Heating

Once you have obtained a good bed of embers you should reload the unit. In order to do so, open the air control completely for a few seconds prior to opening the stove door. Then, proceed by opening the door very slowly. Open it by one or two inches for 5 to 10 seconds before opening it completely. This will increase the draft and will eliminate the smoke, which is stagnant in a state of slow combustion. Then, bring the red embers to the front of the stove and reload the unit. Use only the quantity of wood required depending on the circumstances; for example, in severe cold weather, load the stove to maximum. During milder temperatures, the stove should be only half loaded. CAUTION : DO NOT PLACE LOGS TOO CLOSE TO

THE GLASS OR THE DOOR. IF LOGS ARE TOO CLOSE TO THE GLASS OR THE DOOR, THEY MAY FALL WHEN YOU OPEN THE DOOR. FURTHERMORE, THE LOGS THAT ARE TOO CLOSE MAY DAMAGE THE GLASS IF YOU SHUT THE DOOR TO HARD.

When possible, we recommend that you operate the stove with a wood load approximately equivalent to the height of the fire bricks. If you constantly load the stove above the fire bricks, you may damage the firebox and cause the paint to whiten.

In the case of the FX 3000, the exterior air intake and combustion supply control is located underneath the door. It uses a push\pull technique. The air intake is opened when the control knob is completely pulled toward the front and closed when it is pushed toward the back.

It is extremely important that you use your stove in such a way that you do not lower the temperature of the combustion gases inside the chimney too much. For this purpose, we strongly recommend that you install a Drolet chimney thermometer on your exhaust pipe, approximately 18" above the stove. Contact your Drolet dealer in order to buy one. This thermometer will indicate the temperature of your exhaust gases inside the exhaust system. The ideal temperature range is indicated on the thermometer. If temperature is too low, the build-up of creosote is promoted while if temperature is too high, heat is wasted since too large a quantity is emitted into the atmosphere.

In summary, it is very easy to operate your wood stove and you can prevent all potential problems by following these recommendations:

1)Select a stove of adequate size: selecting a stove that is too big for the area to be heated is a common mistake;

2)Follow the installation standards scrupulously and respect the clearances to combustible material;

3)Burn only dried wood, that is, with a maximum 20% humidity content;

4)Install a chimney thermometer on your stove pipe, 18" (457 mm) above the stove, and maintain the temperature of your exhaust gases between 250°F and 475°F.

Keep in mind that the most difficult months for wood heating are October and November. Indeed, during this period, the atmosphere is often very heavy and humid, and may hinder the chimney draft. Moreover, the wood is often too damp, since it has not had a sufficient drying period, or it has been stored outside in the rain. Combustion problems may then occur.

Important:

It is important to note that wood combustion consumes ambient oxygen in the room. In the case of negative pressure, it is a good idea to allow for a fresh air intake in the room, either by opening a window slightly or by installing a fresh air intake system on an outside wall.

Wood Stove specifications

Drolet Wood Stoves are renowned for their exceptional heating performance and efficient wood-burning technology, making them a popular choice for homeowners seeking an eco-friendly and cost-effective alternative to traditional heating systems. Founded in Quebec, Canada, Drolet has established itself as a leader in the wood stove industry, providing reliable heating solutions that combine innovative engineering with a commitment to sustainability.

One of the main features of Drolet Wood Stoves is their high-efficiency ratings. Many models boast efficiencies exceeding 80%, allowing users to make the most of their firewood while minimizing emissions. This focus on efficiency not only helps homeowners save on fuel costs but also reduces the environmental impact associated with wood burning. The stoves are designed to meet or exceed stringent EPA emissions standards, ensuring cleaner air quality in the home and surrounding environment.

The technologies integrated into Drolet Wood Stoves are state-of-the-art. The stoves utilize secondary combustion technology, which injects heated air into the combustion chamber, igniting unburned gases and particulates. This process enhances the burning of wood and maximizes heat output while reducing smoke production. Additionally, many models feature a built-in air-wash system that helps keep the glass door clean, providing a clear view of the mesmerizing fire.

Drolet Wood Stoves are constructed with durable materials, including heavy-gauge steel and high-temperature paint finishes, ensuring longevity and resilience against the rigors of everyday use. The design of these stoves is both functional and aesthetically pleasing, with various styles and sizes available to suit different home decors and heating needs. Some models come equipped with advanced features like programmable thermostats and rear or side venting options for versatile installation.

Furthermore, Drolet offers a range of products that include freestanding, fireplace inserts, and cookstoves, making it easy for customers to find a solution that fits their specific space and heating requirements. Users can also select from various accessories to enhance their wood stove experience, including insulated chimneys and heat shields.

In conclusion, Drolet Wood Stoves combine efficiency, innovative technology, and stylish design, providing an effective and sustainable heating solution ideal for any home. With a focus on delivering top-notch performance and environmental responsibility, Drolet continues to be a trusted name in the world of wood burning.