Carrier 33CS400-01 owner manual Adjust the deadband For the 1st stage

Page 52

Adjusting the Deadband

For more detailed information, please see the explanation on the previous page.

 

MODE

Press the MODE button. While holding

Note: Press the MODE

 

 

the MODE, press the HUMIDITY button

 

 

button momentarily

HUMIDITY

to enter Setup screens.

to move through the

 

 

 

 

setup screens. Press

 

 

Press the MODE button repeatedly

and hold the MODE

 

MODE

button to move back-

 

until this setup screen appears.

wards through the

 

 

setup screens.

 

 

 

 

 

 

Setup

I9

Adjust the deadband

2

12

for the 1st stage.

(1 - 6 )

 

 

Press

 

HUMIDITY

Press the HUMIDITY button to leave the Setup screens. If no buttons are pressed, the display will leave the setup screens after 30 seconds.

Page 12.5

Page 51 Page 53
Image 52
Page 51 Page 53
Contents OWNER’S 4Z95 How to Use This Manual Glossary of Terms Page Table of Contents Contents Selecting the Heat or Cool Mode Heating OnlyHeating or Cooling OffSelecting Your Desired Temperature Adjusting the setpointsContents Front Panel ButtonDisplay Features CoolService Filter icon Section Humidify/DeHumidify icon Sections Contents To enter Setup screens Press the Mode button repeatedlyUntil this setup screen appears Manual or Auto-Changeover ThermostatOperating Mode when the Thermostat is Configured to be Cooling OnlyHeating or Cooling Selecting Your Desired Temperature adjusting setpoints Viewing the Outside Temperature Viewing the Indoor Humidity Viewing the Outside Temperature Press the Outside button to view the Outside temperatureViewing the Indoor Humidity To view the indoor humidityOverride Operation Overriding the Normal OperationSetting the Fan-Off Time Using the Fan Button Smart Fan OperationUsing the Fan Button Smart Fan OperationSetting the Fan-Off Time Delay Programming a Security LevelAfter a button press Locking/Unlocking the Keypad Appear on the display, then release the buttonsProgramming a Security Level Installing the Humidity SetpointInstalling the Humidity Module Back of 33CS400-01Setting a Thermostat Jumper for Humidity Operation MISC3 outputs, please see SectionAdjusting the Humidification Setpoint Press the HumidityUsing Your Air Conditioner To Dehumidify Using the Dehum TerminalSetting a Thermostat Jumper for Dehumidification Operation Adjusting the Dehumidification Setpoint Press the Mode button onceUsing Your Air Conditioner to Dehumidify Appears only if is set to onUsing the Dehum Terminal Run-Time 10.3 Run-Time 10.2Run-Time 10.4 Viewing the Override Operation Run-Time Viewing the Humidification Run-Time Viewing the UV Light Run-Time Electric Heat and Heat Pump Operation Viewing the Heat Pump Reversing Valve Jumper Settings OFF = Gas Electric OperationViewing the Electric Heat Jumper Setting Using Emergency Heat 73 74HEAT12.3 Adjusting the Heat/Cool Differential Adjusting the Cycles Per Hour Adjusting the Deadband Adjust the deadband For the 1st stage Selecting 2nd Stage Turn Off Temperature Select On or Off On 2nd stage willControlling or Reading Remote Temperature RS1...13.3 Installing the Remote13.2 Installing the Remote Sensors Controlling or Reading Remote Temperature RS1 Dry Contact Operation 14.2 Dry Contact Programming 14.314.4 14.5Dry Contact Operation Appears only if is YESService Pan Dry Contact ProgrammingUnoccupied Random Start Operation Setting and Resetting Service Filter Fan Run-Time 15.2Press the Reset Filter button To enter this setup screenHow to Set and Reset the UV Light Run-Time Alert How to Set and Reset the Humidifier Run-Time Alert Until this setup screen appearsConfiguring the Jumpers 16.2 16.3Configuring the Jumpers MISC3 MISC2 MISC1Explanation of Jumper Settings HUM Jumper SettingY2 Jumper Setting Factory Defaults, Calibration, and Sensors Resetting the Thermostat to Factory Default Settings for default values seeCalibrating the Temperature and Humidity Sensors I200 PmAccessories Advanced Setup Table Index Electric Heating Index See DisplaySetpoint Warranty
Top Page Image Contents