Hearth and Home Technologies QVI-30FB-S owner manual Lighting Appliance, Standing Pilot Ignition

Page 26

B. Lighting Appliance

Standing Pilot Ignition

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

LIGHTING

INSTRUCTIONS

1.Turn off all electric power to the appliance.

2.Push in gas control knob slightly and turn clockwise to “OFF”.

A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas sup- plier, call the fire department.

C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explo- sion.

D. Do not use this appliance if any part has been under water. Im- mediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

NOTE: Knob cannot be turned from “PILOT” to “OFF” unless knob is pushed in slightly. Do not force.

3.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the Safety Informa- tion located on the left side of this label. If you don’t smell gas, go to next step.

4.Find the pilot. The pilot is inside combustion chamber next to the main burner.

5.Turn knob on gas control counter clockwise

to “PILOT”.

6. Push in control knob all the way and hold in. Im-

mediately depress red or black piezo button. It may

require several depressions of the red or black

piezo button until PILOT lights. If PILOT light does

WARNING: CAUTION:

not light after 10 seconds, return to step 3. Continue to

hold the control knob in for about one minute after the

pilot is lit. Release knob and it will pop back out. Pilot

should remain lit. If it goes out, repeat steps 3 through 6.

DO NOT CONNECT 110 VAC TO THE CONTROL VALVE.

Improper installation, adjustment, al- teration, service or maintenance can cause injury or property damage. Re- fer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and main- tained in accordance with the man- ufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause can- cer, birth defects, or other reproduc- tive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

Hot while in operation. Do not touch. Keep children, clothing, furniture, gaso- line and other liquids having flammable vapors away.

Do not operate the appliance with panel(s) removed, cracked or broken. Replacement of the panel(s) should be done by a licensed or qualified service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certified for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional informa- tion, consult a qualified installer, ser- vice agency or the gas supplier.

• If knob does not pop up when released, stop and im-

 

mediately call your service technician or gas supplier.

•

If the pilot will not stay lit after several tries, turn

 

the gas control knob to “OFF” and call your service

 

technician or gas supplier.

7.

Turn gas control knob counterclockwise to

“ON”.

8.To light Burner, flip the on/off switch to the “ON” position, and close access grille.

9.Turn on all electric power to the appliance.

TO TURN OFF GAS TO APPLIANCE

1. Turn off all electric power to the appliance if service is to be performed.

2.

Open control access panel.

3.

Move switch to “OFF” position.

4.

Push in gas control knob slightly and turn clock-

 

wise

to OFF”. Do not force.

For additional information on operating your

Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.

5.

Close control access panel.

 

464-903G

26

Quadra-Fire • QVI-30FB-S • 2020-910 Rev. F • 9/08

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Models Commonwealth of MassachusettsHomeowner Reference Information Model Number Serial NumberTable of Contents Listing and Code Approvals Inspect Appliance and Components Design and Installation ConsiderationsGetting Started Tools and Supplies NeededMinimum fireplace opening requirements are shown in Figure Fireplace Size RequirementsMinimum Fireplace Opening LocationClearances Clearances to Mantels or other Combustibles above ApplianceFire Risk Asphyxiation Risk Termination LocationsVent Termination Minimum Clearances Foot minimum in snow regionsHorizontal Venting Vent Information and DiagramsVent Table Key Measuring StandardsInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Reference instructions in the termination kitPlacing, Securing and Leveling the Appliance Factory Built Wood Burning Installing Adaptor and Termination CapMasonry Damper Flashing Kit OptionalFuel Conversions Gas Connection Refer to for location of gas line access in ap- plianceGas Information Gas PressuresHigh Altitude Installations Electrical Information Wiring the ApplianceON/OFF Switch Appliance RequirementsOptional Accessories Junction Box InstallationInstallation for Fan Optional Shock hazardFAN Junction BOX Mantel Projections Installing Trim SurroundsFinishing Accessories Appliance SetupClean the Appliance Ember PlacementPositioning the Logs Log Assembly LOGS-QVI30FBLog Placement Quadra-Fire QVI-30FB-S 2020-910 Rev. F 9/08 Quadra-Fire QVI-30FB-S 2020-910 Rev. F 9/08 Removing Glass Assembly Glass AssemblyAir Shutter Setting Replacing Glass AssemblyThis appliance has a Standing Pilot Ignition Operating InstructionsBefore Lighting Appliance Before operating this appliance have a qualified technicianLighting Appliance Standing Pilot IgnitionAfter Appliance is Lit Initial Break-in ProcedureCheck Pilot Flame Appearance Do not operate appliance with glass door removedFrequently Asked Questions Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Maximum flame impingement. Follow lighting instruc TroubleshootingSymptom Possible Cause Corrective Action Risk of injury or property damage Maintenance TasksMaintaining and Servicing Appliance Inspect Maintenance Tasks Appliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsBeginning Manufacturing Date Oct Log Set AssemblyService Parts Ending Manufacturing DateAt Depot Service Parts ListStocked Valve Assembly Be ordered from an authorized dealerCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information Important operating

QVI-30FB-S specifications

Hearth and Home Technologies has long been a leader in the hearth industry, and their QVI-30FB-S model continues that tradition with a modern twist. The QVI-30FB-S is an innovative gas fireplace that combines a stylish design with advanced technology, providing both warmth and ambiance to any home.

One of the standout features of the QVI-30FB-S is its sleek, contemporary design. With a clean face and large viewing area, this fireplace is perfect for today’s open living spaces. The minimalist aesthetic allows it to blend seamlessly into various décor styles, enhancing the overall look of the room while providing a focal point that captivates the eye.

The QVI-30FB-S utilizes cutting-edge heating technology to deliver efficient warmth. It boasts a high efficiency rating, which means it can effectively heat larger areas without excessive gas consumption. The gas burner system is designed to maximize heat while minimizing emissions, making it an environmentally friendly choice for homeowners looking to reduce their carbon footprint.

Another notable feature is the adjustable flame height. Users can customize the intensity of the flames, allowing for a cozy glow or a more robust fire, depending on their mood and the occasion. The fireplace also includes a backup battery system, ensuring that it remains functional even during power outages, providing peace of mind during inclement weather.

The QVI-30FB-S is equipped with an advanced control system, offering users the convenience of remote operation. With the included remote control, it's easy to adjust the temperature and flame height from anywhere in the room. Additionally, it has a smartphone-compatible option that allows for operation via a mobile app, adding another layer of convenience for tech-savvy users.

Safety is a priority with the QVI-30FB-S. It features a safety shut-off system that activates in the event of a malfunction or abnormal operation, ensuring that users can enjoy their fireplace worry-free.

In summary, the Hearth and Home Technologies QVI-30FB-S is a remarkable gas fireplace that combines style, efficiency, and modern technology. Its design elements, heating capabilities, adjustable features, and safety systems make it an excellent choice for homeowners looking to enhance their living spaces with warmth and elegance.
Top Page Image Contents