State Industries Residential Gas Water Heater instruction manual TEMPERATURE-PRESSURE Relief Valve

Page 11

Figure 10 shows the typical attachment of the water piping to the water heater. The water heater is equipped with 3/4 inch NPT water connections.

NOTE: If using copper tubing, solder tubing to an adapter before attaching the adapter to the cold water inlet connection. Do not solder the cold water supply line directly to the cold water inlet. It will harm the dip tube and damage the tank.

T & P Valve and Pipe Insulation (if supplied)

Remove insulation for T & P valve and pipe connections from carton.

The valve must be marked with a maximum set pressure not to exceed the marked hydrostatic working pressure of the water heater (150 psi = 1,035 kPa) and a discharge capacity not less than the water heater input rate as shown on the model rating plate.

For safe operation of the water heater, the relief valve must not be removed from its designated opening nor plugged.

The temperature-pressure relief valve must be installed directly into the fitting of the water heater designed for the relief valve. Position the valve downward and provide tubing so that any discharge will exit only within 6 inches (15.2 cm) above, or at any distance below the structural floor. Be certain that no contact is made with any live electrical part. The discharge opening must not be blocked or reduced in size under any circumstances. Excessive length, over 30 feet (9.14 m), or use of more than four elbows can cause restriction and reduce the discharge capacity of the valve, see Figures 10 or 14.

No valve or other obstruction is to be placed between the relief valve and the tank. Do not connect tubing directly to discharge drain unless a 6" (15.2 cm) air gap is provided. To prevent bodily injury, hazard to life, or property damage, the relief valve must be allowed to discharge water in quantities should circumstances demand. If the discharge pipe is not connected to a drain or other suitable means, the water flow may cause property damage.

FIGURE11.

Fit pipe insulation over the incoming cold water line and the hot water line. Make sure that the insulation is against the top cover of the heater. Fit T & P valve insulation over valve. Make sure that the insulation does not interfere with the lever of the T & P valve.

Secure all insulation using tape.

TEMPERATURE-PRESSURE RELIEF VALVE

This heater is provided with a properly certified combination temperature - pressure relief valve by the manufacturer.

The valve is certified by a nationally recognized testing laboratory that maintains periodic inspection of production of listed equipment of materials as meeting the requirements for Relief Valves and Automatic Gas Shut-off Devices for Hot Water Supply Systems, ANSI Z21.22 • CSA 4.4, and the code requirements of ASME.

If replaced, the valve must meet the requirements of local codes, but not less than a combination temperature and pressure relief valve certified as indicated in the above paragraph.

The Discharge Pipe:

•Shall not be smaller in size than the outlet pipe size of the valve, or have any reducing couplings or other restrictions.

•Shall not be plugged or blocked.

•Shall be of material listed for hot water distribution.

•Shall be installed so as to allow complete drainage of both the temperature-pressure relief valve, and the discharge pipe.

•Shall terminate at an adequate drain.

•Shall not have any valve between the relief valve and tank.

The temperature-pressure relief valve must be manually operated at least once a year. Caution should be taken to ensure that (1) no one is in front of or around the outlet of the temperature-pressure relief valve discharge line, and (2) the water manually discharged will not cause any bodily injury or property damage because the water may be extremely hot.

If after manually operating the valve, it fails to completely reset and continues to release water, immediately close the cold water inlet to the water heater, follow the draining instructions, and replace the temperature-pressure relief valve with a new one.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Residential GAS Water Heaters Important Definitions Safe INSTALLATION, USE and ServiceGeneral Safety Introduction Table of ContentsPropane HOT Surface Igniter & Main Burner Typical InstallationNatural HOT Surface Igniter & Main Burner Hotterwatercanscald Mixing Valve UsageFacts to Consider about the Location Locating the NEW Water HeaterInsulation Blankets ALL AIR from Outdoors See Figures 7, 8 ALL AIR from Inside Buildings SeeHotter Water can Scald Installing the NEW Water HeaterWater Piping Valve and Pipe Insulation if supplied TEMPERATURE-PRESSURE Relief ValveGAS Piping GAS Piping with FlexibleconnectorFilling the Water Heater Blower Assembly InstallationSequenceofinstallation Sediment TrapsVenting and Installation Vent Connections to Blower AssemblyMaximum and Minimum Vent Lengths CondensateWooden Side Walls Vent Terminal InstallationVenting Masonry Side WallsVertical Vent Termination Restrictions Vertical Vent Through RoofRecommended BRUSH* Size for Primer Cement Applications Vent Pipe PreparationStep G StepbStepe StepfWhat to do if YOU Smell GAS WatertemperatureadjustmentPowerbeforeservicing Do not try to light the burner by handTemperature Setting Burns on Adult Skin Temperature RegulationOperational Conditions For Your InformationStart UP Conditions Burner Operation and Inspection Periodic MaintenanceBurner Cleaning Venting System InspectionDraining TEMPERATURE-PRESSURE Relief Valve OperationDrain Valve Washer Replacement Anode ROD InspectionLeakage Checkpoints ServiceNot Shown Optional Repair Parts ListBurner Assembly Drain PAN Outer Door Alternate Trouble Shooting Troubleshooting GuidelinesTroubleshooting Guidelines Page Page Limitation on Implied Warranties Service and Labor ResponsibilityClaim Procedure Conditions and ExceptionsTennessee Waltz Parkway Ashland City, TN

Residential Gas Water Heater specifications

State Industries has long been a trusted name in the water heating industry, known for its innovative and reliable residential gas water heaters. With a commitment to quality and efficiency, State Industries offers a range of products designed to meet the needs of homeowners. The State Industries Residential Gas Water Heater is an ideal choice for families seeking hot water solutions that balance performance, affordability, and durability.

One of the standout features of the State Industries gas water heater is its high efficiency. Many models are designed with Energy Factor (EF) ratings that exceed federal standards, allowing homeowners to enjoy lower utility bills while reducing their environmental impact. The use of advanced combustion technology ensures that gas is burned efficiently, maximizing available energy and minimizing waste. This is particularly beneficial in areas where gas prices fluctuate, as users can count on consistent savings.

The water heaters are constructed with robust materials, including a glass-lined tank to prevent corrosion and extend the lifespan of the unit. The insulation surrounding the tank minimizes heat loss, contributing to better energy efficiency. State Industries offers various tank capacities, ranging from 30 to 50 gallons, accommodating different household sizes and hot water demands.

Another notable characteristic is the implementation of safety features, such as a temperature and pressure relief valve that ensures safe operation. Some models are equipped with advanced venting technologies that help reduce exhaust emissions and enhance efficiency. Additionally, many gas models come with a reliable ignition system that allows for quick startups and consistent performance.

Incorporating user-friendly designs, State Industries gas water heaters often feature intuitive controls and easy-to-read gauges. This makes it easier for homeowners to monitor performance and adjust settings according to their needs. The availability of modulating gas valves in certain models allows for precise control over the heating process, providing hot water whenever it's needed.

State Industries also provides excellent customer support and extensive warranties for their products, giving users peace of mind. With a combination of efficiency, durability, and performance, the State Industries Residential Gas Water Heater stands out as a preferred option for homeowners looking to invest in reliable and effective water heating solutions. Regardless of the specific model chosen, users can expect a commitment to quality that is synonymous with the State brand.
Top Page Image Contents