Kidde KN-COPD-3-UK manual Quick Set Up Guide

Page 4

2520-7203-00.qxd 2006.4.7 3:50 PM Page 2

Quick Set Up Guide

We urge you to read this entire manual in the sequence it is presented.

Listed below are five easy steps for setting up your Kidde CO Alarm. Please read this entire guide for complete information.

Note: This CO alarm must be installed by a competent person.

Step 1 - Determine the best location for your CO alarm(s). Refer to Installation, Where to Install Your Alarm for complete information.

Step 2 - Install the 9 volt backup battery. To install the battery, open the back cover and snap the battery connector onto the battery. You will hear the alarm sound briefly to indicate the unit is receiving power. At power up, you will see a flashing red dot and three eights in the digital display indicating the alarm is warm- ing up. After approximately 20 seconds the unit will start sampling for CO. During this period a number will appear on the digital display. The number on the digital display should be zero (0). See “Normal Operating Characteristics” for complete information on operating characteristics.

Place the battery into the battery compartment and replace the back cover.

IMPORTANT!

A small screwdriver or similar tool may be required to remove the back cover. The back cover should be levered up from the centre recess at the bottom of the alarm. The cover is designed this way to discourage the removal of batteries, or tampering, by young children.

Step 3 - Determine how you want to mount the alarm. Your CO alarm is equipped to be mounted as a corded, a direct plug, or a table top unit. Refer to Installation, How to Install your Alarm for complete instructions about how to configure your alarm for installation.

Step 4 - Install the alarm. Plug the alarm into a standard un-switched 230 volt AC electrical outlet in one of the alarm configurations listed in step 3. Wait 2 to 3 minutes after power up and make sure the red dot in the digital display is blinking.

Step 5 - Test the unit’s operation by pressing and releasing the Test/Reset button. Within 15 seconds you will hear 8 seconds of quick beeps.

While testing the alarm, have someone else check that the alarm can be heard easily from the sleeping areas. The unit should be located where it can wake you if it alarms at night.

Your alarm is now monitoring for the presence of CO.

For complete testing information, refer to How to Test Your CO Alarm” section.

Caution: Continuous exposure to the loud 85 decibel alarm at close range over an extended period of time may cause hearing loss. We recommend that you cover the front of the unit while testing the alarm with the palm of your hand.

2

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Carbon Monoxide Alarm Table of Contents Qxd 2006.4.7 350 PM Quick Set Up Guide Introduction Carbon MonoxideFeatures Where to Install Your CO Alarm What Carbon Monoxide Can and Cannot DoMounting Configuration InstallationWhere Not to Install Your CO Alarm How to Install Your CO Alarm Direct Plug Alarm Wall Mounted AlarmTable Top Alarm Normal Operating CharacteristicsHow to Test Your CO Alarm Low Battery WarningNormal Operation How to Know If Your Alarm is Malfunctioning If the alarm malfunctionsMalfunction Signal Group 1 Component Failure Malfunction Signal Group 2 Microprocessor FailureHow to Care for Your Alarm To Reset the Peak Level Memory… Peak Level Memory ButtonEffects of CO Exposure Your Family at Risk for CO PoisoningHome Safety Tips What You Can Do Where CO Comes FromWhat You Can do to Protect Your Family What You Should Know Before the Alarm Sounds Indicators of Possible CO LeaksHidden Causes of CO Emission What You Should Not DoEffects of Carbon Monoxide Exposure Effects of Carbon Monoxide ExposureWhat To Do When The Alarm Sounds What to Do When the Alarm Sounds for Carbon MonoxideWhat To Do When The Alarm Sounds W Adjacent to the residenceHaemoglobin test. This test measures the amount of CO Immediately after CO exposure. Acute CO poisoning is usuCall a Qualified Technician to Find and Repair the Problem Sometimes it’s Difficult to Find the Source of CO in a HomeProduct Specifications Battery BackupTest/Reset Button Technical InformationReplacement of the Alarm How the Unit Determines When to AlarmAccuracy of the Digital Display Display Readings AlarmSound Action Plug into AC asWarranty For Warranty Service Questions or for More Information

KN-COPD-3-UK specifications

The Kidde KN-COPD-3-UK is an advanced carbon monoxide detector that provides crucial protection against the dangers of CO gas, a silent and deadly threat often produced by faulty appliances or insufficient ventilation. Designed for residential use, the device integrates cutting-edge technologies and user-focused features to ensure the safety and peace of mind of families across the UK.

One of the standout features of the KN-COPD-3-UK is its electrochemical sensor, which is highly reliable and sensitive to even the smallest concentrations of carbon monoxide. This technology enables the detector to activate swiftly, providing early warnings and potentially saving lives. With a detection range of 0-300 parts per million, the device is capable of identifying dangerous CO levels that may emerge from everyday appliances such as gas boilers, fireplaces, and stoves.

The device boasts a compact and stylish design, allowing it to blend seamlessly into any home environment. With its easy-to-read digital display, users can monitor CO levels in real-time, giving them immediate awareness of potential hazards. The display also features a backlit option, making it convenient to read in low-light conditions, ensuring that it remains user-friendly around the clock.

Another key characteristic of the Kidde KN-COPD-3-UK is its audible alarm, which is set to emit a series of loud beeps when it detects elevated levels of carbon monoxide. This alarm is complemented by visual alerts that flash when CO is present, ensuring that occupants are promptly informed of the situation. The device is also equipped with a test/reset button, allowing users to check its functionality easily.

For ease of installation, the Kidde KN-COPD-3-UK is designed to be wall-mounted or placed on a shelf, providing flexibility depending on user preferences. Importantly, the device features a battery backup, ensuring continuous operation even in the event of a power outage, enhancing overall reliability.

With a lifespan of up to 10 years, this carbon monoxide detector is an investment in safety that requires minimal maintenance. Its energy-efficient design adds to its appeal, ensuring that it operates effectively without excessive power consumption.

Overall, the Kidde KN-COPD-3-UK offers a robust combination of advanced sensor technology, user-friendly features, and reliable performance, making it an essential addition to any household looking to safeguard against the hazards of carbon monoxide.
Top Page Image Contents