3D Connexion 7318 instruction manual Important Safety Instructions

Page 2

IMPORTANT SAFETY INSTRUCTIONS

This sewing machine is not a toy. Do not allow children to play with this machine.

The machine is not intended for use by children or mentally infirm persons without supervision. This sewing machine is designed and manufactured for household use only.

Read all instruction before using this sewing machine.

DANGER – To reduce the risk of electric shock:

1.An appliance should never be left unattended when plugged in. Always unplug this sewing machine from the electric outlet immediately after using and before cleaning.

2.Always unplug before replacing a sewing machine bulb. Replace bulb with same type rated 15 watts.

3.Do not reach for the appliance that has fallen into water. Unplug immediately.

4.Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.

WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:

1.Do not allow children to play with the machine. The machine is not intended for use by children or infirme persons without proper supervision.

Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or near children.

2.Use this appliance only for its intended use as described in this owner’s manual.

Use only attachments recommended by the manufacturer as contained in this owner’s manual.

3.Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water.

4.Never operate the appliance with any air opening blocked. Keep ventilation opening of this sewing machine and foot controller free from accumulation of lint, dust and loosen cloth.

5.Never drop or insert any object into any opening.

6.Do not use outdoors.

7.Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

8.To disconnect, turn all controls to the off (“O”) position, then remove plug from outlet.

9.Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

10.Keep fingers away from all moving parts. Special care is required around the sewing machine needle.

11.Always use the proper needle plate. The wrong plate can cause the needle to break.

12.Do not use bent needles.

13.Do not pull or push fabric while stitching. It may deflect the needle causing it to break.

14.Switch this sewing machine off (“O”) when making any adjustment in the needle area, such as threading the needle, changing the needle, threading the bobbin or changing the presser foot, and the like.

15.Always unplug this sewing machine from the electrical outlet when removing covers, lubricating, or when making any other adjustments mentioned in this owner’s manual.

SAVE THESE INSTRUCTIONS

The design and specifications are subject to change without a prior notice.

Please note that on disposal, this product must be safely recycled in accordance with relevant National

legistlation relating to electrical/electronic products. If in doubt please contact your retailer for guidance.

(European Union only.)

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Page Important Safety Instructions Table of Contents Know Your Machine Names of PartsExtension Table Standard AccessoriesAccessory storage To detachFree-arm sewing Connecting the Power SupplyOperating Instructions Dropping the Feed Dog Controlling the Sewing SpeedReverse Stitch Lever Foot controlRemoving and Attaching the Foot Holder Raising and Lowering the Presser FootChanging the Presser Foot To removeNeedle and Thread Chart Changing NeedlesAdditional spool pin Setting the spoolWinding the Bobbin Removing the bobbinWinding the bobbin Inserting the bobbin Threading the Machine To set the needle threadDrawing up the Bobbin Thread Stitch Length Dial Selecting the Stitch PatternPattern Selector Dial Variable needle position Adjusting stretch stitch balanceStitch Width Dial Needle thread tension is too tight Balancing Needle Thread TensionBalanced tension Needle thread tension is too looseStarting to sew Machine settingStraight Stitch Sewing Changing the sewing directionSeam guides on the needle plate Turning a square cornerBasic Zigzag Machine setting Overcasting Machine settingKnit Stitch Tricot Stitch Multiple Zigzag StitchStraight Stretch Stitch Zigzag Stretch StitchButton Sewing To adjust buttonhole stitch density Step ButtonholeCorded Buttonhole Fabric preparation Zipper ApplicationAttaching the zipper foot To sew Raise and release the foot, and re-attach it Blind Hemming Decorative Satin Stitches Decorative Stretch StitchesSmocking StepPin Tucking Shell TuckingFagoting PatchworkCare Maintenance Replacing the Bobbin Holder Replacing the Light BulbTroubleshooting Condition Cause Reference Breaks

7318 specifications

The 3D Connexion 7318 is a cutting-edge input device designed specifically for professionals in 3D design and modeling. This innovative product offers a new level of control and precision, making it an essential tool for architects, engineers, and designers. Its advanced technology is tailored to enhance the creative process, allowing users to navigate complex 3D environments with ease.

One of the most notable features of the 3D Connexion 7318 is its intuitive six degrees of freedom (6DoF) functionality. This allows users to move, zoom, and rotate their 3D models in real time, providing a fluid and natural interaction within design software. The device's advanced sensor technology detects the slightest movements, ensuring precision and accuracy with minimal effort. Whether tilting, rotating, or panning, users can maneuver their designs effortlessly, enhancing productivity and creativity.

The 3D Connexion 7318 also incorporates customizable buttons that can be programmed to perform specific functions, providing tailored shortcuts for various software applications. This feature allows users to streamline their workflow, leading to improved efficiency while working on intricate designs. The ergonomic design of the device ensures comfort during prolonged use, with a thoughtful layout that reduces strain on the wrist and fingers.

Moreover, the device is compatible with a wide range of professional 3D applications, including popular software such as AutoCAD, SolidWorks, Autodesk 3ds Max, and more. This extensive compatibility makes the 3D Connexion 7318 a versatile tool that integrates seamlessly into any designer’s toolkit. Additionally, it boasts an impressive build quality, featuring durable materials that ensure longevity even in demanding environments.

In conclusion, the 3D Connexion 7318 stands out as a powerful and efficient tool for professionals in 3D modeling and design. With its advanced 6DoF navigation, customizable controls, and ergonomic design, it enhances the creative process while offering precision and comfort. Whether in an architectural firm or an engineering office, the 3D Connexion 7318 is an invaluable asset for any design professional looking to elevate their work to new dimensions.
Top Page Image Contents