Kenmore 153.33097 Service and Adjustment, Tank Sediment Cleaning, Vent System Inspection

Page 20

SERVICE AND ADJUSTMENT

Tank (Sediment) Cleaning

Sediment build-up on the tank bottom may create varying amount of noise and if left in the tank will cause permanent tank failure. In some water areas, you may not be able to drain all sediment deposits by simply draining the tank. In these cases Mag-Erad (part no. 23600) can be used to help remove the sediment deposits. This may be ordered from the Sears Service Center. For ordering, refer to the Parts Order List section.

Vent System Inspection

At least once a year a visual inspection should be made of the venting system. You should look for:

•Obstructions which could cause improper venting. The combustion and ventilation air flow must not be obstructed.

•Damage or deterioration which could cause improper venting or leakage of combustion products.

•Rusted flakes around top of water heater.

Be sure the vent piping is properly connected to prevent escape of dangerous flue gasses which could cause deadly asphyxiation.

Obstructions and deteriorated vent systems may present serious health risk or asphyxiation.

Chemical vapor corrosion of the flue and vent system may occur if air for combustion contains certain chemical vapors. Spray can propellants, cleaning solvents, refrigerator and air conditioner refrigerants, swimming pool chemicals, calcium and sodium chloride, waxes, bleach and process chemicals are typical compounds which are potentially corrosive.

If when inspecting the vent system you find sooting or deterioration, something is wrong. Call the local gas supplier to correct the problem and clean or replace the flue and venting before resuming operation of the water heater.

Burner Inspection

Flood damage to a water heater may not be readily visible or immediately detectable. However, over a period of time a flooded water heater will create dangerous conditions which can cause

DEATH, SERIOUS BODILY INJURY, OR PROPERTY DAMAGE. Contact a Sears Service Center to replace a flooded water heater. Do not attempt to repair the unit! It must be replaced!

At least once a year a visual inspection should be made of the main burner. See Figure 23.

CORRECT FLAME

SOFT BLUE

FIGURE 23.

Inspect burner flames through viewport. Flames should be very small with a blue haze and small amounts of yellow or orange at the edges. After several minutes of operation the burner screen may glow red. If large flames are observed at anytime shut-off unit and contact a Sears Service Center.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents GAS Water Heater Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.ASafe INSTALLATION, USE and Service Sears, Roebuck and CoSafety Precautions Table of Contents Product Specifications Customer ResponsibilitiesAdditional Tools Needed When Sweat Soldering Materials and Basic Tools NeededMaterials Needed Basic ToolsTypical Installation Pilot & Main BurnerInstallation Instructions Installation is Completed, seeRemoving the Old Water Heater Turn OFF the gas supply to the water heaterFacts to Consider About the Location Insulation Blankets ALL AIR from Inside Buildings See on page 10 and belowWater Piping Hotter Water can ScaldValve and Pipe Insulation Temperature-Pressure Relief Valve Local gas supplier for further information Filling the Water HeaterVenting Gas Piping GAS Piping with Flexible Connector Sediment TrapsOperating Instructions Temperature Regulation SettingsService and Adjustment Tank Sediment CleaningVent System Inspection Burner InspectionUltra Low NOx Natural Gas Burner Removing the Burner Door AssemblyReplacing the Pilot Assembly External Inspection & Cleaning of the Flame Arrestor Cleaning the Pilot AssemblyCleaning the Combustion Chamber and Flame Arrestor Replacing the ThermocouplePiezoelectric Igniter System Replacing the Burner Door AssemblyTesting the Igniter System Anode Rod Inspection Removing and Replacing the Gas Control Valve/ThermostatHousekeeping Temperature-Pressure Relief Valve Operation Drain Valve Washer ReplacementService DrainingTroubleshooting Guide Start Up ConditionsOperational Conditions CondensationRecovery Burner will not IgniteSmelly Water Pilot will not LightDrip from Relief Valve Thermostat Fails toShut OFF Combustion OdorsPilot Light Troubleshooting Chart Section a Pilot light will not lightParts Order List 153.330960 Gallon 153.330970MY-HOME

153.33097, 153.33096 specifications

Kenmore has long been a trusted name in home appliances, and their washer models 153.33096 and 153.33097 are no exception. These machines stand out for their modern features, advanced technology, and user-friendly characteristics that cater to the needs of today’s households.

One of the main features of both models is their efficient cleaning performance. The machines are equipped with a powerful wash system that ensures thorough dirt and stain removal, even from heavily soiled fabrics. The dual-action agitator in each model enhances the washing process by allowing optimal movement of laundry, resulting in cleaner clothes in less time.

In terms of capacity, the Kenmore 153.33096 and 153.33097 offer a generous wash drum size, accommodating large loads. This is particularly convenient for families or individuals who do laundry less frequently. The higher capacity not only saves time between cycles but also reduces water and energy consumption, making these washers environmentally friendly options.

The models feature various wash cycles and temperature settings to suit different fabric types and soiling levels. Users can select from options like delicate, heavy-duty, and quick wash cycles, providing flexibility for various laundry needs. This versatility is further enhanced by the inclusion of a digital display and intuitive controls, making it easy to customize each wash.

Another key characteristic of the 153.33096 and 153.33097 is the incorporation of advanced technology. The machines utilize a smart sensor system that detects load sizes and automatically adjusts water levels accordingly. This feature not only conserves water but also ensures optimal cleaning performance for every load.

Noise reduction technology is also a significant advantage of these Kenmore models. Using advanced sound-dampening materials, they operate quietly, making them a desirable choice for any household, especially in open-plan living spaces.

In summary, the Kenmore 153.33096 and 153.33097 washers are exemplary products that combine performance, efficiency, and user-friendly design. With their robust features, advanced technologies, and thoughtful characteristics, they deliver an exceptional laundry experience that meets the demands of modern life. Whether you're dealing with everyday laundry or specialized items, these Kenmore models offer tailored solutions to ensure outstanding cleanliness and convenience.
Top Page Image Contents