Hearth and Home Technologies BCBV36I owner manual Lighting, Instructions Standing, Pilot

Page 10

10

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1 or, in Canada, current CAN/CGA-B149.

• •

I.

For normal use, If your fireplace

Lighting

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn knob. Never use tools. If the manual gas valve will not push in or turn by hand, don't try to repair it; call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

This appliance must be properly connected to a venting system in accordance with the manufacturer's installation instructions.

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner's information manual provided with the appliance. For assistance or additional information consult a

activate/deactivate must be deactivated

Instructions (Standing

Heatilator

LIGHTING INSTRUCTIONS

Stop! Read the safety information above on this label.

qualified installer, service agency or the gas supplier.

CAUTION: Hot while in operation. Do

your for

fi

• BCBV36 • 4008-033 • Rev F • 12/08

1.Turn wall switch to the "OFF" position or thermostat to the lowest setting.

2.Remove control access panel.

3.Turn manual gas valve to CLOSED. Wait five [5] minutes to clear out any gas. If you then smell gas, STOP! Follow "B" in the safety information above on this label. If you don't smell gas, go to next step.

4.Turn gas line to "OPEN".

5.Turn pilot knob clockwise to "OFF". (Knob may have to be depressed to pass "PILOT" position.)

6.Locate pilot assembly inside appliance.

7.Locate red ignitor button.

8.Turn pilot knob to "PILOT" and push in.

9.Continue to hold in pilot knob and push the red ignitor button 12-15 times until small blue pilot flame appears.

10.Continue to hold in pilot knob for approximately one minute. Pilot should remain lit. If pilot goes out, wait 5 minutes and repeat Steps 3-9.

11.Release and turn knob counterclockwise to "ON".

12.If appliance will not operate, follow the instructions "TO TURN OFF GAS TO APPLIANCE" and call your service technician or

gas supplier.

NOTE: To light main burner, turn wall switch to "ON". Do not light by hand.

3.CLOSED

4.OPEN

7

5

 

ON

 

OT

 

 

5

 

 

PIL

OFF

 

 

OFF

VENT

ON

 

8 11

ON

OFF

PILOT

OFF ON

PIL OT

not touch. Keep children, clothing, furniture, gasoline and other liquids having flammable vapors away.

WARNING RISK OF FIRE

This appliance is intended to burn a specified gas fuel only. Do not attempt to use with solid wood fuel or another type of fuel. Do not attempt to modify or use any other type of gas burner system.

WARNING: Disconnect the electric power before servicing. If for any reason the original wire supplied with the appliance must be replaced, it must be replaced with 105° C or its equivalent.

For use with natural gas or propane. A conversion kit as supplied by the manufacturer shall be used to convert this appliance to the alternative fuel.

* Also certified for installation in a bedroom or a

bed-sitting room.

service or

replace

Pilot)

an extended period of time, follow

with the wall switch or remote

 

TO TURN OFF GAS TO APPLIANCE

1.

Turn off wall switch or set thermostat to lowest setting.

3.

Turn manual gas valve to "CLOSED position. Do not force.

2.

Remove control access panel.

4.

Replace control access panel.

Due to high surface termperatures, keep children, clothing and furniture away.

 

Keep burner and control compartment clean. See installation and operating instructions accompanying the appliance.

29097D

 

* For U.S. only!

NATURAL GAS

the

control.

instructions below.

 

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Vent Gas Appliance Installation and OperationModels What to do if you smell gasCongratulations Homeowner Reference InformationInstaller Guide Table of ContentsUser Guide Warranty Warranty Listing and Code Approvals Operating Instructions Gas Fireplace SafetyYour Fireplace Decorative Doors and Fronts Remote Controls, Wall Controls and Wall SwitchesClear Space Outside Air optionalFor Your Safety Read Before Lighting Lighting Instructions IPIInstructions Standing LightingPilot Initial Break-in Procedure Frequently Asked QuestionsAfter Fireplace is Lit Glass Cleaning Maintenance and ServiceMaintenance Tasks-Homeowner Remote ControlControl Compartment and Firebox Top LogsFirebox Burner Ignition and OperationGetting Started Typical Appliance SystemTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Negative Pressure Select Appliance Location Framing dimensions are the same with or without outside airFraming and Clearances Construct the Appliance ChaseClearances Clearances to CombustiblesMantels Mantel and Wall ProjectionsMantel Legs or Wall Projections Termination Locations Vent Termination Minimum ClearancesVent Guidelines Vent Information and DiagramsVent System Configuration Wall and Ceiling Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Vertical Penetration FramingGas and Electrical Connections Install Outside Air Kit Damper AssemblyAppliance Preparation Secure and Level the ApplianceInstall Attic Insulation Shield Installing Vent PipeAssembly of Vent Sections Secure Vent SectionsGas Pressure Gas InformationFuel Conversion Gas ConnectionIntellifire Ignition System Wiring Wiring RequirementsStanding Pilot Ignition System Wiring Optional Accessories RequirementsElectrical Service and Repair GASJunction Box Installation Prepare Junction Box BracketFinishing Facing MaterialAppliance Setup Place the Vermiculite Log Removal/Replacement Place the RockwoolAir Shutter Setting HoodTroubleshooting Standing Pilot Ignition SystemShould be Placed in this Opening Symptom Possible Cause Corrective Action Intellifire Ignition SystemPilot lights but continues Shorted or loose connection Appliance Dimension Diagram Reference MaterialsService Parts List BCBV36Service Parts ListBCBV36I Service Parts List Description Commnets Part NumberOptional Components SMART-BATT-HTLThis page intentionally left blank Contact Information

BCBV36I, BCBV36 specifications

Hearth and Home Technologies is a leader in delivering innovative heating solutions, and their BCBV36 and BCBV36I models demonstrate this commitment to quality and performance. These versatile fireplaces are designed to provide warmth, ambiance, and a modern aesthetic that complements various home styles.

The BCBV36 and BCBV36I models are built with efficiency and functionality in mind. They feature a clean-burning, vented gas design that produces realistic flames while maximizing heat output. With an impressive heating capacity, these fireplaces can effectively warm large living spaces, making them an ideal choice for homeowners looking to enhance their comfort and ambiance during the colder months.

One of the standout characteristics of the BCBV36 and BCBV36I is their customizable appearance. These models come with several decorative options, allowing users to choose from various logs, stones, and glass media to create the perfect centerpiece for their living area. The sleek design of the fireplace ensures that it fits seamlessly into any room, while the large viewing area offers an unobstructed view of the flames.

In terms of technology, both models are equipped with advanced electronic ignition systems for ease of use and reliability. The user-friendly control panel allows homeowners to adjust the flame height and heat output conveniently, enhancing the overall user experience. Additionally, the fireplaces can be integrated with remote control options for added convenience.

Safety is a critical aspect of any heating solution, and the BCBV36 and BCBV36I incorporate several features to ensure peace of mind. The built-in safety shut-off system eliminates risks associated with overheating while the heat exchanger design maximizes warmth while minimizing exhaust emissions.

Maintenance is also simplified with these models. The easy-to-remove glass fronts make it straightforward for homeowners to clean and maintain the fireplace, ensuring it remains a stunning focal point in the home.

In summary, the Hearth and Home Technologies BCBV36 and BCBV36I offer an exceptional blend of style, efficiency, and safety. With modern designs, customizable options, and advanced technology, these fireplaces are a fantastic investment for anyone looking to enhance their home’s atmosphere and heating capabilities. These qualities make them a top choice in the realm of residential gas fireplaces.
Top Page Image Contents