Burnham SM-6 manual Lubrication

Page 24

where conditions warrant) to flush out the sediment

discoloration. Probe type low water cutoff should be

chamber so the device will be free to function properly.

removed once a year, examined and cleaned of any

Low water fuel cutoffs and water feeders should be

dirt accumulations to assure proper operation. Do not

attempt to repair mechanisms in the field. Complete

dismantled annually by qualified personnel, to the

replacement mechanisms including necessary gaskets

extent necessary to insure freedom from obstructions

and installation instructions are available from the

and proper functioning of the working parts. Inspect

manufacturer.

connecting lines to boiler for accumulation of mud,

 

scale, etc. and clean as required. Examine all visible

9 LUBRICATION

wiring for brittle or worn insulation and make sure

There are no parts requiring lubrication on the part of

electrical contacts are clean and that they function

the serviceman or the homeowner. Circulator bearings

properly. Give special attention to solder joints on

are water lubricated. Fan motor bearings are factory

bellows and float when this type of control is used.

sealed.

Check float for evidence of collapse and check mercury

 

bulb (where applicable) for mercury separation or

 

Figure 16

CLEANING OF VENT SYSTEM, BOILER FLUES, AND BURNERS

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Spacemastertm Important Information Please Read this page Carefully Table of Contents General Installation Requirements Boiler Location Must Meet the Following Site RequirementsMinimum Clearance to Combustible Surfaces ½ 1.6 ft ¾ 2.1 ft II. Installation Instructions Vent System Cross Section Oxygen Corrosion Recommended Boiler Piping Page Electric Wiring Installation Inspect Installation Before Starting Initial Start III. Operating InstructionsFollow These Operating Instructions Schematic Wiring Diagram Ladder Wiring Diagram Sequence of Operation Trouble Shooting Check GAS Input Rate to BoilerPage Page Page Typical Pilot Flame Main Burner Flame IV. Service Burners and Firebox should be Cleaned AnnuallyRemoval of Burner Assembly Maintenance of LOW Water CutoffLubrication Avoid Breathing Fiber Particulates and Dust Repair Parts VI. Low Water Cut Off Lwco WhenLimited Warranty

SM-6 specifications

The Burnham SM-6 is a high-performance modular boiler designed for commercial and industrial applications. Known for its efficiency and reliability, the SM-6 is engineered to meet a wide range of heating demands while maintaining low operational costs.

One of the standout features of the SM-6 is its modular design. This allows for scalable installations, catering to varying heating needs without requiring extensive modifications. The boiler can operate independently or in conjunction with other units, providing flexibility that is essential for industries with fluctuating demands.

In terms of technology, the Burnham SM-6 utilizes advanced combustion technology to achieve high efficiency rates. The unit typically operates with a stellar thermal efficiency of around 85% to 90%, minimizing fuel consumption and reducing greenhouse gas emissions. The incorporation of electronic ignition further helps in conserving energy, as it eliminates the need for a standing pilot light.

The SM-6 is made from high-quality materials designed for durability and long service life. The heat exchanger is constructed with durable steel, enabling it to withstand high temperatures and pressures. This robust construction ensures reliability in demanding environments, mitigating the risk of breakdowns and enhancing overall productivity.

Another key characteristic of the Burnham SM-6 is its user-friendly control system. The boiler is equipped with a state-of-the-art control panel that provides operators with real-time data on performance metrics. This allows for proactive maintenance and performance optimization, enhancing the overall operational efficiency of the system.

Safety is also a paramount consideration in the design of the SM-6. It includes multiple safety features, such as pressure relief valves and electronic safety checks, to prevent dangerous operating conditions. These features ensure that the boiler can run safely over extended periods, providing peace of mind for facility managers.

In conclusion, the Burnham SM-6 boiler stands out in the market for its modular design, high efficiency, durable construction, and advanced control technologies. Its versatile nature makes it an excellent choice for various applications, from manufacturing facilities to commercial buildings, ensuring it meets the heating requirements of diverse industries effectively. The combination of efficiency, reliability, and safety solidifies the Burnham SM-6 as a leading solution in the realm of heating systems.
Top Page Image Contents