Ariston 47-116-13, 41-116-01 Installation, Reference Standards, Siting the Appliance

Page 6

2.

INSTALLATION

The technical information and instructions provided herein below are intended

 

 

for the installer so that the unit may be installed correctly and safely.

 

 

The installation and initial startup of the boiler must be by a CORGI Approved

2.1

Reference Standards

Installer in compliance with the installation standards currently in effect, as well

as with any and all local health and safety standards i.e. CORGI.

 

 

This appliance must be installed by a competent installer in

 

 

accordance with the current Gas Safety (installation & use)

 

 

Regulations

 

 

 

 

 

The installation of this appliance must be in accordance with the relevant

 

 

requirements of the current Gas Safety (installation & use) Regulations, the

 

 

Local Building Regulations, the current I.E.E. Wiring Regulations, the byelaws

 

 

of the local water authority, and in Scotland, in accordance with the Building

 

 

Standards (Scotland) Regulation and Health and Safety document No. 635

 

 

“Electricity at work regs. 1989”.

 

 

 

 

 

Installation should also comply with the following British Standard Codes of

 

 

Practice:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Low pressure

 

 

 

 

 

 

pipes

BS 6891

1988

 

 

 

 

 

 

 

 

 

 

 

Boilers of rated input

 

 

 

 

 

 

not exceeding 60 kW

BS 6798

1987

 

 

 

 

Forced circulation hot

 

 

 

 

 

 

water system

BS 5449

1990

 

 

 

 

 

 

 

 

 

 

 

Installation of gas hot water

 

 

 

 

 

 

supplies for domestic purposes

 

 

 

 

 

( 2nd family gases)

BS 5546

1990

 

 

 

 

Flues

BS 5440-1

1990

 

 

 

 

 

 

 

 

 

 

 

Air supply

BS 5440-2

1989

 

 

 

 

 

 

 

 

2.2Siting the Appliance

The appliance may be installed in any room or indoor area, although particular attention is drawn to the requirements of the current I.E.E. Wiring Regulations, and in Scotland, the electrical provisions of the Building Regulations applicable in Scotland, with respect to the installation of the combined appliance in a room containing a bath or shower.

Where a room-sealed appliance is installed in a room containing a bath or shower the boiler and any electrical switch or appliance control, utilising mains electricity should be situated so that it cannot be touched by a person using the bath or shower.

The location must permit adequate space for servicing and air circulation around the appliance as indicated in paragraph 2.4.

The location must permit the provision of an adequate flue and termination. For unusual locations special procedures may be necessary.

BS 6798-1987 gives detailed guidance on this aspect.

A compartment used to enclose the appliance must be designed specifically for this purpose. No specific ventilation requirements are needed for an installation within a cupboard

This appliance is not suitable for outdoor installation.

The type C appliances (in which the combustion circuit, air vent intake and combustion chamber are air-tight with respect to the room in which the appliance is installed) can be installed in any type of room.

There are no limitations with respect to ventilation and the volume of the room itself. The boiler must be installed on a solid, permanent wall to prevent access to the electrical parts (when live) through the aperture on the back frame.

6

B004

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Leave These Instructions Adjacent to the GAS Meter Table of Contents General Information General InformationTechnical Information Genus 27 Rffi System Overall ViewInstallation Reference StandardsSiting the Appliance Overall Dimensions ClearancesMounting the Appliance Electrical ConnectionGas Connection Pipe Work Safety Valve DischargeWater Connections View of the Boiler Connections By-passMains Water Feed Central Heating Flue ConnectionsAir Release Points FillingTower Flue Components 80 mm B004 KW 27 kW Exhaust/Air Maximum Extension Room Thermostat Connection Electrical Diagram ColoursGenus 27 Rffi System CN202 Water Circuit Diagram Removing the Casing CommissioningInitial Preparation Filling the Heating SystemControl Panel Summer/Winter/Flue Analysis ModesInitial Start-up Operational Adjustments Checks to be run before initial start-up are as followsCombustion Analysis Fume Discharge MonitoringBoiler Safety Systems GAS Adjustments Changing the Type of GasMaintenance Wiring Diagram for Two Heating Zones MiscellaneousWiring Diagram for Connection to Ariston Unvented Cylinder TypicalB004 B004 B004 Technical Service Hotline 01494

47-116-08. 47-116-09, 41-116-01, 47-116-13 specifications

Ariston has cemented its reputation as a pioneer in the realm of heating and hot water solutions, consistently delivering quality products that marry efficiency with performance. Among their impressive lineup, models like the Ariston 47-116-13, 41-116-01, 47-116-08, and 47-116-09 stand out due to their innovative technologies and user-centric designs.

One of the defining features of these Ariston models is their advanced heating technology, which efficiently delivers hot water while minimizing energy consumption. They utilize a robust insulation system that prevents heat loss, ensuring that water stays hot for longer periods. This not only enhances convenience but also contributes to lower energy bills.

The 47-116-13 model showcases Ariston's commitment to smart engineering with its built-in digital display. This feature allows users to monitor and adjust temperatures effortlessly, ensuring customized comfort. Additionally, the model is equipped with a sleek design, making it a stylish addition to any home setting.

The 41-116-01 model emphasizes user-friendliness through its intuitive controls and compact design, making it suitable for various installations, from small apartments to larger homes. Its lightweight construction facilitates easier handling and installation, further enhancing its appeal.

In contrast, the 47-116-08 model is designed with durability in mind, featuring a corrosion-resistant tank that promises longevity. This model also incorporates advanced heating elements that ensure rapid heating, allowing users to enjoy hot water whenever they need it.

Finally, the 47-116-09 resonates with environmentally conscious consumers, as it is designed to be energy-efficient while providing reliable performance. This model utilizes a smart control system that adapts to user habits, ensuring optimal energy usage without sacrificing comfort.

In summary, Ariston's 47-116-13, 41-116-01, 47-116-08, and 47-116-09 models exemplify the brand's dedication to creating high-performance, energy-efficient heating solutions. With features such as advanced heating technology, user-friendly controls, and durable materials, these models are ideal for anyone looking to enhance their hot water experience while enjoying significant cost savings and reduced environmental impact.
Top Page Image Contents