Hearth and Home Technologies QVI-30FB-S Installing Vent Pipe and Appliance, Venting Components

Page 11

7 Installing Vent Pipe and Appliance

A. Venting Components

CAUTION

Sharp Edges

•Wear protective gloves and safety glasses during installation.

The vertical vent termination system installed on this model includes:

•One 3-foot section stainless steel flexible pipe (included with insert).

•One length of 3-inch flexible vent pipe for combustion air (included with vent kit).

•Flexible vent pipe for exhaust air (included with vent kit).

•One pipe-to-cap adaptor (included with vent kit).

•One vertical termination cap (included with vent kit).

B. Connecting Vent Pipe

Reference instructions in the termination kit.

•Install the 3-inch flexible vent pipe(s) down through the chimney.

•Secure the exhaust flexible vent pipe to the 3 foot section stainless steel flexible vent pipe using the factory- installed 3-inch collar in the stainless steel section of pipe (see Figure 7.1).

•Use 3 screws to attach either a 4 foot or 30 foot section of inlet air vent to the inlet collar on the collar slide plate (see Figure 7.1). NOTE: The collar slide plate may be removed from appliance to aid installation.

•Seal opening between flex vent and chimney just above insert. Unfaced fiberglass insulation may be used for this purpose.

Note: To achieve optimum performance of insert, minimize or avoid bends in exhaust vent pipe.

TERMINATION

CAP

ADAPTOR

EXHAUST COLLAR

INLET AIR COLLAR

EXHAUST

VENT PIPE

V= 14 FT. MINIMUM 50 FT. MAXIMUM

3 INCH COLLAR

(Factory installed to

stainless steel section)

WARNING: DO NOT

BLOCK PIPE END WITH

INSULATION OR ANY OTHER

SEALING MATERIAL

STAINLESS STEEL

PIPE - 3 FT. MIN.

REQUIRED (INCLUDED)

INLET AIR

VENT PIPE

COLLAR ATTACHMENT

BRACKET

Figure 7.1

Quadra-Fire • QVI-30FB-S • 2020-910 Rev. F • 9/08

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Commonwealth of Massachusetts ModelsModel Number Serial Number Homeowner Reference InformationTable of Contents Listing and Code Approvals Tools and Supplies Needed Design and Installation ConsiderationsGetting Started Inspect Appliance and ComponentsLocation Fireplace Size RequirementsMinimum Fireplace Opening Minimum fireplace opening requirements are shown in FigureClearances to Mantels or other Combustibles above Appliance ClearancesFoot minimum in snow regions Termination LocationsVent Termination Minimum Clearances Fire Risk Asphyxiation RiskMeasuring Standards Vent Information and DiagramsVent Table Key Horizontal VentingInstallation Preparation Reference instructions in the termination kit Installing Vent Pipe and ApplianceConnecting Vent Pipe Venting ComponentsPlacing, Securing and Leveling the Appliance Damper Flashing Kit Optional Installing Adaptor and Termination CapMasonry Factory Built Wood BurningGas Pressures Refer to for location of gas line access in ap- plianceGas Information Fuel Conversions Gas ConnectionHigh Altitude Installations Appliance Requirements Wiring the ApplianceON/OFF Switch Electrical InformationShock hazard Junction Box InstallationInstallation for Fan Optional Optional AccessoriesFAN Junction BOX Mantel Projections Installing Trim SurroundsFinishing Ember Placement Appliance SetupClean the Appliance AccessoriesPositioning the Logs Log Assembly LOGS-QVI30FBLog Placement Quadra-Fire QVI-30FB-S 2020-910 Rev. F 9/08 Quadra-Fire QVI-30FB-S 2020-910 Rev. F 9/08 Replacing Glass Assembly Glass AssemblyAir Shutter Setting Removing Glass AssemblyBefore operating this appliance have a qualified technician Operating InstructionsBefore Lighting Appliance This appliance has a Standing Pilot IgnitionStanding Pilot Ignition Lighting ApplianceDo not operate appliance with glass door removed Initial Break-in ProcedureCheck Pilot Flame Appearance After Appliance is LitFrequently Asked Questions Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Maximum flame impingement. Follow lighting instruc TroubleshootingSymptom Possible Cause Corrective Action Risk of injury or property damage Maintenance TasksMaintaining and Servicing Appliance Inspect Maintenance Tasks Reference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits Vent Kits ComponentsEnding Manufacturing Date Log Set AssemblyService Parts Beginning Manufacturing Date OctAt Depot Service Parts ListStocked Be ordered from an authorized dealer Valve AssemblyCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Important operating Contact Information

QVI-30FB-S specifications

Hearth and Home Technologies has long been a leader in the hearth industry, and their QVI-30FB-S model continues that tradition with a modern twist. The QVI-30FB-S is an innovative gas fireplace that combines a stylish design with advanced technology, providing both warmth and ambiance to any home.

One of the standout features of the QVI-30FB-S is its sleek, contemporary design. With a clean face and large viewing area, this fireplace is perfect for today’s open living spaces. The minimalist aesthetic allows it to blend seamlessly into various décor styles, enhancing the overall look of the room while providing a focal point that captivates the eye.

The QVI-30FB-S utilizes cutting-edge heating technology to deliver efficient warmth. It boasts a high efficiency rating, which means it can effectively heat larger areas without excessive gas consumption. The gas burner system is designed to maximize heat while minimizing emissions, making it an environmentally friendly choice for homeowners looking to reduce their carbon footprint.

Another notable feature is the adjustable flame height. Users can customize the intensity of the flames, allowing for a cozy glow or a more robust fire, depending on their mood and the occasion. The fireplace also includes a backup battery system, ensuring that it remains functional even during power outages, providing peace of mind during inclement weather.

The QVI-30FB-S is equipped with an advanced control system, offering users the convenience of remote operation. With the included remote control, it's easy to adjust the temperature and flame height from anywhere in the room. Additionally, it has a smartphone-compatible option that allows for operation via a mobile app, adding another layer of convenience for tech-savvy users.

Safety is a priority with the QVI-30FB-S. It features a safety shut-off system that activates in the event of a malfunction or abnormal operation, ensuring that users can enjoy their fireplace worry-free.

In summary, the Hearth and Home Technologies QVI-30FB-S is a remarkable gas fireplace that combines style, efficiency, and modern technology. Its design elements, heating capabilities, adjustable features, and safety systems make it an excellent choice for homeowners looking to enhance their living spaces with warmth and elegance.
Top Page Image Contents