Bryant PSPHA732 Minimum RUN Time J3, Clock Format J4, Temperature Display Format F/C Display J5

Page 12

board. For reference, there are a table of settings and jumper positions printed there as well. They are described here from J3, the rightmost jumper, to J7, the leftmost jumper.

8.1 MINIMUM RUN TIME – J3

•The position of J3 sets the minimum length of time that the thermostat must remain with HEAT or COOL either on or off before it will automatically switch to the alternate On or Off state. This feature prevents short cycling, and provides compressor protection for cooling units. Choices are 2 or 5 minutes. Default position as shipped is 5 minutes.

8.2 CLOCK FORMAT – J4

•The time shown on the thermostat’s clock may be display in 12 or 24-hour format. Set this option to your preference. Default position as shipped is 12-hour format.

8.3TEMPERATURE DISPLAY FORMAT (F/C DISPLAY) – J5

• Temperature may be displayed in Fahrenheit or Celsius with this option. Default position as shipped is F.

8.4SMART RECOVERY – J6

Smart Recovery allows your HVAC system to attempt to recover from a setback period and reach your desired comfort temperature by the beginning of your programmed comfort period. This jumper allows you to choose Smart Recovery to be On or Off. Default position as shipped is Off.

•An initial Smart Recovery will start _ hour before the programmed comfort temperature.

•Maximum Smart Recovery time is one hour.

•If enabled, Smart Recovery will initiate if:

•Recovery is valid, from an evening setback to morning comfort or day setback to evening comfort period.

•In Heat mode, the set temperature of the

comfort period must be higher than the setback period.

•In Cool mode, the set temperature of the comfort period must be lower than the setback period.

8.5 FAN OVERRUN TIME – J7

•When this feature is enabled, Delay ON time between the 1st stage of the compressor and fan is 5 seconds and Delay OFF between the 1st stage of compressor and fan is 1 minute.

•When this feature is disabled, there is no delay time between 1st stage of the compressor and the fan. Default position as shipped is Disabled.

8.6 REPOSITIONING JUMPERS

See the diagram on Page 16 to determine the jumper position corresponding to the option you desire. The table is also printed on the circuit board. If necessary, change the jumper position by pulling it straight off the pins it covers. Replace the jumper over one pin for OPEN, or both pins for CLOSED. When all changes have been made, press the Hardware Reset Button. See HARDWARE RESET.

These jumpers are located inside the thermostat on the rear of its circuit board. To access them, remove the unit from the wall by pressing up on the thumb latch at the bottom of thermostat, and swinging the body up and away to separate them.

To change a setting, the jumper must be repositioned and a Hardware Reset must be performed. See HARDWARE RESET.

9. BATTERIES/MAINTENANCE

•Depending on your installation, your unit may require batteries to control your HVAC system. Replace your thermostat’s batteries at least once a year or when the battery symbol appears in the display.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PSPHA732 Features CompatibilityElectrical Ratings Installation Tools Required LocationRemoval of OLD Unit MountingWiring Also Refer to the Heat Pump Cross-reference Chart onTape the ends of any unused wires Terminal DescriptionsOperating Basics UP/DOWN Change Keys SET DAY and TimeEmergency Emer Autochange AutoDefault Program OverrideFAN Modes Clean Cycle Set to HEAT, COOL, or Auto with the mode switchDisplay Illumination Audible BeepWeekend Programming Time600 AM 800 AMAdvanced Features Keyboard Lock CopyFilter Monitor Filter UsageReset Hardware ResetSoftware Reset Temperature Variation / SwingSET UP Options Dead BandTemperature Display Format F/C Display J5 Smart Recovery J6Minimum RUN Time J3 Clock Format J4Battery Installation Re-hang it on its base plate as described in installationTechnical Assistance Warranty Wiring Diagram Notes Dashed wires are optionalCross Reference Chart for MULTI-STAGE Heat Pumps User Program Table Mercury Warning and Recycling Notice

PSPHA732 specifications

The Bryant PSPHA732 is a top-tier heat pump model designed to provide efficient heating and cooling solutions for residential and light commercial applications. Known for its impressive performance and reliability, this unit exemplifies modern HVAC technology, striking a perfect balance between comfort and efficiency.

One of the standout features of the Bryant PSPHA732 is its advanced variable-speed compressor, which allows for precise temperature control and exceptional energy efficiency. This technology enables the heat pump to operate at multiple speeds, adjusting seamlessly to the heating or cooling demand. As a result, homeowners can enjoy more consistent indoor temperatures while minimizing energy consumption, leading to significant savings on utility bills.

The PSPHA732 also boasts a high Seasonal Energy Efficiency Ratio (SEER) and Heating Seasonal Performance Factor (HSPF), making it one of the most efficient options in the market. With a SEER rating of up to 17 and an HSPF rating of up to 10, this unit qualifies for various energy-efficiency programs and tax credits, further enhancing its value proposition.

Another key characteristic of the Bryant PSPHA732 is its innovative design, which incorporates sound-dampening technology. This includes a specially designed fan and insulated compressor compartment, leading to quieter operation compared to traditional models. This is especially beneficial for homeowners seeking a peaceful indoor environment.

The unit’s durable construction is another highlight, featuring a weather-resistant cabinet designed to withstand harsh outdoor conditions. The galvanized steel exterior, combined with a factory-installed coat of paint, ensures long-lasting performance, protecting the unit from rust and corrosion.

Furthermore, the Bryant PSPHA732 is equipped with advanced controls and connectivity options. It is compatible with Bryant’s smart thermostat, allowing users to monitor and adjust their HVAC system remotely through a smartphone app. This integration not only enhances convenience but also optimizes energy use based on the homeowner's schedule and preferences.

Lastly, the PSPHA732 comes with a comprehensive warranty, providing peace of mind for users. With proper maintenance, this heat pump is designed to offer years of reliable service, making it a smart investment for those looking to enhance their home’s comfort and efficiency.

Overall, the Bryant PSPHA732 stands out as a leading choice in the heat pump market, combining cutting-edge technology, energy efficiency, and user-friendly features to deliver an exceptional climate control experience.
Top Page Image Contents