Graco TI15596a, TI15605a important safety instructions Fire and Explosion Hazard

Page 4

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.

WARNING

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc).

Keep work area free of debris, including solvent, rags and gasoline.

Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes are present.

Ground all equipment in the work area. See Grounding instructions.

Use only grounded hoses.

Hold gun firmly to side of grounded pail when triggering into pail.

If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem.

Keep a working fire extinguisher in the work area.

Static charge may build up on plastic parts during cleaning and could discharge and ignite flammable vapors. To help prevent fire and explosion:

Clean plastic parts only in a well ventilated area.

Do not clean with a dry cloth.

Do not operate electrostatic guns in equipment work area.

PRESSURIZED EQUIPMENT HAZARD

Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury.

Follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing equipment.

Tighten all fluid connections before operating the equipment.

Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.

Read MSDSs to know the specific hazards of the fluids you are using.

Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

4

3A0538F

Image 4
Contents High-Flo4-Ball Pumps Contents Related Manuals ModelsPart No. Description Fire and Explosion Hazard Personal Protective Equipment Grounding InstallationFluid supply container follow local code Stand Mount Plumbing Flush Before Using EquipmentWall Mount Accessories Air LineFluid Line Fluid shutoff valve D shuts off fluid flowIG . Typical Installation for 1000, 1500, and 2000cc Pumps KeyIG . Typical Installation for 3000 and 4000cc Pumps Key Pressure Relief Procedure OperationPrime the Pump Stop the Pump at the Bottom of Its StrokeMaintenance Changing the TSL Cutaway of TSL Reservoir, and Fill LinesMaintenance Troubleshooting Problem Cause SolutionDisassembly ReassemblyShield Disassembly Shield ReassemblyReassemble the Coupling Adapter and Tie Rods toMotor Coupler Torque ValuesParts High-Flo Pumps with 1000cc, 1500cc, or 2000cc 4-Ball LowersCommon Parts Ratio, 2000cc PumpsRatio, 1500cc Pumps Ratio, 1000cc PumpsHigh-Flo Pumps with 3000cc or 4000 cc 4-Ball Lowers Ratio, 4000cc Pumps Ratio, 3000cc PumpsDimensions WeightApprox Model MotorMotor Mounting Hole Diagrams NXT ModelMounting Stand Hole Layouts Wall Mount Bracket Technical Data Performance Charts Fluid Outlet Pressure Black CurvesAir Consumption Gray Curves NXT 2200 Air Motor, 2000cc Lower JX20XXFluid Flow in GPM LPM AIR Flow NXT 6500 Air Motor, 3000cc Lower JX44XX NXT 6500 Air Motor, 4000cc Lower JX33XXGraco Standard Warranty Graco Information