Wayne Cast Iron Utility Series, 321304-001 Operation, Maintenance, Extension Cord Length Table

Page 2

Operating Instructions and Parts Manual

Installation (Continued)

 

EXTENSION CORD LENGTH TABLE

 

 

 

 

 

tor and grounding type attachment

Wire Size

#18

#16

#14

#12

Length

25 ft

50 ft

100 ft

150 ft

plug. A grounded receptacle in confor-

mance with current NEC and local codes

 

 

 

 

 

must be used (See Figure 1).

 

 

 

 

 

 

Grounding

Blade

Figure 1

2.This pump operates on 115V, 60 Hz AC, single phase or 115V DC.

3.Use an extension cord only if neces- sary. Follow the Extension Cord Length Table for proper gage of 3- wire, grounding type extension cord.

Risk of fatal electrical shock. Never cut off the round grounding prong. Cutting the cord or plug

will void the warranty and make the pump inoperable.

4.Figure 2 shows a typical installation. Threaded adapters are furnished for attaching garden hose where condi- tions permit its use. In no case should the pump be more than 15 feet above or away from inlet source. Install a foot valve and when suction lift is over 10 feet or when suction line is over 10 feet.

5.The inlet line may be galvanized pipe, plastic pipe, or reinforced hose. Small leaks in suction line

greatly reduce efficiency of pump and may prevent priming.

Ordinary garden hose will collapse

under suction pressure and should not be used in the inlet but for pressure boosting only.

6.Use a strainer when pumping from a creek, pond, or source where for- eign objects may be sucked into the pump. The strainer should prevent solids from entering the inlet line.

7.A regular garden hose may be used as a discharge line.

Operation

Pump must be filled with water

before operation. Running the pump dry will cause damage to the shaft seal.

1.This unit is not waterproof or weath- erproof and is not intended to be used in showers, saunas, or other potentially wet locations. The motor is designed to be used in a clean, dry location with access to adequate cooling air. Ambient temperatures around the motor should not exceed 104˚F (40˚C).

2.Remove priming plug and fill with water. Close plug

3.Plug power cord into GFCI protected electrical outlet. The pump will prime in a few minutes depending on suc- tion line length. Use of foot valve on suction line is recommended.

4.In the case of pressure boosting, turn water on before starting pump. This force primes the pump. Then, plug power cord into GFCI protect- ed electrical outlet.

5.Unplug cord to turn unit off.

Maintenance

Let pump cool for at least 20 minutes

before attempting to service. Motor may be extremely hot. Personal injury may result.

1.Pump should be checked periodically for proper operation.

Always disconnect the electrical supply

before attempting to install, service, or perform any maintenance. If the power source is out of sight, lock and tag in the open (off) position to prevent unex- pected power application. Failure to do so could result in fatal electrical shock. Only qualified electricians should repair this unit. Improper repair could result in fatal electrical shock.

BRUSH REPLACEMENT

Brushes for this pump should be

inspected after 100 hours of operation.

Pumps with excess of 100 hours of oper- ation may stop operating or fail to start. This could be due to worn brushes or carbon build-up. The brushes should be removed and carbon removed. Worn brushes are not covered under warran- ty. Replacement brushes may be avail- able from Wayne Pumps. Call 1-800-237- 0987 to order.

Priming Plug

Inlet

Hose Adapters

Outlet

1)Disconnect electrical cord from power supply.

2)Remove brush caps with screwdriver.

3)Remove old brush assembly.

4)Insert new brush assembly.

5)Replace brush caps.

For other problems, consult trou- bleshooting chart.

Figure 2

www.waynepumps.com

2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents General Safety Information Safety GuidelinesSpecifications InstallationBrush Replacement MaintenanceWire Size #18 #16 #14 #12 Length 25 ft 50 ft 100 ft 150 ft OperationTroubleshooting Chart Additional RepairsFor Replacement Parts, call Description Part Number QuantitySpécifications Directives de SécuritéGénéralités sur la Sécurité Série En Fonte Tout UsageEntretien Installation SuiteRemplacement DES Balais FonctionnementTeel Instructions d’Utilisation et Manuel de Pièces Entretien SuiteGuide de Dépannage Réparations AdditionnellesPour pièces de rechange, composer No. de Numéro Réf Description De Pièce QtéInformaciones Generales de Seguridad DescripciónMedidas de Seguridad InstalaciónTabla DE LAS Longitudes DE LOS Cordones DE Extensión FuncionamientoMantenimiento Tamaño del alambre #18 #16 #14 #12Guía de Diagnóstico de Averías Reparaciones AdicionalesPara ordenar repuestos en EUA Llame al Teléfono No. de Número Descripción Del repuesto Ctd

321304-001, Cast Iron Utility Series specifications

Wayne Cast Iron Utility Series, model 321304-001, is a highly reliable and robust pump designed to meet the demanding needs of residential and commercial applications. This utility pump excels in managing water transfer, dewatering, and draining tasks, making it an indispensable tool for homeowners, contractors, and facilities managers.

One of the standout features of the Wayne 321304-001 is its durable cast iron construction. This material not only enhances the longevity of the pump but also provides superior resistance to rust and corrosion, making it ideal for use in various environments. The heavy-duty design ensures that the pump can withstand wear and tear, particularly in challenging conditions, ensuring uninterrupted service.

The pump is equipped with a powerful motor, delivering a high flow rate, which means it can move a significant volume of water quickly and efficiently. This efficiency is particularly beneficial in situations where time is of the essence, such as during flooding or when draining a pool. The motor is thermally protected, preventing overheating and ensuring prolonged operation without the risk of damage.

The Wayne Cast Iron Utility Series also includes easy-to-understand operational features. The integrated float switch automates the activation and deactivation of the pump based on water levels, reducing the need for manual intervention. This feature ensures that the pump operates only when necessary, conserving energy and enhancing its overall efficiency.

In addition to its functional design, the pump is user-friendly, allowing for straightforward installation and maintenance. Its compact size facilitates portability, making it easy to transport between job sites or store when not in use. This versatility adds to the pump's appeal for both residential and commercial uses.

Another noteworthy characteristic of the Wayne 321304-001 is its capability to handle solids. With a robust design, it can handle small debris, making it suitable for various applications without the risk of clogging.

In summary, the Wayne Cast Iron Utility Series model 321304-001 combines durability, high performance, and user-centric features, making it a top choice for anyone looking for a dependable utility pump. Its cast iron construction, powerful motor, automated float switch, and user-friendly design cement its status as a reliable solution for all water management needs. Whether for flood recovery, draining tasks, or general water transfer, this utility pump stands out as an essential tool for homeowners and professionals alike.
Top Page Image Contents