Hearth and Home Technologies QV32EV, QV32E, QV32E (120V) Non-Cabinet or Chase Installation

Page 6

Hearth & Home Technologies - Colville

1445 North Highway, Colville, WA 99114-2124

E. INSTALLATION

Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic areas.

If installing the appliance on/over carpeting, the appliance must be installed on a wood or metal panel extending the full width and depth of the appliance.

Note: Follow all national and local electrical codes.

1.Wall Cabinet Kit, Corner Cabinet Kit or Custom Cabinet Installation

*If the power cord is to be used, the Cabinet must provide access to the wall outlet.*

a.For ease of electrical hookup, you may wish to install the appliance near an existing outlet. A 15 amp, 120 volt circuit is required. A dedicated circuit is preferred but not essential in all cases. A dedicated circuit will be required if, after installation, the circuit trips or fuse blows on a regular basis while the appliance is operating. Additional appliances on the same circuit may exceed the current rating of the circuit breaker.

b.If using a listed wall cabinet or corner cabinet, refer to the installation instructions supplied with the kit. For custom cabinets, frame and construct with the opening and depth dimensions listed in Figures 1 and 2.

c.Before plugging the appliance into the wall outlet, make sure all control switches are in the “OFF” position. Open the lower grille panel to gain access to the controls.

d.Before finishing the cabinet, the appliance must be set into the cabinet and the power cord routed to the electrical outlet. If the power cord is not being used, refer to Section “F. Wiring” for hard wiring instructions. If the power cord does not reach the outlet, a No. 16-AWG minimum wire size extension cord rated for a minimum of 1875 watts may be used.

e.To complete the appliance installation, refer to Section “H. Final Installation”.

2.Non-Cabinet or Chase Installation

a.Follow recommended framing dimensions in Figures 1 and 2.

b.Set the appliance into the framed opening. Secure the appliance in place by bending out the two nailing flanges on both sides of the appliance and nail to the framing. The nailing flanges have been positioned 5/8” back from the front of the appliance to allow for the addition of drywall.

c.Wiring instructions for 120/208/240V can be found in Section “F. Wiring”. The power cord must be removed and appliance be hardwired in all non-cabinet or chase installations. Use recommended power supply wire size in accordance to national and local codes. It is recommended to have the appliance on a dedicated service.

d.Remove the protective cover before finishing the front of the appliance. To finish out the appliance, follow the instructions found in Section “G. Finishing”.

e.To complete appliance installation, see Section “H. Final Installation”.

WARNING - RISK OF FIRE!

The power cord must not be pinched or against a sharp edge. Secure cord to avoid tripping or snagging to reduce the risk of fire, electric shock or personal in- jury.

Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic areas and where it will not be tripped over.

WARNING - RISK OF FIRE!

To prevent a possible fire, do not block air intake or exhaust in any manner. Do not use on soft surfaces (like a bed) where openings may become blocked.

CAUTION:

When transporting or storing this appliance and cord, keep in a dry place that is free from excessive vibration. Store so as to avoid damage.

09/03

4030-240 Rev F

VILLAGE COLLECTION ELECTRIC FIREPLACE

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Installation & Operating Instructions Electric FireplacesContents Important InstructionsCanada Certification Appliance DimensionsListing Approvals Description Voltage Watts AmpsClearances Location and ClearancesAppliance Locations and Space Requirements Do not expose appliance to the elements such as rain, etcFraming Installation Non-Cabinet or Chase InstallationWiring Power Supply WiringHardwired appliances only 110V/120V Wiring Diagram Combustible Finishing Material Finishing ChecklistFinishing Noncombustible Finishing MaterialFinal Installation Install the Andirons Place the White Rock Replace the Log AssemblyInstall the Door Front Place the Lava RockOperating Instructions Manual ControlsHand Held Remote Control Transmitter RCE-QUAD Optional Hand Held Remote Transmitter/Appliance InitializationFCC Requirements Remote Transmitter FunctionCleaning the Glass Doors & Back Glass Maintenance InstructionsCleaning the Firebox and Control Compartment Replacing the Light BulbsHeater System Maintenance 2019 Installing the HeaterTroubleshooting Issues Possible Causes SolutionsCabinets Optional ComponentsFront Faces Surrounds & TrimReplacement Parts Log Set Refractories QtyHome Owner’s Notes Symbols IndexWarranty How to Obtain Service

QV32E (120V), QV32EV, QV32E specifications

Hearth and Home Technologies has established a strong reputation for quality and innovation in the realm of home heating solutions. Their line of electric fireplaces, particularly the QV32EV, QV32E, and QV32E (120V), exemplifies this commitment by blending aesthetic appeal with advanced technology.

The QV32EV stands out due to its versatile design, allowing it to fit seamlessly into a variety of spaces, whether modern or traditional. With its 32-inch screen, it offers a striking focal point that captivates any room. The electric fireplace provides realistic, flame-like visuals, employing LED technology that creates an impressive ambiance without the need for wood or gas. Users can enjoy the warmth and glow of a fireplace without the associated hassle of traditional fuel sources, making it an ideal choice for those seeking convenience and functionality.

The QV32E model is similarly designed to deliver the same exceptional features but comes equipped with enhanced control options. It includes a remote control that allows users to adjust flame brightness, heat settings, and even set a timer, ensuring a customized experience. The model is also designed for easy installation, requiring minimal effort to mount on walls or integrate into existing spaces.

For the QV32E (120V), the convenience of using a standard electrical outlet opens the door for easy placement in any area without the complications of gas lines or venting systems. This model also prioritizes safety, featuring an automatic shut-off system that engages when the unit overheats, providing peace of mind for users.

Each model within this series boasts an adjustable heat output, enabling users to select the level of warmth that best suits their needs. The efficient heating technology not only enhances comfort but also lowers energy costs compared to traditional heating methods.

Additionally, the stylish design, coupled with a range of customizable options, allows consumers to select different logs and media to tailor the appearance of their fireplace according to personal style preferences.

In summary, Hearth and Home Technologies' electric fireplaces—QV32EV, QV32E, and QV32E (120V)—offer a perfect blend of aesthetics, functionality, and user-friendly features, making them an unparalleled choice for anyone looking to enhance their living space. Ideal for all types of interiors, these electric fireplaces represent a modern solution for home heating needs, providing both beauty and efficiency.
Top Page Image Contents