Jenn-Air W10323791 installation instructions Replace Oven Bake Burner Cover

Page 24

13.Replace oven bake burner electrode inside bracket.

B

A

A. Oven bake burner electrode

B. Oven bake burner electrode bracket

14.Reinstall the oven bake burner and oven bake burner screws. See Step 6 for illustration.

15.Replace oven baffle and oven baffle nuts.

Replace Oven Bake Burner Cover

1.Align notches on the oven bake burner cover with shoulder screws in the bottom of the oven.

A

ABB

A. Cover notches (4)

B. Shoulder screws (4)

2.Lower cover and slide to left or right to slide shoulder screws into the narrow ends of the notches and lock in place.

A

A. Bake burner cover

To Convert Oven Broil Burner (30" [76.2 cm] and 36" [91.4 cm] models and the Right Oven Cavity on 48" [121.9 cm] models)

1.Remove broil burner screw and set aside.

A

B

C

A. Broil burner screw

B. Broil burner

C. Broil burner orifice hole

2.Pull the broil burner toward you until it slides out of the hole in the oven back, and pull the electrode out of the bracket. The broil burner will hang down in the back of the oven while you change the orifice.

A

B

A. Grasp electrode here.

B. Bracket

24

Image 24 Contents
Installation Instructions Range Safety Your safety and the safety of others are very importantInstallation Requirements Tools and PartsMobile Home Additional Installation Requirements Product Dimensions 30 76.2 cm modelsMobile home installations require Location RequirementsCabinet Dimensions 48 121.9 cm models18 45.7 cm upper cabinet to countertop ½ 3.8 cm J 7.6 cm K 12.7 cmElectrical Requirements Gas Supply RequirementsType of Gas Natural GasGas Supply Pressure Testing Gas Supply LineGas Pressure Regulator Burner Input Rating AltitudeInstallation Instructions Install Anti-Tip BracketUnpack Range Measurement BPipe thread Adapter Flexible connector Make Gas ConnectionFloor Mounting Wall MountingInstall Griddle Verify Anti-Tip Bracket LocationLevel Range Complete ConnectionElectronic Ignition System Reinstall Kick Plate Complete InstallationIf you need Assistance or Service Check Operation of Oven Bake BurnersGAS Conversions LP Gas ConversionTo Convert Gas Pressure Regulator To range Shutoff valve closed position Gas supply lineGas Supply Pressure Testing Bake burner coverOven baffle Oven baffle nuts Oven bake burner screws Oven bake burner electrode bracketOven bake burner electrode bracket Electrode bracket clip Grasp electrode here BracketGas orifice spud Replace Oven Bake Burner Cover Cover notches Shoulder screwsBroil burner screw Broil burner orifice hole AB C Oven back Broil burner orifice Broil burner orifice holePull electrode out of bracket To Convert Surface Burners Burner orifice spud Complete Installation Natural Gas Conversion Lift up and remove oven bake burner cover and set aside Pull electrode out of bracket Replace Oven Bake Burner Cover AB C Pull electrode out of bracket Burner cap Burner head Size stampWiring Diagrams Atlas 15-pin48 121.9 cm Oven Schematic for JGRP548 Model User Interface UI HMI KeyboardBurner Cooktop Schematic Strip CircuitsSW4 SW5 SW6 Sécurité DE LA Cuisinière Votre sécurité et celle des autres est très importanteExigences Dinstallation Outils et piècesExigences d’emplacement Dimensions du produit Modèles de 30 76,2 cmModèles de 36 91,4 cm Dimensions du placard Modèles de 48 121,9 cm15 38,1 cm ½ 3,8 cm J 7,6 cm K 12,7 cmSpécifications électriques Spécifications de lalimentation en gazType de gaz Canalisation de gaz DétendeurDébit thermique des brûleurs Altitude Test de pressurisation de la canalisation de gazInstructions D’INSTALLATION Installation de la bride antibasculementDéballage de la cuisinière Mesure BRaccordement au gaz Montage au plancherMontage au mur Vis n 12 x 1⁵⁄₈ Bride antibasculementVérification de lemplacement de la bride Antibasculement Installation de la plaque à frireRéglage de laplomb de la cuisinière Achever le raccordementSystème dallumage électronique Réinstallation du garde-pieds En affleurement avec le dessus de la cuisinièreAchever l’installation Conversions Pour Changement DE GAZConversion pour lalimentation au propane Conversion du détendeur Test de pressurisation de la canalisation de gazDétendeur Couvercle du brûleur de cuisson au four Saisir lélectrode ici Support GicleurRéinstaller le couvercle du brûleur de cuisson au four Encoches de couvercle Vis à épaulementBrûleur de cuisson au four couvercle AB C Dégager lélectrode du support Conversion des brûleurs de surface Gicleur de brûleurChapeau de brûleur Ouverture de gaz Base du brûleur Chapeau de brûleurAchever l’installation Conversion pour lalimentation au gaz naturel Déflecteur du four Écrous du déflecteur du four Lame plate puis retirer lélectrode Réinstaller le couvercle du brûleur de cuisson au four AB C Dégager lélectrode du support Réinstaller le couvercle du brûleur de cuisson au four Chapeau de brûleur Tête de brûleur Marquage pour identification de la tailleSchémas de câblage RemarquesSchéma du four de 48 121,9 cm pour modèle JGRP548 Interface Utilisateur IUSchémas des circuits Schéma de la table de cuisson à 4 brûleursSchéma de la table de cuisson à 6 brûleurs 2010 10/10 All rights reserved