Kidde KN-COPD-3-UK manual Installation, Mounting Configuration, Where Not to Install Your CO Alarm

Page 8

2520-7203-00.qxd 2006.4.7 3:50 PM Page 6

Installation

Mounting Configuration

LOCATION

Your Kidde CO Alarm should be mounted in or near bedrooms and liv- ing areas or wherever you suspect a CO exposure to be likely. It is rec- ommended that you install a Kidde CO Alarm on each level of a multi- level home.

CAUTION: This alarm will only indicate the presence of CO at the sen- sor. Carbon monoxide may be present in other areas.

IMPORTANT: Improper location can affect the sensitive electronic com- ponents in this alarm. Please see the next section describing where NOT to install this alarm.

Where Not to Install Your CO Alarm

To avoid causing damage to the unit, to provide optimum protection, and to prevent unnecessary alarms, follow the directions below where NOT to install this alarm:

It is not recommended that you install this CO Alarm in garages or kitchens. Installation in these areas could lead to nuisance alarms, may expose the sensor to substances that could damage or contaminate it, or the alarm may not be heard by persons in other areas of the home, especially if they are sleeping.

In the garage, vehicle exhaust can contain some CO. These levels are higher when the engine is first started. Within hours of starting a vehicle and backing it out of the garage, the level of remaining CO present can activate the alarm and cause a nuisance alarm.

In the kitchen, some gas appliances can emit a short burst of CO upon start-up. This is normal. If your CO Alarm is mounted too close to these appliances, it may alarm often and become a nuisance.

If you must install a Kidde CO Alarm near a cooking or heating appli- ance, install AT LEAST 1.5 metres (5 feet) away from the appliance.

Do not install the alarm in excessively dusty, dirty or greasy areas such as kitchens, garages and boiler rooms. Dust grease or household chemicals can contaminate or coat the alarm’s sensors, causing the alarm not to operate properly.

Do not obstruct the vents on the alarm. Place the alarm where drapes, furniture or other objects do not block the flow of air to the vents.

Do not install in dead air spaces, such as peaks of vaulted ceilings, a gabled roof or within 15.2 cm (6”) of ceiling, where CO may not reach the sensor in time to provide early warning.

Do not install in turbulent air from ceiling fans. Do not install near doors and windows that open to the outside, near fresh air vents, or anywhere that is drafty. Rapid air circulation from fans or fresh air from outside may cause the sensors to display an inaccurate reading.

6

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Carbon Monoxide Alarm Table of Contents Qxd 2006.4.7 350 PM Quick Set Up Guide Introduction Carbon MonoxideFeatures Where to Install Your CO Alarm What Carbon Monoxide Can and Cannot DoWhere Not to Install Your CO Alarm InstallationMounting Configuration How to Install Your CO Alarm Direct Plug Alarm Wall Mounted AlarmTable Top Alarm Normal Operating CharacteristicsNormal Operation Low Battery WarningHow to Test Your CO Alarm How to Know If Your Alarm is Malfunctioning If the alarm malfunctionsMalfunction Signal Group 1 Component Failure Malfunction Signal Group 2 Microprocessor FailureHow to Care for Your Alarm To Reset the Peak Level Memory… Peak Level Memory ButtonEffects of CO Exposure Your Family at Risk for CO PoisoningWhat You Can do to Protect Your Family Where CO Comes FromHome Safety Tips What You Can Do What You Should Know Before the Alarm Sounds Indicators of Possible CO LeaksHidden Causes of CO Emission What You Should Not DoEffects of Carbon Monoxide Exposure Effects of Carbon Monoxide ExposureWhat To Do When The Alarm Sounds What to Do When the Alarm Sounds for Carbon MonoxideWhat To Do When The Alarm Sounds W Adjacent to the residenceHaemoglobin test. This test measures the amount of CO Immediately after CO exposure. Acute CO poisoning is usuCall a Qualified Technician to Find and Repair the Problem Sometimes it’s Difficult to Find the Source of CO in a HomeProduct Specifications Battery BackupTest/Reset Button Technical InformationAccuracy of the Digital Display How the Unit Determines When to AlarmReplacement of the Alarm Sound AlarmDisplay Readings Action Plug into AC asWarranty For Warranty Service Questions or for More Information

KN-COPD-3-UK specifications

The Kidde KN-COPD-3-UK is an advanced carbon monoxide detector that provides crucial protection against the dangers of CO gas, a silent and deadly threat often produced by faulty appliances or insufficient ventilation. Designed for residential use, the device integrates cutting-edge technologies and user-focused features to ensure the safety and peace of mind of families across the UK.

One of the standout features of the KN-COPD-3-UK is its electrochemical sensor, which is highly reliable and sensitive to even the smallest concentrations of carbon monoxide. This technology enables the detector to activate swiftly, providing early warnings and potentially saving lives. With a detection range of 0-300 parts per million, the device is capable of identifying dangerous CO levels that may emerge from everyday appliances such as gas boilers, fireplaces, and stoves.

The device boasts a compact and stylish design, allowing it to blend seamlessly into any home environment. With its easy-to-read digital display, users can monitor CO levels in real-time, giving them immediate awareness of potential hazards. The display also features a backlit option, making it convenient to read in low-light conditions, ensuring that it remains user-friendly around the clock.

Another key characteristic of the Kidde KN-COPD-3-UK is its audible alarm, which is set to emit a series of loud beeps when it detects elevated levels of carbon monoxide. This alarm is complemented by visual alerts that flash when CO is present, ensuring that occupants are promptly informed of the situation. The device is also equipped with a test/reset button, allowing users to check its functionality easily.

For ease of installation, the Kidde KN-COPD-3-UK is designed to be wall-mounted or placed on a shelf, providing flexibility depending on user preferences. Importantly, the device features a battery backup, ensuring continuous operation even in the event of a power outage, enhancing overall reliability.

With a lifespan of up to 10 years, this carbon monoxide detector is an investment in safety that requires minimal maintenance. Its energy-efficient design adds to its appeal, ensuring that it operates effectively without excessive power consumption.

Overall, the Kidde KN-COPD-3-UK offers a robust combination of advanced sensor technology, user-friendly features, and reliable performance, making it an essential addition to any household looking to safeguard against the hazards of carbon monoxide.
Top Page Image Contents