Sinclair ASH-09AK, ASH-13AK service manual Turbo function

Page 17

1hr.

2hrs.

2hrs. above

Tpreset

 

 

Tpreset

 

Tpreset temp.

 

 

Turbo function

Tpreset

 

 

 

The turbo function is available in Cool and Heat modes.

 

Dry function

Dry function is available in Cool and Dehumidifying modes.

Auto fan speed control

In this mode, indoor fan can run with Hig, Mid, Low speeds.

Up and down swing control

After powered on, the lower swing motor will firstly rotate the guide louver to position 0, close up the air outlet vent; After unit turned on, if to set up swing function, when indoor fan stop running, the guide louver will stop at current position, inner fan motor is running, guide louver will resume to swing.From Cool, Dry, Fan modes to Heat mode, the guide louver will be opened at D position, when turn on swing will run at (A-D); from Heat mode to Cool, Dry, Fan mode, the fan louver will turn to B position, if turn on the swing, it will run at (A-C). When unit is turned off, the guide louver will turn to position 0, the swing is only available after preset the swing function, and indoor unit is running.

Note: When to set up at position L to B, A to C, B to D, the guide louver will swing between position W to D.

Displayer

Running figure and mode figure display

After powered on, the figure will be displayed, then only Power/running indicator turn on. When using remote conroller to open the unit, it will turn on, at the same time to display current setting running modes.

Dual 8 display

When the unit is turned on, after powered on, the nixie tube will display the setting temp.(setting range is 16-30 ). When the preset temperature display signal has been received, the nixie tube will display the preset temperature; If the display ambient temperature signal has been received, the nixie tube will display the current indoor ambient temperature, if to set up others by remote controller that the display will maintain its status. At displaying ambient temperature, the unit received the remote control signal, it will display 5s preset temperature then turn to ambient temperature display. The ambient temperature sensor malfunction will display F1; Indoor tube sensor will display F2, wire jumper cap protection displays C5.

PG motor lock protection

When turn on the fan motor, if motor continuously run for a while and the running speed is very slow, in order to prevent motor automatically self-protection, it will stop running and display lock; If currently turns unit on, that dual 8 will display lock error code H6; If current is unit off, will not display the block error information.

Power-off Memory

Memory contents: Mode, UP/DOWN Swing, light, Set temp, Set fan speed.

After de-energized, and re-energized, the unit will start to run with the memory function automatically. The system, if the last remote control signal do not set timer function, will memorize the last remote control signal and run according to it. If the last remote control signal has set timer function, the system is de-energized before the set time,when re-energized, the system will memorize the timer function, the set time will recalculate. If the last remote control signal has set timer function and the system is de-energized after the set time, when re-energized, the system will memorize the running status before de-energized.

Image 17
Contents ASH-09AK, ASH-13AK Page R410a 1Ph 220~240V 50HzTechnical specifications Highly Outdoor unit Indoor unitOutline and installation dimension Outline and installation dimensions of outdoor unit Electrical circuit diagram 2Basic Functions Protection Other controls Page Manual 2 of functions of remote controller RunStop Noise Silencing Protection Turbo function Disassemble the front case Disassemble the front panel, filterDisassemble the guide louver Disassemble water tray Disassemble the electric coverDisassemble the electric box Disassembling motor and cross flow fan Disassembling the evaporatorDisassemble the front panel, filter Support Disassembling the evaporator Conventional 09 Disassembly procedures for indoor unit Disassemble the electric box cover Disassembling the evaporator Conventional 12 Disassembly procedures for indoor unit Disassemble the Light Board and electric cover Disassembling the evaporator Disassemble Rear Grill Disassemble Big HandleDisassemble Top Cover Disassemble Electric Box Disassemble Front PanelDisassemble Right Side Plate Disassemble Four-way Valve Disassemble Axial Flow FanDisassemble Motor and Motor Support Disassemble Compressor Disassemble CapillaryDisassemble Gas and Liquid Valves Failure and analysis Is good. Heat insulation must also be provided for Wrong connection Re-wrap and make it tight Page King Series Page Contents ASH-09AK ASH-09AK Indoor Unit ASH-13AK ASH-13AK Indoor Unit Explosive view and spare parts list of outdoor unit ASH-09AK Outdoor Unit ASH-13AK ASH-13AK Outdoor Unit

ASH-09AK, ASH-13AK specifications

The Sinclair ASH-13AK and ASH-09AK are two remarkable electric aircraft developed by Sinclair Aeronautics, exemplifying cutting-edge technologies and contemporary design philosophies within the realm of aviation. Both models are designed to meet the growing demand for eco-friendly flight solutions, paramount in contemporary aviation discussions focused on sustainability and efficiency.

The ASH-13AK is a sleek glider that emphasizes aerodynamic efficiency. It features a wingspan of 13 meters, designed with advanced composite materials that contribute to its lightweight structure while ensuring robustness. The aerodynamic design allows for excellent lift-to-drag ratios, making it highly efficient in its operational capabilities. With its innovative control surfaces, the ASH-13AK enhances maneuverability, enabling pilots to experience heightened responsiveness during flight.

On the other hand, the ASH-09AK, a slightly smaller variant with a wingspan of 9 meters, focuses on agility and versatility. This model is particularly suited for training environments and leisure flying, offering novice pilots an accessible entry into the world of gliding. The ASH-09AK also incorporates state-of-the-art avionics, ensuring that pilots have access to modern navigation and real-time data during their flights.

Both aircraft integrate advanced battery technologies that provide extended flight times and reduce reliance on ground support. The electric propulsion systems utilized by the ASH-13AK and ASH-09AK allow for quieter operation and zero emissions during flight. This not only minimizes the environmental footprint but also enhances the flying experience by allowing for serene, unobtrusive navigation across the skies.

The intuitive cockpit design in both models includes user-friendly interfaces that display critical flight information, making piloting more accessible even for those less experienced. The ergonomic seating and cockpit layout ensure comfort during extended flights, with ample visibility for the pilot to navigate seamlessly.

In summary, the Sinclair ASH-13AK and ASH-09AK are exemplary electric aircraft that showcase modern engineering prowess. Their focus on sustainability, efficiency, and user-friendly technologies demonstrate Sinclair Aeronautics' commitment to advancing the future of aviation, making them noteworthy additions to the electric aircraft market. With continued innovation and development, both models are set to inspire a new generation of aviators seeking eco-conscious flying experiences.