Installation Tools Required, Location, Mounting

C A U T I O N:

Your thermostat is protected against normal static electric discharges. To minimize the risk of damaging the unit in extremely dry weather, touch a grounded metal object before touching your thermostat.

4. INSTALLATION

4.1 TOOLS REQUIRED

•#1 Phillips screwdriver (small)

•Drill with 3/16-in. (4.8mm) bit

•Wire stripper/cutter

4.2 LOCATION

•On replacement installations, mount the new thermostat in place of the old one, unless the conditions listed below suggest otherwise. On new installations, follow the guidelines listed below.

•Locate the thermostat on an inside wall, about 5 ft. (1.5m) above the floor, in a room that is used often.

•Do not locate where air circulation is poor, such as in a corner or an alcove; or behind an open door.

•Do not install it where there are unusual heating conditions, such as: in direct sunlight; near a lamp, television, radiator, register, or fireplace; near hot water pipes in a wall; near a stove on the other side of the wall.

•Do not locate in unusual cooling conditions, such as: on a wall separating an unheated room; or in a draft from a stairwell, door, or window.

•Do not locate in a damp area. This can lead to corrosion that will shorten thermostat life.

•Do not install the unit until all construction work and painting has been completed.

W A R N I N G:

•Read instructions carefully before removing any wiring from an existing thermostat.

•Label wires before they are removed.

•When removing wires from their terminals, ignore the color of the wires since they may not comply with any standard.

4.3REMOVAL OF OLD UNIT

1.Switch electricity to the furnace and air conditioner OFF; then proceed with the following steps.

2.Remove cover from old thermostat. Most are snap-on types and simply pull off. Some have locking screws on the side. These must be loosened.

3.Note the letters printed near the terminals. Attach labels (enclosed) to each wire to identification. Label and remove wires one at a time. Make sure the wires do not fall back inside the wall.

4.Loosen all screws on the old thermostat and remove it from the wall.

4.4 MOUNTING

5.Strip insulation 3/8 in. (9.5mm) from wire ends and clean off any corrosion.

6.Fill wall opening with non-combustible insulation to prevent drafts from affecting the thermostat.

7.With each thumb on a release tab at the bottom of the body, and fingers over the top of the unit, release the unit from its base plate by squeezing the tabs into the body.

8.Separate the unit from its base plate by pulling the body outward at its bottom.

PSPHA732 specifications

The Bryant PSPHA732 is a top-tier heat pump model designed to provide efficient heating and cooling solutions for residential and light commercial applications. Known for its impressive performance and reliability, this unit exemplifies modern HVAC technology, striking a perfect balance between comfort and efficiency.

One of the standout features of the Bryant PSPHA732 is its advanced variable-speed compressor, which allows for precise temperature control and exceptional energy efficiency. This technology enables the heat pump to operate at multiple speeds, adjusting seamlessly to the heating or cooling demand. As a result, homeowners can enjoy more consistent indoor temperatures while minimizing energy consumption, leading to significant savings on utility bills.

The PSPHA732 also boasts a high Seasonal Energy Efficiency Ratio (SEER) and Heating Seasonal Performance Factor (HSPF), making it one of the most efficient options in the market. With a SEER rating of up to 17 and an HSPF rating of up to 10, this unit qualifies for various energy-efficiency programs and tax credits, further enhancing its value proposition.

Another key characteristic of the Bryant PSPHA732 is its innovative design, which incorporates sound-dampening technology. This includes a specially designed fan and insulated compressor compartment, leading to quieter operation compared to traditional models. This is especially beneficial for homeowners seeking a peaceful indoor environment.

The unit’s durable construction is another highlight, featuring a weather-resistant cabinet designed to withstand harsh outdoor conditions. The galvanized steel exterior, combined with a factory-installed coat of paint, ensures long-lasting performance, protecting the unit from rust and corrosion.

Furthermore, the Bryant PSPHA732 is equipped with advanced controls and connectivity options. It is compatible with Bryant’s smart thermostat, allowing users to monitor and adjust their HVAC system remotely through a smartphone app. This integration not only enhances convenience but also optimizes energy use based on the homeowner's schedule and preferences.

Lastly, the PSPHA732 comes with a comprehensive warranty, providing peace of mind for users. With proper maintenance, this heat pump is designed to offer years of reliable service, making it a smart investment for those looking to enhance their home’s comfort and efficiency.

Overall, the Bryant PSPHA732 stands out as a leading choice in the heat pump market, combining cutting-edge technology, energy efficiency, and user-friendly features to deliver an exceptional climate control experience.