Carrier 33CS400-01 owner manual Viewing the Humidification Run-Time

Page 42

Viewing the Humidification Run-Time

After your humidification system has been operating for the number of days set in step #12 below, the Service Humidify icon will appear. This counter keeps track of the number of days since the Service Humidify icon was reset.

	MODE	Press the MODE button. While holding
		the MODE, press the HUMIDITY button
	HUMIDITY	to enter Setup screens.
	MODE	Press the MODE button repeatedly
	MODE	until this setup screen appears.
		until this setup screen appears.

Note: Press the MODE button momentarily to move through the setup screens. Press and hold the MODE button to move back- wards through the setup screens.

Press

FAN

Counts the number of days the humidifier has been running. Press FAN to reset the Service Humidify counter and remove the icon from the display.

0

Service

Setup I2

Humidify

10

Press

HUMIDITY

Press the HUMIDITY button to leave the Setup screens. If no buttons are pressed, the display will leave the setup screens after 30 seconds.

Page 10.3

Image 42

Contents OWNER’S 4Z95 How to Use This Manual Glossary of Terms Page Table of Contents Contents Heating or Cooling Selecting the Heat or Cool ModeHeating Only OffSelecting Your Desired Temperature Adjusting the setpointsContents Front Panel ButtonDisplay Features CoolService Filter icon Section Humidify/DeHumidify icon Sections Contents Until this setup screen appears To enter Setup screensPress the Mode button repeatedly Manual or Auto-Changeover ThermostatOperating Mode when the Thermostat is Configured to be Cooling OnlyHeating or Cooling Selecting Your Desired Temperature adjusting setpoints Viewing the Outside Temperature Viewing the Indoor Humidity Viewing the Outside Temperature Press the Outside button to view the Outside temperatureViewing the Indoor Humidity To view the indoor humidityOverride Operation Overriding the Normal OperationSetting the Fan-Off Time Using the Fan Button Smart Fan OperationUsing the Fan Button Smart Fan OperationSetting the Fan-Off Time Delay Programming a Security LevelAfter a button press Locking/Unlocking the Keypad Appear on the display, then release the buttonsProgramming a Security Level Installing the Humidity SetpointInstalling the Humidity Module Back of 33CS400-01Setting a Thermostat Jumper for Humidity Operation MISC3 outputs, please see SectionAdjusting the Humidification Setpoint Press the HumidityUsing Your Air Conditioner To Dehumidify Using the Dehum TerminalSetting a Thermostat Jumper for Dehumidification Operation Adjusting the Dehumidification Setpoint Press the Mode button onceUsing Your Air Conditioner to Dehumidify Appears only if is set to on Using the Dehum Terminal Run-Time 10.2 Run-Time 10.3Run-Time 10.4 Viewing the Override Operation Run-Time Viewing the Humidification Run-Time Viewing the UV Light Run-Time Electric Heat and Heat Pump Operation Viewing the Heat Pump Reversing Valve Jumper Settings OFF = Gas Electric OperationViewing the Electric Heat Jumper Setting Using Emergency Heat 73 74HEAT12.3 Adjusting the Heat/Cool Differential Adjusting the Cycles Per Hour Adjusting the Deadband Adjust the deadband For the 1st stage Selecting 2nd Stage Turn Off Temperature Select On or Off On 2nd stage willInstalling the Remote Controlling or Reading Remote Temperature RS1...13.313.2 Installing the Remote Sensors Controlling or Reading Remote Temperature RS1 14.4 Dry Contact Operation 14.2Dry Contact Programming 14.3 14.5Dry Contact Operation Appears only if is YESService Pan Dry Contact ProgrammingUnoccupied Random Start Operation Setting and Resetting Service Filter Fan Run-Time 15.2Press the Reset Filter button To enter this setup screenHow to Set and Reset the UV Light Run-Time Alert How to Set and Reset the Humidifier Run-Time Alert Until this setup screen appearsConfiguring the Jumpers 16.2 16.3Configuring the Jumpers MISC3 MISC2 MISC1Explanation of Jumper Settings HUM Jumper SettingY2 Jumper Setting Factory Defaults, Calibration, and Sensors Resetting the Thermostat to Factory Default Settings for default values seeCalibrating the Temperature and Humidity Sensors I200 PmAccessories Advanced Setup Table Index Electric Heating Index See DisplaySetpoint Warranty