Beckett CF1000 manual ‰ Set air adjusting plate Figure

Page 16
IF burner stops after flame established —
‰
5. If the burner motor does not start, reset the motor overload switch (if so equipped) and press the reset switch of the burner primary control.
6. Vent the fuel unit as soon as the burner motor starts rotating. To vent —
‰ Attach a clear plastic tube to the air bleed valve (Figure 8 or 9 as applies, item p).
‰ Place the end of the tube in a container to catch the oil. Then loosen the fuel unit air vent valve.
‰ Tighten the air vent valve after all air has been purged. ‰ IF burner stops during venting —
yThe burner primary control will lockout if flame is not established within its time limit. This is typically 15 seconds for R7184B primary controls, but may be less for other flame supervisory controls.
yThe burner may lockout several times during the period needed to purge all the air. Press the red reset button for ½ second during the prepurge cycle to extend air venting time.

yAdditional venting is probably required. Repeat the air venting procedure.

7.Once flame is steady, proceed to Set air adjusing plate.

‰Set air adjusting plate (Figure 12)

1.Allow the burner to run until the appliance has warmed sufficiently.

2.Visually check the flame. The flame should not be dark orange or smoky. If the flame appears to be smoking, increase the amount of air by re-adjusting the damper indicator to a higher number.

3.Once the appliance has warmed, the air setting can be checked and adjusted.

4.Use combustion test instruments to adjust the burner.

a.Adjust the air until a trace of smoke is achieved with CO2 level as high as possible (lowest possible O2).

Example: 13.5% CO2 (2.5% O2) with a trace of smoke.

b.Increase the air to reduce CO2 by 2 percentage points at a zero smoke level. (Increase O2 by 3 percentage points at a zero smoke level.)

Example: Reduce CO2 from 13.5% to 11.5%, with zero smoke (or increase O2 from 2.5% to 5.5%).

c.This procedure provides a margin of reserve air to ac- commodate variable conditions.

5.Check the breech draft pressure against the appliance manufacturer’s recommended setting (typically + 0.1” W.C.).

6.If the breech pressure is higher or lower than recommend- ed level, adjust the appliance breech damper to achieve

the specified setting. Recheck the smoke and CO2 levels. Adjust burner air if necessary and tighten the air adjust- ing plate screw securely.

16

Form 6104 BCF10-R06

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Potential for Fire, Smoke and Asphyxiation Hazards To the Professional, Qualified Installer or Service AgencyTo the Homeowner or Equipment Owner Form 6104 BCF10-R06 Table of Contents Agency approvals Indicates an imminently Hazardous situation SpecificationsFollow These Instructions Exactly Protect Against Stray Light LockoutProtect Against Dust Moisture Adequate Combustion Ventilation Air Supply RequiredOil Supply Pressure Con- trol Required Correct Nozzle and Flow Rate Required‰ Vent system ‰ Electrical supply‰ Verify burner components ‰ Verify firing rate‰ Install nozzle Protect the Air Tube From Overheating‰ Mount flanges on air tube ‰ Mount air tube to burner‰ Install nozzle line assembly ‰ Set dimension ZDo Not Install By-pass Plug with 1-Pipe System ‰ Insert burner‰ Fuel unit by-pass plug ‰ Oil supply/return linesInstall Oil Supply To Specifications ‰ Burner fuel flowDo Not Bypass Safety Controls Professional Installation Service RequiredKeep Service Access Cov- ers Securely Installed Electrical Shock Hazard‰ Z dimension Sequence of Operation typical‰ Initial air settings Figure ‰ Adjusting plate assembly Figure‰ Initial head position Figure Explosion and Fire Hazard Hot Gas Puff-back Heavy Smoke Hazard‰ Set appliance limit controls ‰ Prepare the fuel unit for air venting‰ Set air adjusting plate Figure Monthly maintenance by owner Annual Professional Service RequiredAnnual service by qualified service techni- cian Replacement parts Form 6104 BCF10-R06 Warranty

CF1000 specifications

The Beckett CF1000 is a cutting-edge, reliable, and efficient commercial burner designed for use in various heating applications. Known for its exceptional performance, it is increasingly popular among businesses and contractors looking for an effective solution to meet their heating needs.

One of the main features of the CF1000 is its advanced combustion technology. The burner is engineered to deliver optimal combustion efficiency, reducing emissions and enhancing fuel economy. This technology not only helps in lowering operational costs but also aligns with modern environmental regulations, making the CF1000 a responsible choice for energy-conscious businesses.

Another notable characteristic of the CF1000 is its ability to handle multiple fuel types, including oil and natural gas. This versatility allows users to choose the best fuel source for their specific application, contributing to operational flexibility. Additionally, the CF1000 is equipped with a modulation system that adjusts the burner output in response to demand, ensuring consistent heating without unnecessary energy consumption.

The CF1000 also stands out for its compact design, making it easy to install in various settings, whether in commercial buildings or industrial facilities. Its robust construction is designed to withstand demanding conditions, ensuring longevity and reliability. Moreover, the burner comes with advanced safety features, including flame monitoring and integrated shut-off systems, helping to prevent potential hazards during operation.

Ease of maintenance is another significant advantage of the Beckett CF1000. The design incorporates user-friendly service access points, allowing technicians to perform routine maintenance and inspections quickly and efficiently. This not only ensures optimal performance but also extends the lifespan of the burner.

Furthermore, the CF1000 is supported by Beckett's extensive customer service and technical support. Their commitment to quality and satisfaction means that users can rely on expert assistance whenever needed, ensuring peace of mind.

Overall, the Beckett CF1000 is a premier choice for those seeking a high-performance commercial burner. With its advanced combustion technology, versatile fuel options, compact design, and a wealth of safety features, it delivers reliable heating solutions suitable for a wide range of applications. Its ease of maintenance combined with robust support services makes the CF1000 an intelligent investment for any business prioritizing efficiency, safety, and reliability in their heating systems.
Top Page Image Contents