Sears 139.53962SRT1 ALL ONE-PIECE Doors, Assemble the door arm, Figure, Fully Closed, Ure

Page 27

ALL ONE-PIECE DOORS

1.Assemble the door arm, Figure 4:

•Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap).

•With the door closed, connect the straight door arm section to the door bracket with the

5/16"x1-1/4" clevis pin.

•Secure with a ring fastener.

2.Adjustment procedures, Figure 5:

On one-piece doors, before connecting the door arm to the trolley, the travel limits must be adjusted. Limit adjustment screws are located on the left side panel as shown on page 28. Follow adjustment procedures below.

•Open door adjustment: decrease UP travel limit

-Turn the UP limit adjustment screw counter- clockwise 5-1/2 turns.

-Press the Door Control push button. The trolley will travel to the fully open position.

-Manually raise the door to the open position (parallel to the floor), and lift the door arm to the trolley. The arm should touch the trolley just in back of the door arm connector hole. Refer

to the fully open trolley/door arm positions in the illustration. If the arm does not extend far

enough, adjust the limit further. One full turn equals 2" of trolley travel.

•Closed door adjustment: decrease DOWN travel limit

-Turn the DOWN limit adjustment screw clockwise 5 complete turns.

Figure 5

Fully Closed

Trolley

Door Arm

Connector Hole

Emergency

Door Arm

Closed

Door Bracket

_

Ring

 

 

 

 

Fastener

 

 

 

 

Lock

5/16"-18

 

 

 

Washers

 

 

 

 

5/16"

 

5116"xi

-I/4"

 

Screws _r-_

 

r,g":-ure

4

 

5/16"-18x7/8

Curved Door Arm

-Press the Door Control push button. The trolley will travel to the fully closed position.

-Manually close the door and lift the door arm to

the trolley. The arm should touch the trolley just ahead of the door arm connector hole. Refer to

the fully closed trolley/door arm positions in the illustration. If the arm is behind the connector

hole, adjust the limit further. One full turn equals 2" of trolley travel.

3.Connect the door arm to the trolley:

•Close the door and join the curved arm to the connector hole in the trolley with the remaining clevis pin. It may be necessary to lift the door slightly to make the connection.

•Secure with a ring fastener.

•Run the opener through a complete travel cycle. If the door has a slight "backward" slant in full open position as shown in the illustration, decrease the UP limit until the door is parallel to the floor.

NOTE: When setting the up limit on the following page, the door should not have a "backward" slant when fully open as illustrated below. A slight backward slant will cause unnecessary bucking and/or jerking operation as the door is being opened or closed from the fully open position.

Release Handle

(Undesirable)

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Garage Door Opener Abridor DE Puerta DE Cochera Contents Tools needed Preparing your garage doorPlanning Sectional Door InstallationONE-PIECE Door Installations ONE-PIECEDOOR Without TrackIONE-PIECEDOOR with Track Carton Inventory Assembly Hardware Installation HardwareHardware Inventory Assemble the Rail & Install the Trolley Front RailBack Rails Fasten the Rail to the Motor Unit Install the Idler PulleyInstall the Chain/Cable Attach the Sprocket Cover Tighten the Chain To reduce the risk of severe injury or deathDetermine the Header Bracket Location Sectional Door ONE-PIECE Door with TrackProceed to , ONE-PIECE Door Without Track ExampleFloor Install the Header Bracket Wall Header Bracket InstallationCeiling Header Bracket Installation Attach the Rail to the Header Bracket Sectional Door or ONE-PIECEDOOR with Track Position the OpenerHang the Opener Std instaliation Install the Door ControlAttach the Emergency Release Rope and Handle Install the Lights and LensesElectrical Requirements Important Information about Safety Reversing Sensor Install The Safety Reversing SensorFloor installation Installing the BracketsGarage door track installation preferred Wall installationMounting and Wiring the Safety Sensors Aligning the Safety SensorsTroubleshooting the Safety Sensors Sectional Doors Fasten the Door BracketFinished Ceiling ONE-PIECEDOORSFastener Connect Door Arm to TrolleySectional Doors only MINFully Closed Adjustment procedures, FigureALL ONE-PIECE Doors Assemble the door arm, FigureAdjust the UP and Down Travel Limits HOW and When to Adjust the LimitsIf door does not open at least 5 feet HOW and When to Adjust the Forces Adjust the ForceTest Test the Safety Reversal SystemTest the Safety Reversing Sensor AdjustActivate your opener with any of the following Using Your Garage Door OpenerTo Open the Door Manually Using WaU.Mounted Door ControlLight Feature Lock FeatureOnce a Year Care of Your OpenerOnce a Month Twice a YearHaving a Problem? To Add an Additional Hand.held Remote ControlTo Erase All Codes From Motor Unit Memory Function RemotesAdd Or Change Keyless Entry To set a temporary PiNBe programmed KEY Part Rail Assembly PartsInstallation Parts KEY Part DescriptionMotor Unit Assembly Parts KEY Part DescriptionNot Shown Available Only through Sears Parts & Service Accessori ESRevisi6n de los simbolos y trminos de seguridad Herramientas Necesarias Preparaci6n de la puerta de su cocheraPlanificaci6n Instalacion CON UNA Puerta SeccionalInstalacion CON UNA Puerta Seccional Puerta DE UNA Pieza CON Carril Planificacibn continuaPuerta DE UNA Sola Pieza SIN CarrilSECURITY÷ Inventario de las cajasInventario de piezas Tornillera Y Piezas Para EL ArmadoPulg Riel delantero Monte el riel e instale el troleRielesposteriores AL Motor La poleaIocaEstas Piezas SE Muestran EN SLI TAMAIqO Normal Sujete el riel al motorInstale la polea Ioca EN SU TAMAblO NormalTiene el trole. Cerci6rese de que la cadena no est# torcida Instale la cadena y cable y coloque la cubierta de la poleaApriete la cadena Instrucciones MUY Importantes Para LA InstalacionRaso Determine d6nde va a instalar La mnsula del cabezalPuerta Seccional Puerta DE UNA Sola Pieza CON Carril ContinEle con el Paso 2, pginaDe1recorrido Puerta DE UNA Sola Pieza SIN CarrilPuedade Instale la mnsula del cabezalInstalacin DE LA Mensula DEL Cabezal EN LA Pared Delantera Instalacin DE LA Minsula DEL Cabezal EN EL Cielo RasoEstas Piezas SE Muestran EN SU Tamano Normal Coloque el riel en la mnsula del cabezalPuerta Seccional O Puerta DE UNA Sola Pieza CON Carril Coloque el abridorEstas Piezas SE Muestran EN SU Tamano Normal Cuelgue el abridorInfedorde Instale la unidad de control de la puertaColoque la cuerda y la manija de emergencia Instale las luces y lentesRequisitos para la instalaci6n elctrica Instale el sensor del sistema de Reversa de seguridad La puerta Instalacion DE LAS M#NSULASInstalaci6n en la pared Instalaci6n en el pisoComo Alinear LOS Sensores DE Seguridad Sujete la mnsula de la puerta Puertas SeccionalesEstaspiezas SE Muestranen SU Tamaiio Normal Cieloraso Puertas DE UNA Sola Pieza28cm 8 pulg Conecte el brazo de la puerta al troleSolo Para Puertas Seccionales 20 cm 8 pulgConecte el brazo de la puerta al trole Todas LAS Puertas DE UNA Sola PiezaArme el brazo de la puerta, Figura Procedimiento de ajuste, Figura$i la puerta no cierra eompletamente Ajuste el limite del recorrido hacia arriba y hacia abajoCMO Y Cuando Ajustar LOS Limites Si la puerta no abre por Io menos 1.50 m 5 piesPruebe la fuerza del recorrido hacia arriba abrir Ajuste la fuerzaC3MO Y Cuando Ajustar LA Fuerza DEL Abridor Pruebe la fuerza del recorrido hacia abajo cerrarAjuste Pruebe el sistema de reversa de seguridadPruebe el sensor del sistema de reversa de seguridad PruebaCno usar su abridor de puerta de cochera Para reducir el riesgo de lesiones graves o la muerteC6mo abrir la puerta manualmente C6mo usar la unidad de controlLA Consola DE Control Premium De paredDos veces al ao Mantenimiento de su abridor de puerta de cocheraLA Bateria DEL Control Remoto Una vez al mesEl control remote tiene corto alcance Si tiene algbn problemaCbmo agregar un control remoto manual adicional Controles remotos de 3 funcionesDe este bot6n estara Motor empiecen a Para poner o cambiar el PIN de la Entrada sin IlavesPara cambiar un PIN existente Para poner un PIN temporalSECURITY+ Garantia SearsGarantialimitadadel Motor Your Home

139.53975SRT1, 139.53962SRT1 specifications

The Sears 139.53962SRT1 and 139.53975SRT1 are two sophisticated garage door opener models that have gained significant attention for their innovative features and technologies. These devices represent the cutting edge of convenience and security in residential garage systems.

One of the standout features of both models is the integrated MyQ technology. This allows users to control their garage doors remotely using a smartphone app, ensuring seamless access even when they are away from home. Whether you’re on vacation or simply running errands, the ability to monitor and control your garage door from anywhere adds an unmatched level of convenience and peace of mind.

Both the 139.53962SRT1 and 139.53975SRT1 come equipped with a powerful ¾ HP motor. This robust motor provides sufficient lifting power for standard-sized garage doors, ensuring efficient and reliable operation. The powerful motor is designed to handle heavy doors with ease, making it a suitable choice for a variety of residential applications.

Safety is a critical aspect of garage door systems, and these models excel in this area. They feature advanced safety sensors that detect obstructions in the door’s path. This means that if something is in the way as the garage door closes, it will automatically reverse, preventing potential accidents and injuries.

In addition to safety sensors, both models are equipped with rolling code technology. This system enhances security by changing the access code every time the remote is used, preventing unauthorized access and potential break-ins.

Another noteworthy characteristic of these garage door openers is their quiet operation. Thanks to a specially designed belt drive system, both models minimize noise during operation, making them ideal for homes with living spaces situated above the garage.

Installation is made simpler with the inclusion of detailed instructions and user-friendly components, allowing most homeowners to set up the system with minimal hassle.

Overall, the Sears 139.53962SRT1 and 139.53975SRT1 garage door openers combine powerful performance with advanced technology, safety features, and ease of use, making them top choices for anyone looking to upgrade their garage door system.
Top Page Image Contents