Hearth and Home Technologies QVI-30FB-S Junction Box Installation, Installation for Fan Optional

Page 17

B. Junction Box Installation

 

INSERT STRAIN RELIEF

 

AROUND CORD IN THIS END

FEED PLUG

FROM OUTSIDE OF UNIT

 

THROUGH HOLE

SIDEWALL

 

JUNCTION

 

BOX

 

SCREW

 

PROVIDED

 

Figure 9.2 Junction box installation

 

Optional Accessories

Connecting the electrical junction box is required if using a blower or remote.

•Plug the cord into a convenient outlet.

•An electrician may install an outlet box inside the fireplace. Place the outlet in the lower, back corner of the fireplace.

•Must use cord supplied.

CAUTION

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

WARNING

Shock hazard.

•Replace damaged wire with type 105º C rated wire.

•Wire must have high temperature insulation.

C. Installation for Fan (Optional)

On units already installed removal of decorative front, surround and gas insert is required.

•Detach flexible liner from back of unit if insert is installed.

•Remove the four screws on the cover plate (see Figure 9.3).

 

FAN

COVER

 

 

PLATE

POWER

GROUND

 

WIRE

 

CORD

 

 

Figure 9.3

 

 

•Bend up the tabs on the base pan (see Figure 9.4).

•Place the blower in between the bend up tabs.

•Install and wire the blower per instruction shipped with the fan.

•The ground wire of the fan can clip on the side of the base pan.

•Reinstall the cover plate back on the unit. Make sure the fan does not make contact with the back wall to prevent noise from vibration.

Quadra-Fire • QVI-30FB-S • 2020-910 Rev. F • 9/08

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Commonwealth of Massachusetts ModelsModel Number Serial Number Homeowner Reference InformationTable of Contents Listing and Code Approvals Getting Started Design and Installation ConsiderationsInspect Appliance and Components Tools and Supplies NeededMinimum Fireplace Opening Fireplace Size RequirementsMinimum fireplace opening requirements are shown in Figure LocationClearances to Mantels or other Combustibles above Appliance ClearancesVent Termination Minimum Clearances Termination LocationsFire Risk Asphyxiation Risk Foot minimum in snow regionsVent Table Key Vent Information and DiagramsHorizontal Venting Measuring StandardsInstallation Preparation Connecting Vent Pipe Installing Vent Pipe and ApplianceVenting Components Reference instructions in the termination kitPlacing, Securing and Leveling the Appliance Masonry Installing Adaptor and Termination CapFactory Built Wood Burning Damper Flashing Kit OptionalGas Information Refer to for location of gas line access in ap- plianceFuel Conversions Gas Connection Gas PressuresHigh Altitude Installations ON/OFF Switch Wiring the ApplianceElectrical Information Appliance RequirementsInstallation for Fan Optional Junction Box InstallationOptional Accessories Shock hazardFAN Junction BOX Mantel Projections Installing Trim SurroundsFinishing Clean the Appliance Appliance SetupAccessories Ember PlacementPositioning the Logs Log Assembly LOGS-QVI30FBLog Placement Quadra-Fire QVI-30FB-S 2020-910 Rev. F 9/08 Quadra-Fire QVI-30FB-S 2020-910 Rev. F 9/08 Air Shutter Setting Glass AssemblyRemoving Glass Assembly Replacing Glass AssemblyBefore Lighting Appliance Operating InstructionsThis appliance has a Standing Pilot Ignition Before operating this appliance have a qualified technicianStanding Pilot Ignition Lighting ApplianceCheck Pilot Flame Appearance Initial Break-in ProcedureAfter Appliance is Lit Do not operate appliance with glass door removedFrequently Asked Questions Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Maximum flame impingement. Follow lighting instruc TroubleshootingSymptom Possible Cause Corrective Action Risk of injury or property damage Maintenance TasksMaintaining and Servicing Appliance Inspect Maintenance Tasks Reference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits Vent Kits ComponentsService Parts Log Set AssemblyBeginning Manufacturing Date Oct Ending Manufacturing DateAt Depot Service Parts ListStocked Be ordered from an authorized dealer Valve AssemblyCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Important operating Contact Information

QVI-30FB-S specifications

Hearth and Home Technologies has long been a leader in the hearth industry, and their QVI-30FB-S model continues that tradition with a modern twist. The QVI-30FB-S is an innovative gas fireplace that combines a stylish design with advanced technology, providing both warmth and ambiance to any home.

One of the standout features of the QVI-30FB-S is its sleek, contemporary design. With a clean face and large viewing area, this fireplace is perfect for today’s open living spaces. The minimalist aesthetic allows it to blend seamlessly into various décor styles, enhancing the overall look of the room while providing a focal point that captivates the eye.

The QVI-30FB-S utilizes cutting-edge heating technology to deliver efficient warmth. It boasts a high efficiency rating, which means it can effectively heat larger areas without excessive gas consumption. The gas burner system is designed to maximize heat while minimizing emissions, making it an environmentally friendly choice for homeowners looking to reduce their carbon footprint.

Another notable feature is the adjustable flame height. Users can customize the intensity of the flames, allowing for a cozy glow or a more robust fire, depending on their mood and the occasion. The fireplace also includes a backup battery system, ensuring that it remains functional even during power outages, providing peace of mind during inclement weather.

The QVI-30FB-S is equipped with an advanced control system, offering users the convenience of remote operation. With the included remote control, it's easy to adjust the temperature and flame height from anywhere in the room. Additionally, it has a smartphone-compatible option that allows for operation via a mobile app, adding another layer of convenience for tech-savvy users.

Safety is a priority with the QVI-30FB-S. It features a safety shut-off system that activates in the event of a malfunction or abnormal operation, ensuring that users can enjoy their fireplace worry-free.

In summary, the Hearth and Home Technologies QVI-30FB-S is a remarkable gas fireplace that combines style, efficiency, and modern technology. Its design elements, heating capabilities, adjustable features, and safety systems make it an excellent choice for homeowners looking to enhance their living spaces with warmth and elegance.
Top Page Image Contents