Jenn-Air W10323791 installation instructions Electronic Ignition System

Page 11

Electronic Ignition System

Install Burner Heads and Caps

Install the burner head, making sure the alignment pins are properly aligned with the burner base. Place burner cap (black) on top of the burner head.

20,000 Btu/h Ultra Power™ Dual-Flame

Burner

A

A. Incorrect

B. Correct

B

15,000 Btu/h Professional Burner

A

A. Incorrect

B. Correct

B

5,000 Btu/h Simmer/Melt Burner

A

A. Incorrect

B. Correct

B

Flame Height

The cooktop flame should be a steady blue flame approximately ¼" (0.64 cm) high.

Dual Flame Burner

A

B

A. Upper flame

B. Lower (simmer) flame

Single Flame Burner

To Adjust Flame Height:

1.Unplug range or disconnect power.

2.Remove burner grates.

3.Remove the control knobs.

4.Open the oven door and remove the 2 screws on each side of the range that hold the control console in place.

Initial Lighting and Gas Flame Adjustments

Cooktop burners use electronic igniters in place of standing pilots. When the cooktop control knob is turned to any position, the system creates a spark to light the burner. This sparking continues, until the flame is lit or the knob is turned to Off.

Check Operation of Cooktop Burners

Push in and turn each control knob to the “LITE” position.

The surface burners and grill flames should light within

4 seconds. The first time a burner is lit it may take longer than 4 seconds to light because of air in the gas line.

After verifying the proper burner operation, turn the control knobs to OFF.

If burners do not light properly:

■Turn cooktop control knob to the “OFF” position.

■Check that the range is plugged in and the circuit breaker has not tripped or the fuse has not blown.

■Check that the gas shutoff valves are set to the “open” position.

■Check that burner caps are properly positioned on burner bases.

Repeat start-up. If a burner does not light at this point, contact your dealer or authorized service company for assistance.

NOTE: Make sure to leave oven door open or the control console will not rest in the side brackets properly once it is detached.

5.Pull up on the control console and let it drop forward into the notched console brackets on each side.

A

A. Control console bracket

6.Remove the round gasket from the valve stem.

7.Put a control knob onto the valve stem of the burner you want to adjust.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Installation Instructions Your safety and the safety of others are very important Range SafetyTools and Parts Installation RequirementsLocation Requirements Mobile Home Additional Installation RequirementsProduct Dimensions 30 76.2 cm models Mobile home installations require½ 3.8 cm J 7.6 cm K 12.7 cm Cabinet Dimensions48 121.9 cm models 18 45.7 cm upper cabinet to countertopNatural Gas Electrical RequirementsGas Supply Requirements Type of GasBurner Input Rating Altitude Gas Supply Pressure TestingGas Supply Line Gas Pressure RegulatorMeasurement B Installation InstructionsInstall Anti-Tip Bracket Unpack RangeWall Mounting Pipe thread Adapter Flexible connectorMake Gas Connection Floor MountingComplete Connection Install GriddleVerify Anti-Tip Bracket Location Level RangeElectronic Ignition System Check Operation of Oven Bake Burners Reinstall Kick PlateComplete Installation If you need Assistance or ServiceTo range Shutoff valve closed position Gas supply line GAS ConversionsLP Gas Conversion To Convert Gas Pressure RegulatorOven bake burner screws Oven bake burner electrode bracket Gas Supply Pressure TestingBake burner cover Oven baffle Oven baffle nutsGas orifice spud Oven bake burner electrode bracket Electrode bracket clipGrasp electrode here Bracket Broil burner screw Broil burner orifice hole Replace Oven Bake Burner CoverCover notches Shoulder screws Oven back Broil burner orifice Broil burner orifice hole AB CPull electrode out of bracket Burner orifice spud To Convert Surface BurnersComplete Installation Natural Gas Conversion Lift up and remove oven bake burner cover and set aside Pull electrode out of bracket Replace Oven Bake Burner Cover AB C Pull electrode out of bracket Size stamp Burner cap Burner headAtlas 15-pin Wiring DiagramsUser Interface UI HMI Keyboard 48 121.9 cm Oven Schematic for JGRP548 ModelStrip Circuits Burner Cooktop SchematicSW4 SW5 SW6 Votre sécurité et celle des autres est très importante Sécurité DE LA CuisinièreOutils et pièces Exigences DinstallationDimensions du produit Modèles de 30 76,2 cm Exigences d’emplacement½ 3,8 cm J 7,6 cm K 12,7 cm Modèles de 36 91,4 cm Dimensions du placardModèles de 48 121,9 cm 15 38,1 cmType de gaz Spécifications électriquesSpécifications de lalimentation en gaz Test de pressurisation de la canalisation de gaz Canalisation de gazDétendeur Débit thermique des brûleurs AltitudeMesure B Instructions D’INSTALLATIONInstallation de la bride antibasculement Déballage de la cuisinièreVis n 12 x 1⁵⁄₈ Bride antibasculement Raccordement au gazMontage au plancher Montage au murAchever le raccordement Vérification de lemplacement de la bride AntibasculementInstallation de la plaque à frire Réglage de laplomb de la cuisinièreSystème dallumage électronique En affleurement avec le dessus de la cuisinière Réinstallation du garde-piedsConversion pour lalimentation au propane Achever l’installationConversions Pour Changement DE GAZ Détendeur Conversion du détendeurTest de pressurisation de la canalisation de gaz Couvercle du brûleur de cuisson au four Gicleur Saisir lélectrode ici SupportBrûleur de cuisson au four couvercle Réinstaller le couvercle du brûleur de cuisson au fourEncoches de couvercle Vis à épaulement AB C Dégager lélectrode du support Chapeau de brûleur Conversion des brûleurs de surfaceGicleur de brûleur Chapeau de brûleur Ouverture de gaz Base du brûleurAchever l’installation Conversion pour lalimentation au gaz naturel Déflecteur du four Écrous du déflecteur du four Lame plate puis retirer lélectrode Réinstaller le couvercle du brûleur de cuisson au four AB C Dégager lélectrode du support Réinstaller le couvercle du brûleur de cuisson au four Marquage pour identification de la taille Chapeau de brûleur Tête de brûleurRemarques Schémas de câblageInterface Utilisateur IU Schéma du four de 48 121,9 cm pour modèle JGRP548Schéma de la table de cuisson à 4 brûleurs Schémas des circuitsSchéma de la table de cuisson à 6 brûleurs 2010 10/10 All rights reserved

W10323791 specifications

The Jenn-Air W10323791 is a premium appliance part designed for select models of Jenn-Air refrigerators, particularly optimized for maintaining efficient cooling and temperature management. As a replacement part, the W10323791 offers exceptional reliability, aligning with the brand's reputation for high-quality kitchen appliances.

One of the main features of the W10323791 is its ability to regulate temperature effectively within the refrigerator. It plays a crucial role in ensuring that food items remain fresh for longer periods by maintaining consistent cooling. This component acts as a thermostat, enabling precise temperature control, which is vital for preserving the quality of perishable goods. With the W10323791, households can rest assured that their refrigeration system is operating at optimal performance, thanks to its durable construction and advanced capabilities.

Another notable characteristic of the W10323791 is its compatibility with various Jenn-Air refrigerator models. This versatility makes it easier for users to find a replacement that fits their specific appliance, ensuring a seamless integration into existing systems. The part is designed for straightforward installation, allowing homeowners to replace it without requiring professional help, thus saving both time and money.

In terms of technology, the W10323791 incorporates advanced materials that enhance its longevity and resistance to wear and tear. The component undergoes rigorous testing to meet the high standards set by Jenn-Air, making it a trusted choice for consumers seeking dependable appliance parts. Moreover, its energy-efficient design contributes to lower utility bills, aligning with today's emphasis on sustainability and cost-effective living.

In summary, the Jenn-Air W10323791 is a key component that underscores the brand's commitment to quality and innovation. With its focus on temperature control, compatibility, and durability, the W10323791 ensures that your Jenn-Air refrigerator operates efficiently, delivering fresh food and preserving culinary delights. Whether you are replacing a worn-out part or enhancing your kitchen's functionality, the W10323791 stands out as an essential part of a modern kitchen. It embodies the integration of advanced technology with user-friendly design, making it an excellent choice for any Jenn-Air refrigerator owner.
Top Page Image Contents