Jenn-Air W10323791 Location Requirements, Mobile Home Additional Installation Requirements

Page 4

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

■It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located under the console on the right-hand side.

■It is recommended that a 600 CFM or larger range hood be installed above the range.

■It is not recommended that a microwave hood combination be mounted above the range.

■Recessed installations must provide complete enclosure of the sides and rear of the range.

■To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

■All openings in the wall or floor where range is to be installed must be sealed.

■Do not seal the range to the side cabinets.

■Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

■The anti-tip bracket must be installed. To install the anti-tip bracket shipped with the range, see “Install Anti-Tip Bracket” section.

■Grounded electrical supply is required. See “Electrical Requirements” section.

■Proper gas supply connection must be available. See “Gas Supply Requirements” section.

■Contact a qualified floor covering installer to check that the floor covering can withstand at least 200°F (93°C). Use an insulated pad or ¼" (0.64 cm) plywood over carpet and under range if installing range over carpeting.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or with local codes.

In Canada, the installation of this range must conform with the current standards CAN/CSA-A240-latest edition, or with local codes.

Mobile home installations require:

■When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.

Product Dimensions

30" (76.2 cm) models

A

B

C

E

D

A. Island trim

B. 27¾" (70.5 cm) depth with control panel, see NOTE*

C. 35¾" (89.6 cm) cooktop height when setting on the wheels D. 30" (76.2 cm) width

E. Model/serial rating plate location

36" (91.4 cm) models

A

B

C

E

D

A. Island trim

B. 27¹⁄₈" (68.9 cm) depth with control panel, see NOTE*

C. 35¾" (90.2 cm) cooktop height when setting on the wheels D. 36" (91.4 cm) width

E. Model/serial rating plate location

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Installation Instructions Range Safety Your safety and the safety of others are very importantInstallation Requirements Tools and PartsMobile Home Additional Installation Requirements Product Dimensions 30 76.2 cm modelsMobile home installations require Location RequirementsCabinet Dimensions 48 121.9 cm models18 45.7 cm upper cabinet to countertop ½ 3.8 cm J 7.6 cm K 12.7 cmElectrical Requirements Gas Supply RequirementsType of Gas Natural GasGas Supply Pressure Testing Gas Supply LineGas Pressure Regulator Burner Input Rating AltitudeInstallation Instructions Install Anti-Tip BracketUnpack Range Measurement BPipe thread Adapter Flexible connector Make Gas ConnectionFloor Mounting Wall MountingInstall Griddle Verify Anti-Tip Bracket LocationLevel Range Complete ConnectionElectronic Ignition System Reinstall Kick Plate Complete InstallationIf you need Assistance or Service Check Operation of Oven Bake BurnersGAS Conversions LP Gas ConversionTo Convert Gas Pressure Regulator To range Shutoff valve closed position Gas supply lineGas Supply Pressure Testing Bake burner coverOven baffle Oven baffle nuts Oven bake burner screws Oven bake burner electrode bracketGrasp electrode here Bracket Oven bake burner electrode bracket Electrode bracket clipGas orifice spud Cover notches Shoulder screws Replace Oven Bake Burner CoverBroil burner screw Broil burner orifice hole AB C Oven back Broil burner orifice Broil burner orifice holePull electrode out of bracket To Convert Surface Burners Burner orifice spudComplete Installation Natural Gas Conversion Lift up and remove oven bake burner cover and set aside Pull electrode out of bracket Replace Oven Bake Burner Cover AB C Pull electrode out of bracket Burner cap Burner head Size stampWiring Diagrams Atlas 15-pin48 121.9 cm Oven Schematic for JGRP548 Model User Interface UI HMI KeyboardBurner Cooktop Schematic Strip CircuitsSW4 SW5 SW6 Sécurité DE LA Cuisinière Votre sécurité et celle des autres est très importanteExigences Dinstallation Outils et piècesExigences d’emplacement Dimensions du produit Modèles de 30 76,2 cmModèles de 36 91,4 cm Dimensions du placard Modèles de 48 121,9 cm15 38,1 cm ½ 3,8 cm J 7,6 cm K 12,7 cmSpécifications de lalimentation en gaz Spécifications électriquesType de gaz Canalisation de gaz DétendeurDébit thermique des brûleurs Altitude Test de pressurisation de la canalisation de gazInstructions D’INSTALLATION Installation de la bride antibasculementDéballage de la cuisinière Mesure BRaccordement au gaz Montage au plancherMontage au mur Vis n 12 x 1⁵⁄₈ Bride antibasculementVérification de lemplacement de la bride Antibasculement Installation de la plaque à frireRéglage de laplomb de la cuisinière Achever le raccordementSystème dallumage électronique Réinstallation du garde-pieds En affleurement avec le dessus de la cuisinièreConversions Pour Changement DE GAZ Achever l’installationConversion pour lalimentation au propane Test de pressurisation de la canalisation de gaz Conversion du détendeurDétendeur Couvercle du brûleur de cuisson au four Saisir lélectrode ici Support GicleurEncoches de couvercle Vis à épaulement Réinstaller le couvercle du brûleur de cuisson au fourBrûleur de cuisson au four couvercle AB C Dégager lélectrode du support Conversion des brûleurs de surface Gicleur de brûleurChapeau de brûleur Ouverture de gaz Base du brûleur Chapeau de brûleurAchever l’installation Conversion pour lalimentation au gaz naturel Déflecteur du four Écrous du déflecteur du four Lame plate puis retirer lélectrode Réinstaller le couvercle du brûleur de cuisson au four AB C Dégager lélectrode du support Réinstaller le couvercle du brûleur de cuisson au four Chapeau de brûleur Tête de brûleur Marquage pour identification de la tailleSchémas de câblage RemarquesSchéma du four de 48 121,9 cm pour modèle JGRP548 Interface Utilisateur IUSchémas des circuits Schéma de la table de cuisson à 4 brûleursSchéma de la table de cuisson à 6 brûleurs 2010 10/10 All rights reserved

W10323791 specifications

The Jenn-Air W10323791 is a premium appliance part designed for select models of Jenn-Air refrigerators, particularly optimized for maintaining efficient cooling and temperature management. As a replacement part, the W10323791 offers exceptional reliability, aligning with the brand's reputation for high-quality kitchen appliances.

One of the main features of the W10323791 is its ability to regulate temperature effectively within the refrigerator. It plays a crucial role in ensuring that food items remain fresh for longer periods by maintaining consistent cooling. This component acts as a thermostat, enabling precise temperature control, which is vital for preserving the quality of perishable goods. With the W10323791, households can rest assured that their refrigeration system is operating at optimal performance, thanks to its durable construction and advanced capabilities.

Another notable characteristic of the W10323791 is its compatibility with various Jenn-Air refrigerator models. This versatility makes it easier for users to find a replacement that fits their specific appliance, ensuring a seamless integration into existing systems. The part is designed for straightforward installation, allowing homeowners to replace it without requiring professional help, thus saving both time and money.

In terms of technology, the W10323791 incorporates advanced materials that enhance its longevity and resistance to wear and tear. The component undergoes rigorous testing to meet the high standards set by Jenn-Air, making it a trusted choice for consumers seeking dependable appliance parts. Moreover, its energy-efficient design contributes to lower utility bills, aligning with today's emphasis on sustainability and cost-effective living.

In summary, the Jenn-Air W10323791 is a key component that underscores the brand's commitment to quality and innovation. With its focus on temperature control, compatibility, and durability, the W10323791 ensures that your Jenn-Air refrigerator operates efficiently, delivering fresh food and preserving culinary delights. Whether you are replacing a worn-out part or enhancing your kitchen's functionality, the W10323791 stands out as an essential part of a modern kitchen. It embodies the integration of advanced technology with user-friendly design, making it an excellent choice for any Jenn-Air refrigerator owner.
Top Page Image Contents