ITT IM213 manual Safety Instructions, Death

Page 3
When in operation, the motor and pump could start unexpectedly and cause serious injury.
3

! Safety Instructions

Section 1

Important: Read all safety information prior to installation of the Controller.

Note

This is a SAFETY ALERT SYMBOL. When you see this symbol on the controller, pump or in this manual, look for one of the following signal words and be alert to the potential for personal injury or property damage. Obey all messages that follow this symbol to avoid injury or death.

DANGER

WARNING

CAUTION

CAUTION

NOTE

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Used without a safety alert symbol indicates a potentially hazardous situation which, if not avoided, could result in property damage.

Indicates special instructions which are very important and must be followed.

 

 

Note

 

 

 

All operating instructions must be read, understood, and followed by the operating personnel.

 

 

Goulds Pumps accepts no liability for damages or operating disorders which are the result of

 

 

non-compliance with the operating instructions.

1.

 

 

 

This manual is intended to assist in the installation, operation and repair of the system and must be kept with

 

the system.

 

2.

Installation and maintenance MUST be performed by properly trained and qualified personnel.

3.

Review all instructions and warnings prior to performing any work on the system.

4.

Any safety decals MUST be left on the controller and/or pump system.

5.

 

 

The system MUST be disconnected from the main power supply before attempting any operation

 

DANGER

 

 

Hazardous

or maintenance on the electrical or mechanical part of the system. Failure to disconnect electrical

 

 

voltage

power before attempting any operation or maintenance can result in electrical shock, burns or

 

 

 

 

 

 

death.

6.

CAUTION

Hazardous Pressure

Page 2 Page 4
Image 3
Page 2 Page 4
Contents IM213 Commercial Water ITTIndex Death Safety InstructionsVolt = System ComponentsController Product Code Information HP =Fusible Disconnect System DesignSection Diagram #2 shows a set-up for municipal water connectionPressure Tank, Pressure Relief Valve and Discharge Piping Installing the Pressure SensorPiping GeneralMounting the Controller Power Supply and Wiring Power SupplyDelta/Wye with grounded Wye neutral Ungrounded secondary Delta/Delta with grounded legResistance grounding and ground fault protection Open Delta consult factoryFor Frame Size 1 Controllers Single Phase Connection 208/230460 20ºC 30ºC 40ºC 50ºC Conduit, Wire and Fuse SizingInput Power and Line Transformer Requirements Output Power ConnectionsStarting the System Input Power Connections Chart below shows the motor overload setting for each model Setting the Motor Overload SwitchesSetting the Carrier Frequency Switch Setting the Acceleration/Deceleration SwitchesSetting the No Water Restart Time Switches Setting the Minimum Frequency SwitchSetting the Pressure Motor Rotation DirectionSystem Status Input and Output Functions Standby TroubleshootingUse the following table to help troubleshoot problems SwitchIncorrect setting of Motor Overload Setting switches Constant Controller ErrorPower. If the error persists, replace controller This fault can be caused bySet the meter to read DC current mA Connect the black lead from the meter to terminalSensor cable To 50% or lower Blinks Temperature This fault can be caused byTemperature reaches 104 ºF 40ºC Megger readings10Hz for 5 minutes Greater than 275V for 230V units and 560V for 460V unitsController Dimensions Input Appendix Input Wire Sizing ChartsPage IM213 Revision Number November

IM213 specifications

ITT IM213 is a prominent electronic device designed for data acquisition and monitoring in various industrial applications. Known for its robust construction and versatile functionality, the IM213 series has gained significant traction in sectors such as manufacturing, environmental monitoring, and energy management.

One of the key features of the ITT IM213 is its advanced data logging capability. The device can record a wide range of signals, including temperature, pressure, and humidity, making it an essential tool for real-time monitoring. The intuitive user interface allows users to configure the device easily, adjusting parameters to suit specific monitoring needs.

The IM213 utilizes cutting-edge technologies to ensure accuracy and reliability. Its high-resolution analog-to-digital converters (ADCs) offer precise measurements with minimal noise interference, enhancing the overall performance of the device. Additionally, the device supports multiple communication protocols, including Modbus, RS-232, and RS-485, enabling seamless integration into existing systems.

Another noteworthy characteristic of the ITT IM213 is its robust build quality. Designed for use in harsh environments, it features an IP67-rated enclosure that protects it from dust, moisture, and other potential contaminants. This makes it particularly suitable for outdoor applications or locations with challenging conditions.

Furthermore, the IM213 is equipped with a range of connectivity options. Users can connect the device to cloud platforms for remote monitoring and data analytics, leveraging IoT technologies to enhance operational efficiency. This capability allows organizations to make data-driven decisions, improving their overall productivity.

The device also supports customizable alert systems, notifying users of any deviations from preset thresholds in real-time. This feature is crucial for preventing costly downtime and ensuring that processes remain within optimal operational parameters.

In terms of power consumption, the ITT IM213 is designed to be energy-efficient, ensuring long operational life and reduced running costs. Its low-power modes further contribute to sustainability, making it a responsible choice for environmentally conscious organizations.

In summary, the ITT IM213 is a versatile and durable data acquisition device that serves a wide range of industrial applications. Its advanced logging capabilities, high accuracy, robust construction, and connectivity options position it as a leading choice for professionals looking to improve their monitoring and data collection efforts. With these features, the IM213 is poised to play a vital role in enhancing productivity and operational efficiency in various sectors.
Top Page Image Contents