Carrier 33CS400-01 owner manual Calibrating the Temperature and Humidity Sensors, I200 Pm

Page 72

Calibrating the Temperature and Humidity Sensors

Under normal circumstances it will not be necessary to adjust the calibration of the temperature and humidity sensors. If calibration is required, please contact a trained HVAC technician to correctly perform the following procedure.

MODE

Place the thermostat in the OFF mode.


I2:00 Pm	72
OFF	72
Su

MODE

Press and hold the MODE button. While holding the MODE button, press and hold the FAN button for 5 seconds.


Service Filter	DeHumidify Setup 88
Pan UV Light		COOL
AUTO		Outside
OFFON		Remote
FanOn I88		88
		AUXHEAT

FANAll icons will appear on the display.

PRESS

THERMOSTAT SENSOR

Press the UP and DOWN buttons at the same time twice. The thermostat temperature will be displayed and may be calibrated using the UP or DOWN buttons.

TWICE

REMOTE SENSOR

MODE Press the MODE button once. The remote sensor temperature will be displayed and may be calibrated using the UP or DOWN buttons. If a remote sensor is not installed, only dashes will appear.

Override

CALIBRATE

Remote CALIBRATE 17

MODE

HUMIDITY SENSOR

Press the MODE button once. The relative humidity at the thermostat will be

CALIBRATE

displayed and may be calibrated using the UP or DOWN buttons.

After calibration is complete, press the MODE button once to return to normal operation.

Page 17.3

Image 72

Contents OWNER’S 4Z95 How to Use This Manual Glossary of Terms Page Table of Contents Contents Selecting the Heat or Cool Mode Heating OnlyHeating or Cooling OffSelecting Your Desired Temperature Adjusting the setpointsContents Front Panel ButtonDisplay Features CoolService Filter icon Section Humidify/DeHumidify icon Sections Contents To enter Setup screens Press the Mode button repeatedlyUntil this setup screen appears Manual or Auto-Changeover ThermostatOperating Mode when the Thermostat is Configured to be Cooling OnlyHeating or Cooling Selecting Your Desired Temperature adjusting setpoints Viewing the Outside Temperature Viewing the Indoor Humidity Viewing the Outside Temperature Press the Outside button to view the Outside temperatureViewing the Indoor Humidity To view the indoor humidityOverride Operation Overriding the Normal OperationSetting the Fan-Off Time Using the Fan Button Smart Fan OperationUsing the Fan Button Smart Fan OperationSetting the Fan-Off Time Delay Programming a Security LevelAfter a button press Locking/Unlocking the Keypad Appear on the display, then release the buttonsProgramming a Security Level Installing the Humidity SetpointInstalling the Humidity Module Back of 33CS400-01Setting a Thermostat Jumper for Humidity Operation MISC3 outputs, please see SectionAdjusting the Humidification Setpoint Press the HumidityUsing Your Air Conditioner To Dehumidify Using the Dehum TerminalSetting a Thermostat Jumper for Dehumidification Operation Adjusting the Dehumidification Setpoint Press the Mode button onceUsing Your Air Conditioner to Dehumidify Appears only if is set to onUsing the Dehum Terminal Run-Time 10.2 Run-Time 10.3Run-Time 10.4 Viewing the Override Operation Run-Time Viewing the Humidification Run-Time Viewing the UV Light Run-Time Electric Heat and Heat Pump Operation Viewing the Heat Pump Reversing Valve Jumper Settings OFF = Gas Electric OperationViewing the Electric Heat Jumper Setting Using Emergency Heat 73 74HEAT12.3 Adjusting the Heat/Cool Differential Adjusting the Cycles Per Hour Adjusting the Deadband Adjust the deadband For the 1st stage Selecting 2nd Stage Turn Off Temperature Select On or Off On 2nd stage willInstalling the Remote Controlling or Reading Remote Temperature RS1...13.313.2 Installing the Remote Sensors Controlling or Reading Remote Temperature RS1 Dry Contact Operation 14.2 Dry Contact Programming 14.314.4 14.5Dry Contact Operation Appears only if is YESService Pan Dry Contact ProgrammingUnoccupied Random Start Operation Setting and Resetting Service Filter Fan Run-Time 15.2Press the Reset Filter button To enter this setup screenHow to Set and Reset the UV Light Run-Time Alert How to Set and Reset the Humidifier Run-Time Alert Until this setup screen appearsConfiguring the Jumpers 16.2 16.3Configuring the Jumpers MISC3 MISC2 MISC1Explanation of Jumper Settings HUM Jumper Setting Y2 Jumper Setting Factory Defaults, Calibration, and Sensors Resetting the Thermostat to Factory Default Settings for default values seeCalibrating the Temperature and Humidity Sensors I200 PmAccessories Advanced Setup Table Index Electric Heating Index See DisplaySetpoint Warranty