Jenn-Air W10323791 Electrical Requirements, Gas Supply Requirements, Type of Gas, Natural Gas

Page 6

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

IMPORTANT: The range must be electrically grounded in accordance with local codes and ordinances, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this range be provided.

■Electronic ignition systems operate within wide voltage limits, but proper grounding and polarity are necessary. Check that the outlet provides 120-volt power and is correctly grounded.

■The wiring diagram is located behind the kick plate in a clear plastic bag.

Gas Supply Requirements

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes and ordinances. In the absence of local codes, installation must conform with American National Standard, National Fuel Gas Code ANSI Z223.1/NFPA 54 - latest edition or CAN/CGA B149 - latest edition.

IMPORTANT: Range must be connected to a regulated gas supply.

IMPORTANT: Leak testing of the range must be conducted according to the manufacturer’s instructions.

Type of Gas

Natural Gas:

This range is design-certified by CSA International for use with Natural gas or, after proper conversion, for use with LP gas.

■This range is factory set for use with Natural gas. The model/ serial rating plate located under the console on the right-hand side has information on the types of gas that can be used. If the types of gas listed do not include the type of gas available, check with the local gas supplier.

LP Gas conversion:

Conversion must be done by a qualified service technician.

No attempt shall be made to convert the range from the gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. To convert to LP gas, use the LP gas conversion kit provided with your range and see the “Gas Conversions” section. The parts for this kit are in the literature package supplied with the range.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Installation Instructions Range Safety Your safety and the safety of others are very importantInstallation Requirements Tools and PartsMobile home installations require Mobile Home Additional Installation RequirementsProduct Dimensions 30 76.2 cm models Location Requirements18 45.7 cm upper cabinet to countertop Cabinet Dimensions48 121.9 cm models ½ 3.8 cm J 7.6 cm K 12.7 cmType of Gas Electrical RequirementsGas Supply Requirements Natural GasGas Pressure Regulator Gas Supply Pressure TestingGas Supply Line Burner Input Rating AltitudeUnpack Range Installation InstructionsInstall Anti-Tip Bracket Measurement BFloor Mounting Pipe thread Adapter Flexible connectorMake Gas Connection Wall MountingLevel Range Install GriddleVerify Anti-Tip Bracket Location Complete ConnectionElectronic Ignition System If you need Assistance or Service Reinstall Kick PlateComplete Installation Check Operation of Oven Bake BurnersTo Convert Gas Pressure Regulator GAS ConversionsLP Gas Conversion To range Shutoff valve closed position Gas supply lineOven baffle Oven baffle nuts Gas Supply Pressure TestingBake burner cover Oven bake burner screws Oven bake burner electrode bracketOven bake burner electrode bracket Electrode bracket clip Grasp electrode here BracketGas orifice spud Replace Oven Bake Burner Cover Cover notches Shoulder screwsBroil burner screw Broil burner orifice hole AB C Oven back Broil burner orifice Broil burner orifice holePull electrode out of bracket To Convert Surface Burners Burner orifice spudComplete Installation Natural Gas Conversion Lift up and remove oven bake burner cover and set aside Pull electrode out of bracket Replace Oven Bake Burner Cover AB C Pull electrode out of bracket Burner cap Burner head Size stampWiring Diagrams Atlas 15-pin48 121.9 cm Oven Schematic for JGRP548 Model User Interface UI HMI KeyboardBurner Cooktop Schematic Strip CircuitsSW4 SW5 SW6 Sécurité DE LA Cuisinière Votre sécurité et celle des autres est très importanteExigences Dinstallation Outils et piècesExigences d’emplacement Dimensions du produit Modèles de 30 76,2 cm15 38,1 cm Modèles de 36 91,4 cm Dimensions du placardModèles de 48 121,9 cm ½ 3,8 cm J 7,6 cm K 12,7 cmSpécifications électriques Spécifications de lalimentation en gazType de gaz Débit thermique des brûleurs Altitude Canalisation de gazDétendeur Test de pressurisation de la canalisation de gazDéballage de la cuisinière Instructions D’INSTALLATIONInstallation de la bride antibasculement Mesure BMontage au mur Raccordement au gazMontage au plancher Vis n 12 x 1⁵⁄₈ Bride antibasculementRéglage de laplomb de la cuisinière Vérification de lemplacement de la bride AntibasculementInstallation de la plaque à frire Achever le raccordementSystème dallumage électronique Réinstallation du garde-pieds En affleurement avec le dessus de la cuisinièreAchever l’installation Conversions Pour Changement DE GAZConversion pour lalimentation au propane Conversion du détendeur Test de pressurisation de la canalisation de gazDétendeur Couvercle du brûleur de cuisson au four Saisir lélectrode ici Support GicleurRéinstaller le couvercle du brûleur de cuisson au four Encoches de couvercle Vis à épaulementBrûleur de cuisson au four couvercle AB C Dégager lélectrode du support Chapeau de brûleur Ouverture de gaz Base du brûleur Conversion des brûleurs de surfaceGicleur de brûleur Chapeau de brûleurAchever l’installation Conversion pour lalimentation au gaz naturel Déflecteur du four Écrous du déflecteur du four Lame plate puis retirer lélectrode Réinstaller le couvercle du brûleur de cuisson au four AB C Dégager lélectrode du support Réinstaller le couvercle du brûleur de cuisson au four Chapeau de brûleur Tête de brûleur Marquage pour identification de la tailleSchémas de câblage RemarquesSchéma du four de 48 121,9 cm pour modèle JGRP548 Interface Utilisateur IUSchémas des circuits Schéma de la table de cuisson à 4 brûleursSchéma de la table de cuisson à 6 brûleurs 2010 10/10 All rights reserved

W10323791 specifications

The Jenn-Air W10323791 is a premium appliance part designed for select models of Jenn-Air refrigerators, particularly optimized for maintaining efficient cooling and temperature management. As a replacement part, the W10323791 offers exceptional reliability, aligning with the brand's reputation for high-quality kitchen appliances.

One of the main features of the W10323791 is its ability to regulate temperature effectively within the refrigerator. It plays a crucial role in ensuring that food items remain fresh for longer periods by maintaining consistent cooling. This component acts as a thermostat, enabling precise temperature control, which is vital for preserving the quality of perishable goods. With the W10323791, households can rest assured that their refrigeration system is operating at optimal performance, thanks to its durable construction and advanced capabilities.

Another notable characteristic of the W10323791 is its compatibility with various Jenn-Air refrigerator models. This versatility makes it easier for users to find a replacement that fits their specific appliance, ensuring a seamless integration into existing systems. The part is designed for straightforward installation, allowing homeowners to replace it without requiring professional help, thus saving both time and money.

In terms of technology, the W10323791 incorporates advanced materials that enhance its longevity and resistance to wear and tear. The component undergoes rigorous testing to meet the high standards set by Jenn-Air, making it a trusted choice for consumers seeking dependable appliance parts. Moreover, its energy-efficient design contributes to lower utility bills, aligning with today's emphasis on sustainability and cost-effective living.

In summary, the Jenn-Air W10323791 is a key component that underscores the brand's commitment to quality and innovation. With its focus on temperature control, compatibility, and durability, the W10323791 ensures that your Jenn-Air refrigerator operates efficiently, delivering fresh food and preserving culinary delights. Whether you are replacing a worn-out part or enhancing your kitchen's functionality, the W10323791 stands out as an essential part of a modern kitchen. It embodies the integration of advanced technology with user-friendly design, making it an excellent choice for any Jenn-Air refrigerator owner.
Top Page Image Contents