2
TABLE OF CONTENTS |
|
| |
Packaging | page | 2 | |
Introduction | page | 2 | |
General Information | page | 2 | |
Location | .......................................... | page | 4 |
Appliance and Vent Clearances | page | 5 | |
Requirements for Commonwealth |
|
| |
of Massachusetts | page | 5 | |
Vent Termination Clearances | page | 5 | |
Typical Installation Sequence | page | 6 | |
Detailed Installation Steps | page | 6 | |
Step 1. | Framing | page | 6 |
Step 2. Routing Gas Line | page | 6 | |
Fireplace Specifications | page | 9 | |
Step 3. Install the Vent System | page | 10 | |
Vertical Termination Systems | page | 10 | |
Vent Section Length Chart | page | 11 | |
Vertical Vent Tables and Figures | page | 14 | |
Horizontal Termination System | page | 15 | |
Horizontal Vent Tables and Figures . page | 18 | ||
Venting Using Flexible Vent Pipe | page | 21 | |
Step 4. | Field Wiring | page | 22 |
Step 5. Connecting Gas Line | page | 23 | |
Step 6. | Installing Logs | page | 24 |
Step 7. | Checking Unit Operation | page | 24 |
Step 8. Installing Glass Door | page | 24 | |
Step 9. | Burner Adjustments | page | 25 |
Finishing Requirements | page | 25 | |
Cold Climate Insulation | page | 26 | |
Installation Accessories | page | 26 | |
Gas Conversion Kits | page 28 | ||
This manual is part of a set of three support- ing this product. Refer to manuals 875,036M for Care & Operations and 750,230M for Log Placement Guide.
Please read and understand these instructions before beginning your installation.
PACKAGING
The assembled vented gas fireplace heater is packaged with the folowing:
1 - The logs are packaged in a carton located within the firebox.
2- One bag of volcanic stones is located in the bottom compartment.
3- One envelope containing the litera- ture package, which consists of the homeowner's manual, installation in- structions, log set supplement, warranty, gas access plate, screws (4) and gasket. The envelope is located in the bottom compartment.
4- One vent restrictor, to be used as detailed on page 10.
5- One hood and one control compartment cover and one 45 degree starter elbow are strapped to the top of the unit.
INTRODUCTION
These fireplaces are designed, tested and listed for operation and installation with, and only with, Secure Vent™ Direct Vent System Components, Secure Flex™ Flexible Vent Components manu- factured by Security Chimneys International and
Millivolt appliances are designed to operate on natural or propane gas. A millivolt gas control valve with piezo ignition system pro- vides safe, efficient operation. There is no optional blower with these units.
Electronic appliances are designed to operate on natural or propane gas. An electronic inter- mittent pilot ignition system provides safe, ef- ficient operation. External electrical power is recommended to operate these units. If the system operates on line voltage with 3V adapt- ers, two (2) "D" batteries can be used as a backup in case of a power outage. The elec- tronic appliance can be operated solely with two
(2) "D batteries.
These appliances comply with National Safety Standards and are tested and listed by Omni- Test Laboratories (Report No.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Both millivolt and electronic versions of these appliances are listed by
The Installation must conform to local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane Installa- tion Code, CSA B149.1.
The appliance, when installed, must be elec- trically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.
DO NOT ATTEMPT TO ALTER OR MODIFY THE CONSTRUCTION OF THE APPLIANCE OR ITS COMPONENTS. ANY MODIFICATION OR ALTERATION MAY VOID THE WARRANTY, CERTIFICATION AND LISTINGS OF THIS UNIT.
GENERAL INFORMATION
Note: Installation and repair should be per- formed by a qualified service person. The appli- ance should be inspected annually by a qualified professional service technician. More frequent inspections and cleanings may be required due to excessive lint from carpeting, bedding mate- rial, etc. It is imperative that the control compart- ment, burners and circulating air passage ways of the appliance be kept clean. S'assurer que le brùleur et le compartiment des commandes sont propres. Voir les instructions d'installation et d'utilisation qui accompagnent l'appareil.
TYPICAL INSTALLATION |
Figure 1 |