State Industries Residential Gas Water Heater Vent Connections to Blower Assembly

Page 14

VENT CONNECTIONS TO BLOWER ASSEMBLY

Figure 15 shows the optimal placement of the 2" to 3" or 3" to 4" reducer; however, the vent can be reduced at any point in the vent system as long as the maximum and minimum vent length requirements are met.

FIGURE15.

VENTING AND INSTALLATION

Plan the layout of the vent system from the vent termination to the water heater considering all of the 90° and 45° elbows plus the number of feet of pipe that would be needed to install the total vent system. The water heater must be vented to the outdoors as described in these instructions. DO NOT connect this water heater to an existing vent or chimney. It must be vented separately from all other appliances. Nonmetallic vent may be used if it has “Heat Deflection Temperature” (HDT@66 psi) or 455 kPa of at least 157°F or 69°C. Typical nonmetallic vent materials meeting this requirement are: PVC (Schedule 40, ASTM D-1785), Coex Cellular Core (Schedule 40, ASTM F-441), CPVC (Schedule 40, ASTM D-2846), ABS (Schedule 40, ASTM D-2661). The fittings, other than the supplied Vent Termination should be equivalent to the following: PVC (Schedule 40, DWV, ASTM D-2665), CPVC (Schedule 40, DWV, ASTM F-438), ABS (Schedule 40 DWV, ASTM D-2661).

The cement used should be as recommended by the vent pipe manufacturer. See the instructions on pages 18 and 19 for the proper method of cutting and cementing the PVC pipe and fittings.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Residential GAS Water Heaters Safe INSTALLATION, USE and Service Important DefinitionsGeneral Safety Table of Contents IntroductionPropane HOT Surface Igniter & Main Burner Typical InstallationNatural HOT Surface Igniter & Main Burner Mixing Valve Usage HotterwatercanscaldLocating the NEW Water Heater Facts to Consider about the LocationInsulation Blankets ALL AIR from Inside Buildings See ALL AIR from Outdoors See Figures 7, 8Hotter Water can Scald Installing the NEW Water HeaterWater Piping TEMPERATURE-PRESSURE Relief Valve Valve and Pipe Insulation if suppliedGAS Piping with Flexibleconnector GAS PipingSediment Traps Blower Assembly InstallationSequenceofinstallation Filling the Water HeaterVent Connections to Blower Assembly Venting and InstallationCondensate Maximum and Minimum Vent LengthsMasonry Side Walls Vent Terminal InstallationVenting Wooden Side WallsVertical Vent Through Roof Vertical Vent Termination RestrictionsVent Pipe Preparation Recommended BRUSH* Size for Primer Cement ApplicationsStepf StepbStepe Step GDo not try to light the burner by hand WatertemperatureadjustmentPowerbeforeservicing What to do if YOU Smell GASTemperature Regulation Temperature Setting Burns on Adult SkinOperational Conditions For Your InformationStart UP Conditions Venting System Inspection Periodic MaintenanceBurner Cleaning Burner Operation and InspectionAnode ROD Inspection TEMPERATURE-PRESSURE Relief Valve OperationDrain Valve Washer Replacement DrainingService Leakage CheckpointsNot Shown Optional Repair Parts ListBurner Assembly Drain PAN Outer Door Alternate Troubleshooting Guidelines Trouble ShootingTroubleshooting Guidelines Page Page Conditions and Exceptions Service and Labor ResponsibilityClaim Procedure Limitation on Implied WarrantiesTennessee Waltz Parkway Ashland City, TN

Residential Gas Water Heater specifications

State Industries has long been a trusted name in the water heating industry, known for its innovative and reliable residential gas water heaters. With a commitment to quality and efficiency, State Industries offers a range of products designed to meet the needs of homeowners. The State Industries Residential Gas Water Heater is an ideal choice for families seeking hot water solutions that balance performance, affordability, and durability.

One of the standout features of the State Industries gas water heater is its high efficiency. Many models are designed with Energy Factor (EF) ratings that exceed federal standards, allowing homeowners to enjoy lower utility bills while reducing their environmental impact. The use of advanced combustion technology ensures that gas is burned efficiently, maximizing available energy and minimizing waste. This is particularly beneficial in areas where gas prices fluctuate, as users can count on consistent savings.

The water heaters are constructed with robust materials, including a glass-lined tank to prevent corrosion and extend the lifespan of the unit. The insulation surrounding the tank minimizes heat loss, contributing to better energy efficiency. State Industries offers various tank capacities, ranging from 30 to 50 gallons, accommodating different household sizes and hot water demands.

Another notable characteristic is the implementation of safety features, such as a temperature and pressure relief valve that ensures safe operation. Some models are equipped with advanced venting technologies that help reduce exhaust emissions and enhance efficiency. Additionally, many gas models come with a reliable ignition system that allows for quick startups and consistent performance.

Incorporating user-friendly designs, State Industries gas water heaters often feature intuitive controls and easy-to-read gauges. This makes it easier for homeowners to monitor performance and adjust settings according to their needs. The availability of modulating gas valves in certain models allows for precise control over the heating process, providing hot water whenever it's needed.

State Industries also provides excellent customer support and extensive warranties for their products, giving users peace of mind. With a combination of efficiency, durability, and performance, the State Industries Residential Gas Water Heater stands out as a preferred option for homeowners looking to invest in reliable and effective water heating solutions. Regardless of the specific model chosen, users can expect a commitment to quality that is synonymous with the State brand.
Top Page Image Contents