Sears 139.53975SRT1, 139.53962SRT1 owner manual Install the Door Control, Std instaliation

Page 18

INSTALLATION STEP 6

Install the Door Control

Locate door control within sight of door, at a minimum height of 5 feet where small children cannot reach, away from moving parts of door and door hardware. If installing into drywall, drill 5/32" holes and use the anchors provided. For pre-wired installations (as in new home construction), it may be mounted to a single gang box (Figure 2).

1.Strip 1/4" of insulation from one end of bell wire and connect to the two terminal screws on back of door

control by color: white to 2 and white/red to 1.

2.Pry off cover along one side with a screwdriver blade (see Figure 1). Fasten with

6ABx1-1/4" self-tapping screws (standard installation) or 6-32xl" machine screws (into gang box) as follows:

•Install bottom screw, allowing 1/8" to protrude above wall surface.

•Position bottom of door control on screw head and slide down to secure. Adjust screw for snug fit.

•Drill and install top screw with care to avoid cracking plastic housing. Do not over tighten.

•Insert top tabs and snap on cover.

3.(For standard installation only) Run bell wire up wall and across ceiling to motor unit. Use insulated staples to secure wire in several places. Be careful not to pierce wire with a staple, creating a short or open circuit.

4.Connect the bell wire to the terminal screws on the motor unit panel: white to 2; white/red to 1.

5.Position the antenna wire as shown.

6.Use tacks or staples to permanently attach entrapment warning label to wall near door control, and manual release/safety reverse test label in a prominent location on inside of garage door.

DO NOT connect power and operate opener at this time. The trolley will travel to the full open

To prevent possible SERIOUSINJURYor DEATHfrom electrocution:

•Be sure power is not connected BEFOREinstalling door control.

•Connect ONLYto 24 VOLT low voltage wires.

To prevent possible SERIOUSINJURYor DEATHfrom a closing garagedoor:

•Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet, and awayfrom all moving parts of door.

•NEVERpermit children to operate or play with door control push buttons or remote control transmitters.

•Activate door ONLYwhen it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

•ALWAYSkeep garagedoor in sight until completely closed. NEVERpermit anyoneto cross path of closing garagedoor.

Outside Keylock Accessory Connections

To opener terminal screws: white to 2; white/red to 1

HARDWARE SHOWN ACTUAL SIZE

 

Control

Console

(std instaliation)

Insulated

 

Staples

 

 

 

 

 

 

Control

Console

(pre-wired)

Dry Wail Anchors

Figure

1

 

 

Figure

2

REMOVE

& REPLACE COVER

PRE-WIRED

 

 

 

 

INSTALLATION

Insert Top

 

 

To Remove

 

Tabs Firsl

/ / z

 

Twist

Here

 

position but will not return to the close position until the sensor beam is connected and properly aligned.

TO Replace, ?_

24 Volt

 

2-Conductor

 

Bell Wire in

 

Gang Box

Lighted

Push Button

Top

Mounting

Hole

 

Terminal

"""""_

> Screws

 

Bottom

 

Mounting

Wire

Hole

 

BACK

VIEW

PREMIUM CONTROL CONSOLE

Back Panel

of Opener

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Garage Door Opener Abridor DE Puerta DE Cochera Contents Preparing your garage door Tools neededSectional Door Installation PlanningONE-PIECE Door Installations ONE-PIECEDOOR Without TrackIONE-PIECEDOOR with Track Carton Inventory Assembly Hardware Installation HardwareHardware Inventory Assemble the Rail & Install the Trolley Front RailBack Rails Install the Idler Pulley Fasten the Rail to the Motor UnitInstall the Chain/Cable Attach the Sprocket Cover To reduce the risk of severe injury or death Tighten the ChainDetermine the Header Bracket Location Sectional Door ONE-PIECE Door with TrackProceed to , ONE-PIECE Door Without Track ExampleFloor Install the Header Bracket Wall Header Bracket InstallationCeiling Header Bracket Installation Attach the Rail to the Header Bracket Position the Opener Sectional Door or ONE-PIECEDOOR with TrackHang the Opener Install the Door Control Std instaliationInstall the Lights and Lenses Attach the Emergency Release Rope and HandleElectrical Requirements Install The Safety Reversing Sensor Important Information about Safety Reversing SensorWall installation Installing the BracketsGarage door track installation preferred Floor installationMounting and Wiring the Safety Sensors Aligning the Safety SensorsTroubleshooting the Safety Sensors Fasten the Door Bracket Sectional DoorsONE-PIECEDOORS Finished CeilingMIN Connect Door Arm to TrolleySectional Doors only FastenerAssemble the door arm, Figure Adjustment procedures, FigureALL ONE-PIECE Doors Fully ClosedAdjust the UP and Down Travel Limits HOW and When to Adjust the LimitsIf door does not open at least 5 feet Adjust the Force HOW and When to Adjust the ForcesAdjust Test the Safety Reversal SystemTest the Safety Reversing Sensor TestUsing Your Garage Door Opener Activate your opener with any of the followingLock Feature Using WaU.Mounted Door ControlLight Feature To Open the Door ManuallyTwice a Year Care of Your OpenerOnce a Month Once a YearHaving a Problem? Function Remotes Additional Hand.held Remote ControlTo Erase All Codes From Motor Unit Memory To Add anAdd Or Change Keyless Entry To set a temporary PiNBe programmed KEY Part Description Rail Assembly PartsInstallation Parts KEY PartMotor Unit Assembly Parts KEY Part DescriptionNot Shown Accessori ES Available Only through Sears Parts & ServiceRevisi6n de los simbolos y trminos de seguridad Preparaci6n de la puerta de su cochera Herramientas NecesariasPlanificaci6n Instalacion CON UNA Puerta SeccionalInstalacion CON UNA Puerta Seccional SIN Carril Planificacibn continuaPuerta DE UNA Sola Pieza Puerta DE UNA Pieza CON CarrilInventario de las cajas SECURITY÷Inventario de piezas Tornillera Y Piezas Para EL ArmadoPulg La poleaIoca Monte el riel e instale el troleRielesposteriores AL Motor Riel delanteroEN SU TAMAblO Normal Sujete el riel al motorInstale la polea Ioca Estas Piezas SE Muestran EN SLI TAMAIqO NormalInstale la cadena y cable y coloque la cubierta de la polea Tiene el trole. Cerci6rese de que la cadena no est# torcidaInstrucciones MUY Importantes Para LA Instalacion Apriete la cadenaContinEle con el Paso 2, pgina Determine d6nde va a instalar La mnsula del cabezalPuerta Seccional Puerta DE UNA Sola Pieza CON Carril RasoPuerta DE UNA Sola Pieza SIN Carril De1recorridoInstalacin DE LA Minsula DEL Cabezal EN EL Cielo Raso Instale la mnsula del cabezalInstalacin DE LA Mensula DEL Cabezal EN LA Pared Delantera PuedadeColoque el riel en la mnsula del cabezal Estas Piezas SE Muestran EN SU Tamano NormalColoque el abridor Puerta Seccional O Puerta DE UNA Sola Pieza CON CarrilCuelgue el abridor Estas Piezas SE Muestran EN SU Tamano NormalInstale la unidad de control de la puerta InfedordeInstale las luces y lentes Coloque la cuerda y la manija de emergenciaRequisitos para la instalaci6n elctrica Instale el sensor del sistema de Reversa de seguridad Instalaci6n en el piso Instalacion DE LAS M#NSULASInstalaci6n en la pared La puertaComo Alinear LOS Sensores DE Seguridad Sujete la mnsula de la puerta Puertas SeccionalesEstaspiezas SE Muestranen SU Tamaiio Normal Puertas DE UNA Sola Pieza Cieloraso20 cm 8 pulg Conecte el brazo de la puerta al troleSolo Para Puertas Seccionales 28cm 8 pulgProcedimiento de ajuste, Figura Todas LAS Puertas DE UNA Sola PiezaArme el brazo de la puerta, Figura Conecte el brazo de la puerta al troleSi la puerta no abre por Io menos 1.50 m 5 pies Ajuste el limite del recorrido hacia arriba y hacia abajoCMO Y Cuando Ajustar LOS Limites $i la puerta no cierra eompletamentePruebe la fuerza del recorrido hacia abajo cerrar Ajuste la fuerzaC3MO Y Cuando Ajustar LA Fuerza DEL Abridor Pruebe la fuerza del recorrido hacia arriba abrirPrueba Pruebe el sistema de reversa de seguridadPruebe el sensor del sistema de reversa de seguridad AjustePara reducir el riesgo de lesiones graves o la muerte Cno usar su abridor de puerta de cocheraDe pared C6mo usar la unidad de controlLA Consola DE Control Premium C6mo abrir la puerta manualmenteUna vez al mes Mantenimiento de su abridor de puerta de cocheraLA Bateria DEL Control Remoto Dos veces al aoSi tiene algbn problema El control remote tiene corto alcanceCbmo agregar un control remoto manual adicional Controles remotos de 3 funcionesDe este bot6n estara Para poner un PIN temporal Para poner o cambiar el PIN de la Entrada sin IlavesPara cambiar un PIN existente Motor empiecen aSECURITY+ Garantia SearsGarantialimitadadel Motor Your Home

139.53975SRT1, 139.53962SRT1 specifications

The Sears 139.53962SRT1 and 139.53975SRT1 are two sophisticated garage door opener models that have gained significant attention for their innovative features and technologies. These devices represent the cutting edge of convenience and security in residential garage systems.

One of the standout features of both models is the integrated MyQ technology. This allows users to control their garage doors remotely using a smartphone app, ensuring seamless access even when they are away from home. Whether you’re on vacation or simply running errands, the ability to monitor and control your garage door from anywhere adds an unmatched level of convenience and peace of mind.

Both the 139.53962SRT1 and 139.53975SRT1 come equipped with a powerful ¾ HP motor. This robust motor provides sufficient lifting power for standard-sized garage doors, ensuring efficient and reliable operation. The powerful motor is designed to handle heavy doors with ease, making it a suitable choice for a variety of residential applications.

Safety is a critical aspect of garage door systems, and these models excel in this area. They feature advanced safety sensors that detect obstructions in the door’s path. This means that if something is in the way as the garage door closes, it will automatically reverse, preventing potential accidents and injuries.

In addition to safety sensors, both models are equipped with rolling code technology. This system enhances security by changing the access code every time the remote is used, preventing unauthorized access and potential break-ins.

Another noteworthy characteristic of these garage door openers is their quiet operation. Thanks to a specially designed belt drive system, both models minimize noise during operation, making them ideal for homes with living spaces situated above the garage.

Installation is made simpler with the inclusion of detailed instructions and user-friendly components, allowing most homeowners to set up the system with minimal hassle.

Overall, the Sears 139.53962SRT1 and 139.53975SRT1 garage door openers combine powerful performance with advanced technology, safety features, and ease of use, making them top choices for anyone looking to upgrade their garage door system.
Top Page Image Contents