Hearth and Home Technologies 2700-I warranty Operation Wood Selection and Storage, Overfiring

2700-I WOOD INSERT (ACT)

R

OPERATION

WOOD SELECTION AND STORAGE

Burn only dry seasoned wood. Dry, well-seasoned wood will not only minimize the chance of creosote formation but will give you the most efficient heat output. Even dry wood con- tains at least 15% moisture by weight and should be burned hot enough to keep the chimney hot enough to maintain par- ticulate (smoke) burning. Burning unseasoned wood of any variety defeats the stoves’ efficiency.

Dead wood lying on the forest floor should be considered wet, and requires full seasoning time. Standing wood can be considered to be about two-thirds seasoned. Wood is dry enough to burn if the ends of the logs have cracks radiating in all directions from the center. If your wood sizzles in the fire, even though the surface is dry, it may not be fully cured.

Drying time can be reduced by splitting wood prior to stor- age. Since the majority of drying occurs through the cut ends rather than the sides, stack the wood so both ends of each piece are exposed to air. Store wood under cover, such as in a shed, or covered with a tarp, plastic, tar paper, sheets of scrap plywood, etc.

OVERFIRING

Do not overfire. Overfiring can result in crazing, an effect causing a white, non-removable film to be deposited on the inside of the glass. Using flammable liquids or too much wood, or burning trash in the insert, may result in overfiring. If the chimney connector or insert glows red, or worse, white, the insert is overfired. This condition may ignite creosote in the chimney, possibly causing a house fire. If any part of the insert starts to glow, you are in an overfire situation. If you overfire, immediately close the insert dampers and door, if open, to reduce the air supply to the fire. Overfiring your insert voids your warranty.

WARNING

Fire Risk.

•Do NOT burn with insert door open. Embers may fall out and start a fire.

BUILDING A FIRE

NOTE: Remove all labels from glass front prior to lighting the first fire and refer to plated surfaces care on page 19 .

Before lighting your first fire in the insert, make certain that the baffle is correctly positioned. It should be resting against the rear support.

There are many ways to build a fire. The basic principle is to light easily-ignitable tinder or paper, which ignites the fast burning kindling, which in turn ignites the slow-burning firewood. Here is one method that works well:

1.Place several wads of crushed paper on the firebox floor. Heating flue with slightly crumpled newspaper before adding kindling keeps smoke to a minimum.

2.Place several wads of crushed paper on the firebox floor.

3.Open Start-Up Air Control (right control) and Primary Air

Control (center control under ashlip) fully. Figure 18.1 on page 18.

4.Ensure that no matches or other combustibles are in the immediate area of the insert, that the room is adequately ventilated, and the flue is unobstructed.

5.Light the paper in the insert. NEVER light or rekindle insert with kerosene, gasoline, or charcoal lighter fluid; the results can be fatal.

6.Once the kindling is burning quickly, add several full-length logs 3 inches (76mm) or 4 inches (102mm) in diameter. Be careful not to smother the fire. Stack the pieces of wood carefully: near enough to keep each other hot, but far enough away from each other to allow adequate air flow between them.

7.When ready to reload the insert, add more logs. Large logs burn slowly, holding a fire longer. Small logs burn fast and hot, giving quick heat.

8.Adjust the Start-Up Air Control and Primary Air Control, maintaining flames above the fuel. The more you close down the Primary Control, the lower and slower the fire will burn. The more you open the Primary Control the more heat will be produced. The Start-Up Air Control (right control) is only used for the first 5 to 15 minutes.

As long as there are hot coals, repeating steps 7 and 8 will maintain a continuous fire.

WARNING

Fire Risk.

Keep combustible materials, gasoline and other flammable vapors and liquids clear of appliance.

•Do NOT store flammable materials in the appliance’s vicinity.

•Do NOT use gasoline, lantern fuel, kerosene, charcoal lighter fluid or similar liquids to start or “freshen up” a fire in this heater.

•Keep all such liquids well away from the heater while it is in use.

•Combustible materials may ignite.

WARNING

Fire Risk.

•Do NOT burn garbage or flammable fluids such as gasoline, naptha or engine oil.

•Do NOT burn treated wood or wood with salt (driftwood).

•May generate carbon monoxide if burn material other than wood.

May result in illness or possible death.

Page 16 7007-161H September 1, 2008