Hearth and Home Technologies PIER-40, BAY-40 Design and Installation Considerations, Draft

Page 15

B. Design and Installation Considerations

NOTICE: Check building codes prior to installation.

Installation MUST comply with local, regional, state and national codes and regulations.

Consult insurance carrier, local building inspector, fire officials or authorities having jurisdiction over restrictions, installation inspection and permits.

Before installing, determine the following:

Where the fireplace is to be installed

The vent system configuration to be used

Gas supply piping

Electrical wiring

Framing and finishing details

Whether optional accessories—devices such as a fan, wall switch or remote control—are desired

NOTICE: Junction box should be installed during initial setup to avoid major reconstruction.

C. Draft

Draft is the pressure difference needed to vent fireplaces successfully. When a fireplace is drafting successfully, all combustion byproducts are exiting the home through the chimney.

Considerations for successful draft include:

Preventing negative pressure

Location of fireplace and chimney

NOTICE: Hearth & Home Technologies assumes no responsibility for the improper performance of the fireplace system caused by:

Inadequate draft due to environmental conditions

Downdrafts

Tight sealing construction of the structure

Mechanical exhausting devices

Improper location of the chimney

D. Negative Pressure

WARNING! Risk of Asphyxiation! Negative pressure can cause spillage of combustion fumes and soot. Fire must draft properly for safe operation.

Negative pressure results from the imbalance of air avail- able for the fireplace to operate properly. It can be stron- gest in lower levels of the house.

Causes include:

Exhaust fans (kitchen, bath, etc.)

Range hoods

Combustion air requirements for furnaces, water heaters and other combustion appliances

Clothes dryers

Location of return-air vents to furnace or air conditioning

Imbalances of the HVAC air handling system

Upper level air leaks such as:

-Recessed lighting

-Attic hatch

-Duct leaks

To minimize the effects of negative air pressure:

Install the outside air kit with the intake facing prevailing winds during the heating season

Ensure adequate outdoor air for all combustion appliances and exhaust equipment

Ensure furnace and air conditioning return vents are not located in the immediate vicinity of the fireplace

Avoid installing the fireplace near doors, walkways or small isolated spaces

Recessed lighting should be a “sealed can” design

Attic hatches weather stripped or sealed

Attic mounted duct work and air handler joints and seams taped or sealed

Basement installations should be avoided

NOTICE: Hearth & Home Technologies Inc. recommends the use of direct vent fireplaces in basements.

Heat & Glo • BAY-40, PIER-40 • 34977 • Rev W • 11/08

15

Image 15
Contents Hot screen/mesh and glass doors will cause burns Fire RiskListing Label Information/Location GrateNumber Model Table of Contents Installer GuideUser Guide CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited WarrantyHeat & Glo BAY-40, PIER-40 34977 Rev W 11/08 Combustible Materials Listing and Code ApprovalsAppliance Certification Non-Combustible MaterialsOperating Instructions Your FireplaceHot glass will cause burns Firescreen Seasoned WoodStarting a Fire GrateVented Gas Log Sets & Gas Log Lighters Glass DoorsOutside Air optional Optional ComponentsHardwood vs Softwood Wood FuelMaintainance and Service Chimney Inspection/CleaningDisposal of Ashes Frequency As desired Glass CleaningCheck Firebox Refractory Inspect GrateStart Fire Problems Possible Cause Solution Troubleshooting GuideTypical Fireplace System Getting StartedDesign and Installation Considerations DraftNegative Pressure Frequently open doors Central heat outlets or returns Locating Fireplace & ChimneyTools and Supplies Needed Fireplace System RequirementsInspect Fireplace and Components Select Fireplace Location Framing & ClearancesAir Space Clearances ClearancesFrame the Fireplace Sidewalls/SurroundsPlace Protective Metal Hearth Strips Installation of FireplaceThings to Consider Position the FireplaceFt min. from top of uppermost chimney section to air inlet AK17 Installation BAY-40 Install Outside Air KitChimney Assembly Height of Chimney Components Chimney RequirementsExample Using Offsets/ReturnsAssemble Chimney Sections Install Chimney Air KitInstalling the Ceiling Firestop Install Ceiling Firestops330 mm Install Attic Insulation ShieldComplete Installation Install FlashingCut out Hole in Roof Flat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsInstall Chase Top Install Fireplace & ChimneyST1175 Square Termination Cap Install Termination CapTCT1175 Terra Cotta Cap Shrouds Radiation ShieldField Constructed Shrouds Mailbox Style Shroud radiation shield required Finishing Hearth Extension= 1/k x inches of thickness From opening In. Micore or equivilent insulation Finishing MaterialFlush Front Combustible MantelGas Code, Ansi Z223.1 AccessoriesGas Log/Lighter Provision Wood Burning InsertsReference Materials Fireplace Dimensions13 mm Catalog # Chimney Components15-1/4 387 mm 15-3/4 400 mm Parts ServicePIER-40 Service PartsThis page intentionally left blank This page intentionally left blank Do not Discard this Manual

PIER-40, BAY-40 specifications

Hearth and Home Technologies has been a leader in the realm of heating solutions, and their innovative products like the BAY-40 and PIER-40 exemplify the cutting-edge technology and design that the brand is known for. These models reflect the shift towards more efficient, environmentally friendly heating options without sacrificing aesthetic appeal or user comfort.

The BAY-40 is a versatile direct vent gas fireplace that offers a stunning flame presentation, making it a focal point in any room. With a heat output of up to 40,000 BTU, it provides ample warmth while maintaining efficiency. This model features an array of customizability options, allowing users to select from various decorative media such as glass or logs to personalize their fireplace. The BAY-40 is also designed for straightforward installation, often requiring less venting compared to traditional fireplaces, making it a practical choice for both new builds and renovations.

On the other hand, the PIER-40 is a premium linear gas fireplace that emphasizes a modern aesthetic. It can be installed indoors or outdoors, providing flexibility for users wanting to create seamless transitions between spaces. The PIER-40 delivers an impressive heat output and is engineered with advanced technology to enhance efficiency and reduce environmental impact. With optional features like LED lighting and customizable front panels, the PIER-40 can cater to various design preferences and settings, from cozy interiors to stylish outdoor living areas.

Both models incorporate innovative technologies such as electronic ignition systems and adjustable flame settings, allowing users to tailor their experience. They also prioritize safety, featuring glass doors that prevent direct contact with flames and heat. Furthermore, they are built with durable materials designed to withstand the rigors of regular use.

In terms of energy efficiency, both the BAY-40 and PIER-40 meet stringent guidelines, often exceeding standard requirements. This not only reduces utility bills for homeowners but also aligns with a growing emphasis on sustainable living.

Overall, Hearth and Home Technologies' BAY-40 and PIER-40 fireplaces represent a commitment to quality, innovation, and user satisfaction. With their blend of modern design, advanced engineering, and customizable features, they are excellent choices for anyone looking to add warmth and style to their home or outdoor space while keeping efficiency and environmental considerations in mind.