Beckett CF1000 manual Follow These Instructions Exactly, Protect Against Stray Light Lockout

Page 5

Owner’s Responsibility:

Follow These Instructions

Exactly

Failure to follow these instructions, misuse, or incorrect adjustment of the burner could lead to equipment malfunction and result in asphyxia- tion, explosion or fire.

Contact a professional, qualified service agency for the installation, adjustment and service of your oil burning system. Thereafter, have your equipment adjusted and inspected at least annually to ensure reliable operation. This work requires technical training, trade experience, licensing or certification in some states and the proper use of special combustion test instruments.

Please carefully read and comply with the following instructions:

yNever store or use gasoline or other flammable liquids or vapors near this burner or appliance.

yNever attempt to burn garbage or refuse in this appli- ance.

yNever attempt to light the burner by throwing burning material into the appliance.

yNever attempt to burn any fuel not specified and ap- proved for use in this burner.

yNever restrict the air inlet openings to the burner or the combustion air ventilation openings in the room.

Professional Installer/Service Agency Responsibility:

Follow These

Instructions Exactly

Failure to follow these instructions could lead to equipment malfunc- tion and result in asphyxiation, explosion or fire.

yPlease read all instructions before proceeding. Follow all instructions completely.

yThis equipment must be installed, adjusted and started by a qualified service agency that is experienced with all applicable codes and ordinances and responsible for the installation and commission of the equipment.

yThe installation must comply with all local codes and ordinances having jurisdiction and the latest editions of the NFPA 31 and CSA-B139 & B140 in Canada.

NOTICE

50 Hz motors — The burner ratings, air settings and nozzle ratings are based on standard 60 hz motors (at 3450 rpm). Derate all ratings 20% when using 50 hz motors. Consult factory for specific application data.

NOTICE

High altitude installations — Accepted industry practice requires no derate of burner capacity up to 2,000 feet above sea level. For altitudes higher than 2,000 feet, derate burner capacity 2% for each 1000 feet above sea level.

Pre-installation check- list

Protect Against Stray

Light Lockout

Failure to follow these instructions could cause loss of burner operation resulting in no heat, an unplanned process interruption, work stoppage and the potential for frozen plumbing or other cold weather property damage.

yThe control must detect a dark, no-flame condition in order to start the burner or it will hold in the stray light lockout mode.

yShield the burner view window from direct exposure to intense light.

Protect Against Dust and

Moisture

Wet, dusty environments could lead to blocked air passages, corrosion damage to components, impaired combustion performance and result in asphyxiation, explosion or fire.

yThis burner is designed for clean, dry installations.

yElectrical controls are not protected against rain or sprayed water.

yKeep the installation clear of dust, dirt, corrosive va- pors, and moisture.

yProtective covers and more frequent maintenance may be required.

Adequate Combustion

and Ventilation Air Supply

Required

Failure to provide adequate air supply could se- riously affect the burner performance and result in damage to the equipment, asphyxiation, ex- plosion or fire hazards.

yThe burner cannot properly burn the fuel if it is not sup- plied with a reliable combustion air source.

yFollow the guidelines in the latest editions of the NFPA 31 and CSA-B139 regarding providing adequate air for combustion and ventilation.

Form 6104 BCF10-R06

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents To the Homeowner or Equipment Owner To the Professional, Qualified Installer or Service AgencyPotential for Fire, Smoke and Asphyxiation Hazards Form 6104 BCF10-R06 Table of Contents Indicates an imminently Hazardous situation Specifications Agency approvalsProtect Against Stray Light Lockout Follow These Instructions ExactlyProtect Against Dust Moisture Adequate Combustion Ventilation Air Supply RequiredCorrect Nozzle and Flow Rate Required Oil Supply Pressure Con- trol Required‰ Electrical supply ‰ Vent system‰ Verify burner components ‰ Verify firing rateProtect the Air Tube From Overheating ‰ Install nozzle‰ Mount flanges on air tube ‰ Mount air tube to burner‰ Set dimension Z ‰ Install nozzle line assembly‰ Insert burner Do Not Install By-pass Plug with 1-Pipe System‰ Fuel unit by-pass plug ‰ Oil supply/return lines‰ Burner fuel flow Install Oil Supply To SpecificationsProfessional Installation Service Required Do Not Bypass Safety ControlsKeep Service Access Cov- ers Securely Installed Electrical Shock HazardSequence of Operation typical ‰ Z dimension‰ Initial head position Figure ‰ Adjusting plate assembly Figure‰ Initial air settings Figure Hot Gas Puff-back Heavy Smoke Hazard Explosion and Fire Hazard‰ Set appliance limit controls ‰ Prepare the fuel unit for air venting‰ Set air adjusting plate Figure Annual service by qualified service techni- cian Annual Professional Service RequiredMonthly maintenance by owner Replacement parts Form 6104 BCF10-R06 Warranty

CF1000 specifications

The Beckett CF1000 is a cutting-edge, reliable, and efficient commercial burner designed for use in various heating applications. Known for its exceptional performance, it is increasingly popular among businesses and contractors looking for an effective solution to meet their heating needs.

One of the main features of the CF1000 is its advanced combustion technology. The burner is engineered to deliver optimal combustion efficiency, reducing emissions and enhancing fuel economy. This technology not only helps in lowering operational costs but also aligns with modern environmental regulations, making the CF1000 a responsible choice for energy-conscious businesses.

Another notable characteristic of the CF1000 is its ability to handle multiple fuel types, including oil and natural gas. This versatility allows users to choose the best fuel source for their specific application, contributing to operational flexibility. Additionally, the CF1000 is equipped with a modulation system that adjusts the burner output in response to demand, ensuring consistent heating without unnecessary energy consumption.

The CF1000 also stands out for its compact design, making it easy to install in various settings, whether in commercial buildings or industrial facilities. Its robust construction is designed to withstand demanding conditions, ensuring longevity and reliability. Moreover, the burner comes with advanced safety features, including flame monitoring and integrated shut-off systems, helping to prevent potential hazards during operation.

Ease of maintenance is another significant advantage of the Beckett CF1000. The design incorporates user-friendly service access points, allowing technicians to perform routine maintenance and inspections quickly and efficiently. This not only ensures optimal performance but also extends the lifespan of the burner.

Furthermore, the CF1000 is supported by Beckett's extensive customer service and technical support. Their commitment to quality and satisfaction means that users can rely on expert assistance whenever needed, ensuring peace of mind.

Overall, the Beckett CF1000 is a premier choice for those seeking a high-performance commercial burner. With its advanced combustion technology, versatile fuel options, compact design, and a wealth of safety features, it delivers reliable heating solutions suitable for a wide range of applications. Its ease of maintenance combined with robust support services makes the CF1000 an intelligent investment for any business prioritizing efficiency, safety, and reliability in their heating systems.
Top Page Image Contents