Empire Comfort Systems VFSUR30-2, VFSUR24-2, VFSUR18-2 Important Safety Information

IMPORTANT SAFETY INFORMATION

•An unvented room heater having an input rating of more than 6,000 Btu per hour shall not be installed in a bathroom

•An unvented room heater having an input rating of more than 10,000 Btu per hour shall not be installed in a bedroom or bath- room.

•Never burn solid fuels in a fireplace where a gas log set is in- stalled.

•Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

•Do not place clothing or other flammable material on or near the appliance.

•Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing ignition.

•Young children should be carefully supervised when they are in the same room as the appliance.

•This unit complies with ANSI Z21.11.2 Unvented Heaters and it also complies with ANSI Z21.60 Decorative Vented Appliances for Solid Fuel Burning Fireplaces. State or local codes may only allow operation of this appliance in a vented configuration. Check your state or local codes.

•Correct installation of logs, proper location of the heater and annual cleaning are necessary to avoid potential problems with sooting. Sooting, resulting from improper installation or opera- tion, can settle on surfaces outside the fireplace.

•Avoid any drafts that could alter burner flame patterns. Do not allow fans to blow directly into the fireplace. Do not place a blower inside burn box area of firebox. Ceiling fans may create drafts that alter burner flame patterns. Sooting and improper burning will occur as a result of drafts.

•WARNING: Do not allow fans to blow directly into the fireplace. Avoid any drafts that alter burner flame patterns.

•WARNING: Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this heater.

•WARNING: Do not operate this appliance unless all components including logs, burners, and controls are in good working condition. Never operate this appliance if any log or twig is broken, or out of their intended position. Refer to the Log set placement instructions for correct log and twig positioning.

Replacement components are available through your local dealer as indicated in the How to Order Repair Parts section of the appliance manual.

•Periodic examination and cleaning of the venting system of the solid-fuel burning fireplace, including frequency of such examination and cleaning, by a qualified agency.

•The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1*/NFPA54 or International Fuel Gas Code.

*Available from the American National Standards Institute, Inc. 11 West 42nd St., New York, N.Y. 10018

•NOTE: Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative that the control compart- ment, burners and circulating air passageways of the appliance be kept clean.

•Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the appliance. Provide adequate combustion and ventilation air.

•The flow of combustion and ventilation air MUST NOT be obstructed.

•Provide adequate clearances around air openings into the combustion chamber and adequate accessibility clearance for servicing and proper operation. NEVER obstruct the front opening of the appliance.

•An unvented room heater intended for installation in a solid-fuel burning fireplace shall comply with the following instructions.

•Afireplace screen must be in place when the appliance is operating and, unless other provisions for combustion air are provided, the screen shall have an opening(s) for introduction of combustion air.

•Solid-fuels shall not be burned in a masonry or UL 127 factory- built fireplace in which an unvented room heater is installed.

•Any glass doors shall be fully opened when the appliance is in operation.

•Any outside air ducts and/or ash dumps in the fireplace shall be permanently closed at time of appliance installation.

•WARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property damage.

•WARNING: Before installing in a solid-fuel burning fireplace, the chimney flue and firebox must be cleaned of soot, creosote, ashes and loose paint by a qualified chimney cleaner.

WARNING	CARBON MONOXIDE POISONING MAY LEAD TO DEATH.
	Early signs of carbon monoxide poisoning resemble the flu, with
When used without adequate combustion and ventilation air, heater
may give off CARBON MONOXIDE, an odorless, poisonous gas.	headache, dizziness and/or nausea. If you have these signs, heater
	may not be working properly. Get fresh air at once! Have heater
Do not install heater until all necessary provisions are made for
	serviced.
combustion and ventilation air. Consult the written instructions	Some people – pregnant women, persons with heart or lung disease,
provided with the heater for information concerning combustion	anemia, those under the influence of alcohol, those at high altitudes
and ventilation air. In the absence of instructions, refer to the	– are more affected by carbon monoxide than others.
National Fuel Gas Code, ANSI Z223.1, Section 5.3, International	The pilot light safety system senses the depletion of oxygen at its
Fuel Gas Code or applicable local codes.	location. If this heater is installed in a structure having a high
This heater is equipped with a PILOT LIGHT SAFETY SYSTEM	vertical dimension, the possibility exists that the oxygen supply at
designed to turn off the heater if not enough fresh air is available.	the higher levels will be less than that at the heater. In this type of
	application, a fan to circulate the structure air will minimize this
DO NOT TAMPER WITH PILOT LIGHT SAFETY SYSTEM!
	effect. The use of this fan will also improve the comfort level in the
If heater shuts off, do not relight until you provide fresh air.	structure. When a fan is used to circulate air, it should be located
If heater keeps shutting off, have it serviced. Keep burner and control	so that the air flow is not directed at the burner.
compartment clean.

Page 4 25741-0-0309