiency and modernization in their workflow. Its scaffolding capabilities, support for modern technologies, modularity, and community-driven enhancements make it a valuable asset in building contemporary web applications.
Top Page Image Contents